Performance - VW Golf MK7 (2012-2020)

The Forge Motorsport intake for the 2015-on 1.2 & 1.4 TSI removes the restriction of the stock airbox and replaces it with a silicone hose (available in a choice of colours) and free flowing Pipercross cone filter, which offers superior filtration to the stock paper filter. The kit is supplied with everything you need, including instructions for installation. Please note: This will not fit CZE engine with cam breather at the back of the engine *Please note - the Pipercross filter is excluded from the Forge lifetime warranty* For replacement filter please click here: Please watch our video on how to fit an air filter without damaging it.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This induction kit will ensure that your engine can breath freely and maximise any restictions from the OEM air box and filter. The silicone inlet hose is available in a choice of either red, blue or black. The filter itself has been deigned in conjunction with the engineers at Pipercross who are well respected in the motorsport scene especially with the Touring car championship race teams. Everything you require is supplied in the kit with comprehensive instructions. PLEASE NOTE: This will only fit the 1.2 engine with engine code CBZA and CBZB

Read more less

Product Description The Forge Motorsport dump valve for the 2015-on 1.2 TSI engine codes CJZA, CJZC, CJZD, CYVB as found in the Skoda Fabia, Skoda Octavia, VW Golf, VW Polo, Audi A1, Audi A3, Seat Ibiza and Seat Leon. Please note this kit is only compatible with models that do not have a standard turbo mounted diverter valve. Earlier models that have a turbo mounted diverter valve as standard require the kit with part number FMDVA1TSI and FMDVATSI The 1.2 and 1.4 TSI doesn’t have a dump valve from the factory, so this product allows you to have the traditional dump valve noise between gear changes and when letting off the gas pedal. It won’t bring on any check engine lights and the car will drive just as before. This kit totally replaces the plastic pipe from turbo to manifold with a silicon hose (available in a choice of colours), and everything else you need to install the valve is included in the kit together with full instructions. Unlike other valves on the market the Forge valve will not bring on any check engine lights. ( EML )  The Forge silicone hoses in this kit have been designed to include an expensive inner liner of modified silicone known as Flurosilicone. This means the hoses are suitable to be used with modern long-life coolants, Organic Acid Technology coolants (O.A.T.) and oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically. The use of a Flurosilicone liner ensures that Forge silicone hoses are the clear market leader. Lifetime warranty. This Forge valve set up is designed to fit with the standard intake. We cannot guarantee it will fit with all aftermarket intakes. This product design has been registered.  Registration Number:  5004511 Compatible Vehicles Audi A1 1.2 Tsi 2015 Onwards   A1 1.4TSI 2015 Onwards   A3 1.2 Tsi 2015 Onwards   A3 8V 1.4 TSI 2015 Onwards Volkswagen Golf MK7 1.4TSI   Golf Mk7 1.2TSI   Golf Mk7 1.4 150bhp   Jetta 1.4tsi 2015 Onwards   Polo 1.2 Tsi 2015 Onwards Skoda Fabia 1.2 Tsi 2015 Onwards   Octavia 1.2 Tsi 2015 Onwards Seat Ibiza 1.2 Tsi 2015 Onwards   Leon 1.2 Tsi 2015 Onwards   Leon 1.4TSI 2015 Onwards Warranty Warranty Infomation All Forge Motorsport products come with a limited lifetime warranty. All warranty claims must be accompanied by the original proof of purchase to enable us to help you. Failure to supply this proof will result in your claim or enquiry being denied. For further information, please call our customer service team on +44(0)1452 380999 or email info@forgemotorsport.co.uk.

Read more less

Please note: spacers are sold as PAIRS! if you want to do front and rear than qty x2 is needed!These CNC machined precision alloy wheel spacers are 20 mm thick with a 57.1mm bore and dual 5 stud bolt pattern for both 100 and 112mm PCD fitments. The spacers are anodised black to inhibit corrosion and "bonding" to the wheel or hub and are machined with an alloy spiggot to allow centering on the hub. (often called "hubcentric" spacers) The spacers are suitable for most vehicles produced by Volkswagen Group. A 16mm spacer will give an overall track increase of 32mm when fitted to both sides of an axle. These spacers are priced and sold per pair. Please note: Our 11mm, 16mm, and 20mm hubcentric wheel spacers will NOT work on the rear wheels of the MK3 VW 5x100 applications due to the longer length of the center spiggot. There is no problem with the smaller 3mm, 5mm, and 8mm NON-hubcentric spacers. Extended wheel bolts are not supplied.Please note, Due to the nature and complexity of a wheel spacer, customers MUST know that the size they are ordering is correct prior to ordering by measuring your stud length and wheel groove depth. Unfortunately, if over tightened the integrity of the spacer and / or bolts can be compromised - and due to this, any spacer that has been fitted, trial fitted or removed from its packaging can not be returned! Please be aware of this as by ordering you agree to this!

Read more less

Boost gauge fitting kit for the EA888 Gen 3, VAG 1.8 and 2.0 Tsi engines found in many new vehicles including the Golf Mk7, Audi S1, Audi S3 (8V chassis), Seat Leon Cupra 280 etc… This adaptor installs between the boost (MAP) sensor and the inlet manifold. Simple 5 minute install to give you a vacuum / boost connection suitable for installing a boost gauge or dump valve. Our design allows you to refit the original engine cover after installation and is totally reversible.

Read more less

Please note: spacers are sold as PAIRS! if you want to do front and rear than qty x2 is needed!These CNC machined precision alloy wheel spacers are 20 mm thick with a 57.1mm bore and dual 5 stud bolt pattern for both 100 and 112mm PCD fitments. The spacers are anodised black to inhibit corrosion and "bonding" to the wheel or hub and are machined with an alloy spiggot to allow centering on the hub. (often called "hubcentric" spacers) The spacers are suitable for most vehicles produced by Volkswagen Group. A 11mm spacer will give an overall track increase of 22mm when fitted to both sides of an axle. These spacers are priced and sold per pair. Please note: Our 11mm, 16mm, and 20mm hubcentric wheel spacers will NOT work on the rear wheels of the MK3 VW 5x100 applications due to the longer length of the center hub. There is no problem with the smaller 3mm, 5mm, and 8mm NON-hubcentric spacers. Extended wheel bolts are not supplied.Please note, Due to the nature and complexity of a wheel spacer, customers MUST know that the size they are ordering is correct prior to ordering by measuring your stud length and wheel groove depth. Unfortunately, if over tightened the integrity of the spacer and / or bolts can be compromised - and due to this, any spacer that has been fitted, trial fitted or removed from its packaging can not be returned! Please be aware of this as by ordering you agree to this!

Read more less

 compatible for: Audi A3 1.8/2.0 TSI 2015 Onwards Q3 2.0 TSI (2015-2018) S3 2.0 TSI (8V Chassis) 2.0TSI (8Y Chassis) Sportback 2.0TSI (8Y Chassis) SQ2 2.0TSI (2018-2021) TT Mk2 2.0  A31.8/2.0 TSI 2015 Onwards Q32.0 TSI (2015-2018) S3 2.0 TSI (8V Chassis) 2.0TSI (8Y Chassis) Sportback 2.0TSI (8Y Chassis) SQ22.0TSI (2018-2021) TTMk2 Cupra Ateca VZ1, VZ2, VZ3, VZN 2021- Formentor 2.0 TSI (245 BHP) 2.0 TSI (310 BHP) Leon VZ1, VZ2, VZ3 Seat Leon Mk3 2012-2020 Skoda Kodiaq 2.0TSI (EA888 Gen 3) RS 2021- Octavia VRS 2.0 TSI 2013 Onwards Octavia 4 RS Superb 280 4x4 DSG Volkswagen Arteon 2.0 TSI Golf MK7 1.8 TFSI GTI GTI Clubsport ED40 R MK7.5 GTI  R MK8 Clubsport 45 GTI GTI S R Jetta MK7 (2018-2021) 2.0 GLI MK7.5 (2021-) 2.0 GLI Passat 2.0 TSI (2015-2021) T-Roc 2.0 2018-2021 Tiguan 2.0 TSI 2017 Onwards R 2022 Onwards (Gen 4) Touareg 2.0 TSI (2018-2021) Product Description Highlights: Power gains of up to 13BHP (when paired with the appropriate turbo inlet adaptor) Torque gains of up to 17NM (when paired with the appropriate turbo inlet adaptor) Pleated or foam filter available Greater engine sound Made in the UK Lifetime guarantee With our in-house VW Golf MK8R development vehicle we have been able to complete thorough testing on the EA888 gen4 platform, from rolling roads to track time. This has allowed us to create FMINDK44, the second induction kit we have available for the EA888 gen 3 and gen 4 platform (alongside our carbon fibre variant, FMINDK40). This kit features either a Forge Motorsport Ram Air high flow, pleated, synthetic nanofiber filtration filter or a Pipercross foam filter. Both are manufactured for optimum size and fit to the available space giving superior flow and filtration with enhanced breathing for the 2.0 turbo charged engine. It also features a larger surface area than the stock filter and many competitors’ alternatives. The intake diameter has been carefully tuned to provide exactly the correct quantity of air for consistent power gains throughout the rev range and minimising the chance of low-end torque loss; the pipework is specifically designed to feed the turbo without interruption. The result of this is a gain of induction acoustics under acceleration, which improves the driving experience and adds a bit more drama to the EA888 engine. With the use of SolidWorks, our CAD engineers have designed the heat shroud to fit round all the contours of the engine bay. This shroud combined with our specially formulated thermal coatings protects the intake from radiant heat while also guiding the cold air from the OE cold air ducting to the filter and housing. The majority of our dyno testing was done on our VW Golf R MK8 EA888 Gen 4, as such you may find slight variations in gains when fitted to other vehicles sharing this engine. During the final prototypes testing we found that the induction kit with stock turbo inlet produced gains on average of 3.5BHP. However, when paired with our turbo inlet adaptor FMTIA5 (RHD), FMTIA6, or FMTIA9 (LHD), or FMINLMK7, this is where the stock EA888 gen4 engine saw impressive gains, increasing power up to 13BHP at 6500RPM with a significant average power increase from 4500RPM to the 6700RPM Rev limit of 8BHP; while the drivability and the punch from extra torque increases can be felt on the road at between 4000RPM to the rev limit an average gain of 17NM is achieved. It’s worth remembering that this is with a stock ECU and no tune, so we would expect to see mapped cars returning even greater yields of power.     Why Do We Try To Decrease Inlet Air Temperatures (IAT’S)? By utilising the OEM cold air feed, and keeping the heat shield open on the headlight corner side we were able to see a decrease in IAT’s compared to the OEM during testing. By ensuring that the intake heat shield is open on this side it also means that vehicles being tuned to stage 2/3+ have a reduced risk of being restricted with them pulling in a greater quantity of air. Temperature and volume of air supplied to your vehicles engine that is compressed by the turbo charger has a better effect on performance when cool as this is to provide the engine with more oxygen (denser air), thus improving the combustion in each cylinder. In addition, by regulating and reducing the air temperature, it also increases the reliability of an engine by keeping the AFRs (Air Fuel Ratios) in each cylinder at a safe level, which in turn can increase an engines power due to the air being cooler. A bigger bang is then created within the cylinder, providing the correct amount of fuel is added. This can equate to an increase in BHP and torque. It’s worth noting that this induction kit offers a massive amount of air to the EA888 engine, which is a must for anyone looking to push the performance when tuning to stage1, stage 2 and beyond. Not only do you get the bhp performance benefits, but FMINDK44 also offers a greater sound from the engine; particularly when on boost, and our product testers have reported a more responsive throttle too. Careful consideration into the other platforms that share the same engine configurations had also been at the forefront of our development engineers’ minds. This needed various vehicles to be sourced to ensure a perfect fit for many of the VAG groups performance vehicles. You have only got to look at our compatibility list to realise how much research and development has gone into this extraordinary performance induction kit. The kit comes complete with everything you need for installation, which can be carried out in around 1 hour, including a set of full colour instructions. For such an easy to fit product it truly does create some remarkable gains. The kit has been designed not just to increase power but to fit a whole range of vehicles on the MQB platform. This goes as far as to include cars using the OEM turbo elbow and the Forge Motorsport FMTIA5/FMTIA6/FMTIA9 high flow elbows. With FMTIA5/FMTIA6/FMTIA9 using multi ply silicone, it has minimal flex; however the OEM inlet hose uses an accordion rib design which could cause the filter to damage itself or the heat shield. Unlike our competitors, we have included a P-clip and tab on the back of the heat shield, allowing the OEM inlet hose to be secured to the heat shield, meaning no damage and no annoying rattles! Time taken to install - around 1 hour

Read more less

Fits: Golf Mk7 R Models: 2016 - 2019 4 Line set   Why should I change my to Braided Stainless Steel ones? YOUR SAFETY! Better brake pedal feel – firmer under pressure More efficient braking- the PTFE lined, Stainless steel will not expand under load unlike OEM rubber hoses Long Lasting- PVC outer and Stainless-Steel end fittings will outlast the standard Mild Steel and rubber lines many times Available in many outer colour options to compliment your vehicle Rigorously tested and approved to the FMVSS 106 certification standards    

Read more less

Fits: Golf Mk7 GTi Models: 2016 - 2019 4 Line set  Why should I change my to Braided Stainless Steel ones? YOUR SAFETY! Better brake pedal feel – firmer under pressure More efficient braking- the PTFE lined, Stainless steel will not expand under load unlike OEM rubber hoses Long Lasting- PVC outer and Stainless-Steel end fittings will outlast the standard Mild Steel and rubber lines many times Available in many outer colour options to compliment your vehicle Rigorously tested and approved to the FMVSS 106 certification standards    

Read more less

Product Description Highlights: 16bhp Gains 20nm increase in torque\ 24°C temperature drop  Made in the UK Reduced turbo lag No cutting of vehicle to fit Lifetime warranty This part will replace the following OEM parts: 5Q0145803H, 5Q0145803K, 5Q0145803L, 5Q0145803P, 5Q0145803S, 5Q0145803N Following on from our previous intercooler solution for the MK7 golf and MQB chassis variants that utilise the EA888 2.0 GEN3 2.0 TSI engine, we have designed our race intercooler to further enhance performance over the original intercooler and our previous iteration of our cooling solution, designed, developed and tested, at our headquarters in Gloucester UK. Throughout the development process we have strived to improve the efficiency and performance of the EA888 GEN3 engine. Our project brief was to develop an intercooler that utilised all of the available space in the original position of the OEM intercooler along with increasing the size again over our hugely successful product FMMK7FMIC. We also had to ensure the inlet air temperature is reduced, without any negative effects on the boost pressure or engine and transmission cooling. In the MQB chassis the intercooler housing is particularly restricted and confined to a small amount of space, due to it not only housing the intercooler, but also the radiator and air conditioning condenser. The front panel in theory is a sandwich pack that houses the auxiliary cooling components. This means in order to increase the size of the intercooler without paying detriment to the performance of the surrounding items, and with also having very little extra space available, that it can be very difficult to execute the perfect blend of a high flow intercooler within such a close proximity. Our research and development engineers went back to the drawing board looking at previous documented dimensions while also taking new scans of the intercooler housing, this enabled the team to squeeze a further 10mm in depth of the core that houses very snugly into the earlier MQBs platform. We also looked at the differences between the Mk7 and Mk8 cooling components and found that the Mk7 Golf GTI and Golf R has a thicker radiator than the MK8 equivalent models thus meaning we also needed to consider any fitment procedures carefully. The design team started to 3d print the intercooler end tanks while creating a test sample dummy core to fit to the Mk7s platform and check for any clearance issues that may occur. The final chosen design has increased inlet and outlet sizes along with increasing the volumetric capacity to increase flow which aids with future proofing the design to work well with highly tuned stage 3 plus EA888 Gen 3 engines as well as offering the best cooling solutions for either a stock or mildly modified powerplant. This gives the best package for the enthusiast as they start their journey in enhancing the vehicles performance. The 3d printed end tanks and dummy core enabled us to ensure the fit was perfect on the vehicle before any prototype castings or machined billet end tanks were produced ready for dyno testing. Several baffle configurations were designed, and flow simulated to ensure the maximum performance was obtained to keep the core working at its optimum, along with ensuring all its cooling capabilities had been upheld, and that the total volume of the core internal is utilised for optimum performance. With an increase in inlet and outlet sizes, we then turned our attention to the design of our silicone hoses. With flow in mind, we have created a step within the hose so where the hose meets the hot and cold side of the inlet and outlet junctions the transition is seamless, this helps to lesson any disturbance to the airflow and prevent unwanted turbulence. To further aid with flow, the inlet and outlets have been increased to 76mm from the OEM size of 63mm which equates to a 45% increase in surface area. The consideration of space and our clever design has led us to produce several intercooler cores with different fin configurations and internal capacities. Depending on the core design, testing results led us to choose a bar and plate design with over 83% more volume than the OEM intercooler, and with a frontal area increase of 10%. Why do we test different cores? Here at Forge Motorsport, when developing an intercooler, we will test several different cores for each application. For example, a bar and plate style core, a tube and fin style core along with different fin pitches and heights i.e. 22 fins per inch or 17 fins per inch as well as changing the internal fin pitches/shapes and density within the tube enabling to fine tune the amount of pressure drop the intercooler produces. Pressure drop is not always a bad thing, as our testing and research has proven on various projects, this is because the pressurized air velocity is being stalled by the pressure drop within the cooler thus allowing more time to cool the air within the cooler itself, as air passes through the non-pressurized face of the core, that is open to the atmosphere. Too much pressure drop can of course have a problem on the higher performance engines as the intercooler reaches its maximum efficiency the turbo has to work a lot harder to force the air through the core. This in turn creates higher inlet air temps (IAT’s) due to the turbo creating more heat as it is over stressed and worked harder. No pressure drop can also prove to be inefficient as the cooler will not lower the charge temperature again resulting in higher inlet air temperatures. Dyno Results Testing was completed using Performance Remap in Gloucester with their VTEC 4-wheel drive dynamometer; this was to ensure all our data has been achieved with results as accurately as possible by an independent tuner. Peak power was increased from stock by 16bhp and 20nm of torque at 5500RPM with the Forge Motorsport performance intercooler installed. The best news is that there are significant torque gains throughout the rev range, meaning that the car power will pick up quicker and pull the whole way through to redline, including an impressive gain in BHP increase from 5000 RPM TO 6500 RPM. Gains on vehicles with re calibrated software and further hardware performance parts can be expected to be a lot higher due to the substantial drop in IATS when FMINT32 is installed.     During our extensive testing, we let the car heat soak on the dyno until the radiator fans tripped on and off (which gives an inlet temperature of around 40°C), we then did a dyno pull from this point, in doing this it gives a more consistent result and reflects real-world driving conditions more accurately. You can easily see the Forge intercooler cools much quicker and delivers a much greater drop in temperature compared to OEM. After more than six pulls on the dyno we still had super safe IAT’s, and the Forge Motorsport intercooler gave results of 34°C @ 6000 RPM giving a reduction of 58% over the factory’s intercooler intake temps from 58°C just before the rev limiter These tests took place in relatively hot conditions with an ambient dyno cell temperature of 23°C proving how inefficient the stock intercooler is. In the summer months, the stock intercooler along with higher inlet air temperatures will have a hugely negative impact on the engine’s performance. In these conditions, the engine management will retard the ignition, resulting in a lower powered engine as temperatures rise and the ECU then pulls out the timing to stop detonation. On a mapped vehicle, the results will be even more detrimental and can lead to possible premature engine wear. If you use a Golf R for fast road or have a high-performance tune in a hot climate, this product is essential.      Why do we try to reduce IAT's (Inlet Air Temperatures)? Temperature and volume of air supplied to your vehicles engine that is compressed by the turbo charger has a better effect on performance when cool as this is to provide the engine with more oxygen (denser air), thus improving the combustion in each cylinder. In addition, by regulating and reducing the air temperature, it also increases the reliability of an engine by keeping the AFRs (Air Fuel Ratios) in each cylinder at a safe level, which in turn, can increase an engines power due to the air being cooler. A bigger bang is then created within the cylinder, providing the correct amount of fuel is added. This can equate to an increase in BHP and torque. The Forge Motorsport intercooler is a perfect performance enhancing product that fits directly to the OEM mounting points, making for a simple install, in a relatively short period of time. No cutting of any components is needed, making the installation reversible if the vehicle needs to be returned to stock at any time in the future. The core and end tanks are finished in our black textured anti corrosion coating that also aids with its thermal properties and keeps the product looking that bit stealthier or OEM+. The Forge Motorsport lifetime warranty on all hardware products shows the trust we have in the quality of our products while they are being enjoyed on your pride and joy.    

Read more less

​​​​​​Fitting this part increases the airflow into the turbo by replacing the restrictive plastic OEM turbo inlet pipe. This innovative product fits all MQB platforms as well as both left and right hand drive vehicles and is a direct replacement for OEM part code 5Q0129635L. When fitting this part, you will increase the available airflow and create an impressive sound by creating a larger, smoother transition between the turbo inlet hose and compressor housing inlet. An all-aluminium construction that fits with standard inlet hose or aftermarket systems, featuring a precision mandrel bent CNC formed pipe along with a precision CNC high flow machined flange. Twin o-ring seal design between the turbo coupler and inner surface of the turbo inlet ensures no leaks and no debris can be drawn into the turbo internals. This part also fits with our induction hose, FMMK7INDH Increased airflow. All aluminium construction. CNC machined couplers for a precision fit. No check engine lights Black hardwearing powdercoated finish. Compatible with LHD and RHD Up to 8 BHP and 16 ft/lbs or torque improvement Made in Great Britain.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Before fitment, please ensure the spacer fits flat to the back of the wheel. These wheel spacers are hubcentric These CNC machined precision alloy wheel spacers are 13 mm thick with a dual 5 stud bolt pattern for both 100 and 112mm PCD fitments. The spacers are anodised black to inhibit corrosion and "bonding" to the wheel or hub. These spacers are suitable for most vehicles produced by Volkswagen Group. A 13mm spacer will give an overall track increase of 26mm when fitted to both sides of an axle. These spacers are priced and sold per pair. Extended wheel bolts are not supplied.   In The Box:2 x FMWS13 13mm Wheel Spacer1 x Forge Sticker   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less