Performance - Seat Leon MK4 KL 2020-PRESENT

Racingline Performance Silicone Boost Hose Set EA888 Gen4The RacingLine Gen.4 Boost Hose package is a three-piece kit to replace the factory soft flexible rubber hoses and replace them with our beautiful reinforced silicone replacement versions. The kit is a direct OEM replacement: simply remove the factory hoses, and replace them with the three uprated silicone pipes. Simple.Stepped internal joint transitions give a port-matched laminar airflow path, greatly reducing turbulence versus other non-stepped designs.Of course the RacingLine hoses are pressure tested far beyond the turbo’s capabilities, allowing the system to maintain performance under extreme temperature and high-boost conditions. By minimising these restrictions, the smoother airflow and optimised hose routing ensures that the turbo meets less resistance and can thus perform more effectively - moving a larger volume of air and minimising turbulence.Within the kit, the two Intercooler Boost Hoses have unique steel wire helix buried within the silicone construction to eliminate the very real risk of hose collapse, yet still allowing sufficient flexibility without wall distortion and minimising airflow blockage.A great upgrade for any remapped 2.0 TSI EA888 gen.4 car running higher boost than standard. Compatible with the following Vehicles:  > VW Golf 8 GTI 2020+> VW Golf 8 GTI Clubsport 2020+> VW Golf 8 R 2020+> VW Arteon R 2.0 TSI 320ps 2020+> VW T-Roc R 2.0 TSI 2021+> Audi S3 8Y 2020+> Audi A3 2.0 TSI 8Y 2020+> Audi TT 45 TFSI 2.0 TSI 8S 2021+> Audi SQ2 2.0 TSI EA888.4 2021+> Cupra Leon IV 300 TSI FW 2020+> Cupra Leon IV 245 TSI FW 2020+> Cupra Ateca 300PS EA888.4 2021+> Cupra Formentor 310PS 2020+> Cupra Formentor 245PS 2020+> Skoda Octavia IV vRS 2.0 TSI 245ps NX 2020+> Skoda Superb III 3V 2.0 TSI EA888.4 2020+> Skoda Kodiaq vRS 2.0 TSI EA888.4 2021+

Read more less

Upgraded Boost Pipe Kit.For all VWG MQB 2.0 TSI EA888 gen.4for higher output 300/310/320/333PS Continental TurboVWR140013 The RacingLine Boost Pipe Kit for 2.0 TSI MQB 'Evo' gen.4 (Continental turbo) delivers smooth, uninterrupted airflow to increase power and torque, replacing the restrictive, failure-prone factory boost pipes.For Golf mk8 R, GTI CS, Audi S3, Cupra Leon & Formentor & many more. This 3-piece RacingLine GEN.4 Boost Pipe kit for 2.0TSI EA888.4 high-output Continental turbo MQB 'Evo' cars deliver smooth, uninterrupted airflow to increase power and torque, replacing the restrictive failure-prone factory boost pipes. By promoting increased airflow throughout the charge flow path, along with removing boost-leak weak points, performance and reliability gains are guaranteed! The RacingLine Boost Pipe kit for 2.0 TSI gen.4 MQB "evo' delivers smooth, uninterrupted airflow to increase power and torque, replacing the restrictive, failure-prone factory boost pipes on all EA888 gen.4 higher output Continental turbo cars. The 3-piece Boost Pipe kit replaces the factory pipework between the turbocharger, the intercooler, and the throttle body with one-piece, mandrel-bent 6000 series aluminium tubes with thin wall 60mm OD for maximum smooth air flow. It’s by minimising the restrictions of the factory pipes and optimising the routing that this increased airflow is achieved. As well as giving enhanced turbocharger sound and faster spool, fitment of these Boost Pipes ensures that the turbo meets less resistance thus allowing it to perform more effectively - moving a larger volume of air and minimising turbulence. The RacingLine Boost Pipe Kit comprises three separate pieces. Two mandrel-bent hard-pipes for the turbo-intercooler and intercooler-throttle body chargepath, plus a reinforced turbo outlet Silicone Hose for the turbo outlet. The Boost Pipes themselves are formed from single piece, mandrel-bent 6000 series aluminium tube with thin wall 60mm OD. The silicone hose is hand-wound multi-ply over internal wire reinforcement, ensuring resistance to both heat and deformation. Meanwhile, barbed ends on the pipes ensure no risk of blow off, even under extreme boost pressure conditions. As you’d expect from RacingLine, each pipe is hand polished then anodised black with laser etched logos as the finishing touch - to look great in your engine bay, and stay looking great. As with all RacingLine products, perfect fitment is a priority. So, all the mounting brackets are carefully TIG welded to ensure dimensional perfection. And within each kit, RacingLine include a stainless steel Mikalor-brand clamp, OEM rubber mounting bobbins and new bolts to make sure you achieve the perfect installation. Install is direct OEM-replacement and requires no additional drilling or cutting to fit - meaning install is fully reversible. Finally, the Boost Pipes can be used with either factory rubber hoses or, for best results we'd highly recommend pairing them with the RacingLine Gen.4 Boost Hose Kit (VWR140006) APPLICATIONS:2.0 TSI / EA888 Gen.4 enginesContinental Turbo 300-333PSVWR140013 > VW Golf 8 & 8.5 R 2020+> VW Golf 8 & 8.5 GTI Clubsport 2020+> VW Arteon R 2.0 TSI 320ps 2020+> VW T-Roc R 2.0 TSI 2019+> VW Tiguan II R 2.0 TSI 320ps 2020+ > Audi S3 8Y & 8Y.2 2020+> Audi TTS 2.0 TFSI 8S 320ps (EA888.4) 2021+> Audi SQ2 (EA888.4) 2021+ > Cupra Leon 4 & 4.5 300 TSI FW 2020+> Cupra Ateca 300ps (EA888.4) 2021+> Cupra Formentor 310ps 2020+ > Skoda Superb III 3V 2.0 TSI (facelift EA888.4) 2021+  The RacingLine Boost Pipe Kit has three pieces: smooth aluminium mandrel-bent hard-pipes for the turbo-intercooler and intercooler-throttle body airflow, plus a reinforced turbo outlet Silicone Hose:      

Read more less

Key facts Pipe Ø: 3.15" (80.00mm) Barcode (GTIN): Tip style: 115mm GT115 Fitting takes from 1.00 to 1.50 hours FITS: Seat Leon Cupra Leon 2.0TSI 245ps (MQB Evo - OPF/GPF Equipped Models) 2022 and Later Why Buy a Milltek Sport Exhaust? Milltek Sport stainless steel exhausts have a genuine performance edge - noticable power gains, sounds that are truly awesome, styled looks that are aggressive but discrete and a feeling of true exhilaration. Transforms performance and driveability Sharper throttle response Substantial weight saving over original equipment exhaust systems Precision, quality controlled manufacture to ISO 9001 standards Highest quality aircraft-grade stainless steel Low pressure stainless exhaust systems for maximum performance - with no loss of low end torque High quality type-304 aircraft grade stainless steel Over 30 years of continuous exhaust development and technical expertise Ever expanding comprehensive selection of performance exhausts Milltek Sport are on tuning companies ‘must-have’ list and are exported to over 70 countries worldwide Designed and manufactured in the UK Milltek Sport stainless steel exhausts come with a lifetime guarantee for the first purchaser (excluding cats & flexis)   Milltek Sport exhausts are produced in high quality type 304 aircraft grade stainless steel. This material is anti-magnetic (other manufacturers' stainless steel may not be) and is less susceptible to discolouration. This quality of stainless steel is used on all pipework and the total construction of the silencer. Mandrel bending ensures full flow bends for better gas flow and Milltek Sport exhaust systems are increased in bore to ensure ultimate performance without the loss of mid-range torque. All Milltek Sport exhausts are designed, developed and manufactured in-house in the UK.

Read more less

Please note: spacers are sold as PAIRS! if you want to do front and rear than qty x2 is needed! Even better driving dynamics and more exciting looks: H&R TRAK+ wheel spacers make your car even sportier! By moving the wheel out from the hub, TRAK+ wheel spacers widen the stance of the vehicle and lower its roll center. This simple modification increases lateral stability, which in turn provides improved handling, greater safety and of course, the sleek style you’ve been looking for. Like all of H&R’s street-engineered products, H&R TRAK+ wheel spacers are certified by the German Technical Inspection Agency (TÜV). H&R also has the correct wheel bolts or nuts to install TRAK+ wheel spacers on most cars, with original or aftermarket wheels. 40mm overall Axle spacers High strength, light weight aluminum/magnesium alloy CNC machined Anodized for optimum corrosion protection Available for most domestic and imported automobiles For use with original or aftermarket wheels (Studs may need shortening if aperture in rear of alloy wheel is not sufficient for clearance) Compatible with all suspension designs TUV approved SPECIFICATIONS Track widening per axle [mm] 40 Thickness [mm] 20 Number of Holes 5.0 Bolt Hole Circle Ø [mm] 112 Centering Diameter [mm] 57.1 Colour Black Registration Type with TÜV® certificate   Please note, Due to the nature and complexity of a wheel spacer, customers MUST know that the size they are ordering is correct prior to ordering by measuring your stud length and wheel groove depth. Unfortunately, if over tightened the integrity of the spacer and / or bolts can be compromised - and due to this, any spacer that has been fitted, trial fitted or removed from its packaging can not be returned! Please be aware of this as by ordering you agree to this!

Read more less

Make Model Sub-Model Engine Engine Type BHP Year Special Comments Front Brake Caliper Type SEAT Leon (KL) 1.0 Turbo 90 2020- TRW SEAT Leon (KL) 1.0 Turbo 110 2020- TRW SEAT Leon (KL) 1.4 Turbo Hybrid 204 2020- TRW SEAT Leon (KL) 1.5 Turbo 130 2020- TRW SEAT Leon (KL) 1.5 Turbo 150 2020- TRW SEAT Leon (KL) 1.5 Turbo and Electric 150 2020- TRW SEAT Leon (KL) 2.0 Turbo 190 2021- TRW SEAT Leon (KL) 2.0 Turbo Diesel 115 2020- TRW SEAT Leon (KL) 2.0 Turbo Diesel 150 2020- TRW

Read more less

This performance intake kit is designed to fit the Volkswagen, Audi, Seat and Skoda with 1.5 / 1.0 TSI engines Features Improves performance and throttle response Enhanced induction and turbo sound Full fitting kit and instructions Mounts to standard factory mounting points and rubbers Easy to clean using our filter maintance kit - CK-003 What Will I Get? Ramair Filters utilise the top-quality components in all their kits see below for what this kit will include: Black powder coated heat shield Ramair foam filter Black silicone intake pipe Full fitting kit with easy step by step instructions Fitment Compatibility Chart This product fits the following: Year Make Model Engine 2017-2021 Skoda Octavia (MK3) 1.5 TSI 2018-2021 Audi Q2 (GA) 1.5 TSI 2018-2021 Audi A1 (GB) 1.5 TSI 2018-2021 Audi Q3 (F3) 1.5 TSI 2018-2021 Seat Arona (KJ) 1.5 TSI 2018-2021 Seat Ateca (KH) 1.5 TSI 2018-2021 Seat Leon (MK3) 1.5 TSI 2020-2025 Seat Leon (MK4) 1.5 TSI 2018-2021 Seat Tarraco (KN2) 1.5 TSI 2018-2021 Seat Ibiza (6F) 1.0 MPI 2018-2021 Seat Ibiza (6F) 1.5 TSI 2017-2021 Skoda Kamiq (NW) 1.5 TSI 2017-2021 Skoda Karoq (NU7/ND7) 1.5 TSI 2017-2021 Skoda Scala (NW) 1.5 TSI 2017-2021 Skoda Kodiaq (NS) 1.5 TSI 2017-2021 Skoda Superb (MK3) 1.5 TSI 2017-2021 VW Arteon (3H) 1.5 TSI 2020-2025 VW Golf (MK8) 1.5 eTSI 2020-2025 VW Golf (MK8) 1.5 TSI 2020-2021 VW T-Cross (MK1) 1.5 TSI 2017-2021 VW T-Roc (MK1) 1.5 TSI 2017-2021 VW Golf (MK7) 1.5 TSI 2017-2021 VW Touran (MK2) 1.5 TSI 2017-2021 VW Tiguan (AD/BW) 1.5 TSI 2017-2021 VW Tiguan Allspace (AD/BW) 1.5 TSI 2017-2021 VW Polo (AW) 1.0 MPI 2017-2021 VW Polo (AW) 1.5 TSI 2017-2021 VW Passat (3G) 1.5 TSI 2017-2021 Audi A3 (8V) 1.5 TFSI 2017-2021 Audi A3 (8V) 1.5 TSI 2020-2021 Audi A3 (8Y) 1.5 TSI 2020-2023 VW Caddy (MK4) 1.5 TFSI 2020-2023 VW Caddy (MK5) 1.5 TFSI  

Read more less

This performance intake kit is designed to fit the MQB Volkswagen, Audi, Seat, Skoda and Cupra that have the 2.0 TDI/GTD engine. Features An open air induction kit will give your car that ever needed increase in induction.  80mm intake diameter Will give the vehicle an increase in BHP and more importantly torque. Optimise airflow and filtration by utilising the twin-tangential velocity stack that brings smooth air flow and the nanofibre filtration media. Easy to clean using our filter maintance kit - CK-003 What Does It Do? This induction kit will increase the airflow into the turbo while increasing engine noise over the restrictive factory air intake system. This kit includes everything required for the fitting of the induction kit. What Will I Get? Ramair Filters utilise the top-quality components in all their kits see below for what this kit will include: Black heat shield Ramair foam air filter Black silicone hose  Full fitting kit with easy step by step instructions Fitment Compatibility Chart This product fits the following: Year Make Model Engine 2019-2025 Audi A3 (8Y) 2.0 TDI 2020-2025 VW Caddy (MK4) 2.0 TDI 2021-2025 Cupra Formentor (KM7) 2.0 TDI 2020-2025 VW Golf (MK8) 2.0 TDI 2020-2025 VW Golf GTD (MK8) 2.0 TDI 2019-2025 Seat Leon (MK4) 2.0 TDI 2019-2025 Skoda Octavia (MK4) 2.0 TDI 2019-2025 Skoda Octavia VRS (MK4) 2.0 TDI 2022-2025 Ford Transit Connect 2.0 EcoBlue

Read more less

VWR 'Cup Edition' EVO 8.5 x 18" Alloy Wheels RacingLine's 'Cup Edition' EVO 8.5 x 18" alloy wheel has been developed for our track and race cars to give a track-orientated rim that's both ultra-strong yet light. Why choose 'Cup Edition' EVO? The VWR ‘Cup Edition’ EVO 18" Alloy Wheel has been a favourite for a decade for race and track cars to deliver an ultra-strong yet lightweight rim capable of repeatedly coping with the extreme demands that track driving brings. Developed direct from our racing programme, this exact family of VWR 'Cup Edition' EVO Alloy Wheels is based on the rims used in the Volkswagen Racing Cup and the British Touring Car Championship.  Now, our Cup Edition EVO wheel updates this classic design with lighter weight, a fresh new appearance and stunning detailing. The perfect track dimensions for MQB/MQBE of 8.5 x 18" diameter with an ET45 offset. Finished in a choice of stunning hard-wearing Satin Gunmetal Grey, Gloss Black, Matte Bronze or Motorsport White, all complete with RacingLine centre cap. Produced to the highest standards, developed and manufactured to exceed OEM standards. PERFECT FITMENT Fitment offset of ET45 for many VWG models on MQB, MQB EVO and A5 platforms with 5x112 PCD. LIGHT : STRONG Weighing 9.7kg / 21.3lbs per wheel, whilst crucially still retaining the strength needed for the demands of road or track. IDEAL FOR TRACK The choice of 18" rim is ideal for track use, allowing a higher, squarer tyre fitment without the risk of excessive rubbing. Precision engineered for Perfect Performance. Max. wheel load of 560kg tested to ISO 7141 for geometric accuracy, impact strength, structural fatigue and load rating requirements Knurled bead seats to prevent tyre slip/rotation Weight removed from the mounting face including drainage cutouts to ensure no trapped water or debris between wheel and hub face causing long term corrosion Choice of four durable finishes to look good, and stay looking good Confirmed applications. Fitment for all VWG models on MQB, MQB EVO and A5 platforms with 5x112 PCD: VWR610008 18 x 8.5 ET45 Gunmetal Grey   VWR610009 18 x 8.5 ET45 Motorsport White​ ​VWR610010 18 x 8.5 ET45 Gloss Black   VWR610011 18 x 8.5 ET45 Matte Bronze For motorsport use (eg. for vehicles with additional camber for arch clearance) we also offer an ET35 offset in Gunmetal Grey. VWR610100 18 x 8.5 ET35 Gunmetal Grey > VW Golf 8 2020+ > VW Golf 7 & 7.5 2013-2020 > VW Passat B8 2015+ > VW Arteon 2017+ > VW T-Roc 2017+ > VW Tiguan II 2016+ > VW Golf 5 2005-2008 > VW Golf 6 2008-2014 > VW Scirocco 2008-2017 > VW Jetta / GLI 5 2005-2011 > VW Jetta / GLI 6 2011-2018 > VW Jetta / GLI 7 2018+ > Audi S3 8Y 2020+ > Audi A3 8Y 2020+ > Audi S3 8V 2013-2020 > Audi A3 8V 2013-2020 > Audi RS3 2.5 TFSI 8V 2015-2017 > Audi TT 3 8S 2014+ > Audi SQ2 2018+ > Audi S3 8P 2006-2012 > Audi A3 8P 2003-2012 > Audi TT II 8J 2006-2014 > Cupra Leon IV FW 2020+ > SEAT Leon III 5F 2015-2020 > SEAT Leon II 1P 2005-2012 > Cupra Formentor 2020+ > Cupra Ateca 2018+ > Skoda Octavia IV NX 2020+ > Skoda Octavia III 5E 2014-2020 > Skoda Octavia II 1Z 2004-2013   Strength matters. With a load rating of 560kg per wheel, these Cup Edition EVO wheels have the strength to cope with repeated, harsher track use.  It's essential for the rim to have this sort of strength engineered-in from the start. Just imagine the 'spike loads' running through a wheel hitting circuit kerbing (such as sausage kerbs) through a corner at speed. Obsessive weight saving. We've put a lot of development time into weight reduction, but without compromising strength. Incorporating cut-outs in the mounting face, material removal in the front and back of each spoke, even a groove running around the outer rim to save a few more grams. ​Knurled tyre bead seat. Another nice new feature incorporated into the design are knurled strips on the outer barrel of the wheel where the tyre bead seats.    A true motorsport feature that prevents unwanted tyre slip or rotation on the rim in extreme use. The result? 9.7kg / 21.3lbs per wheel, yet still retaining a load rating of 560kg.

Read more less

This is for UK Registration Plates only (Metal Pressed Plates & Euro Plates will not fit) Brand new to CEUK - the PlexiClick® Invisible Number plate holder system! Perfect for those who do not wish to drill their number plates or have big ugly framed number plate holders! Also perfect for those who swap their number plate for a show plate at events! Transform your vehicle with the PLEXICLICK Frameless Number Plate Holder Clips – the ideal combination of style, practicality, and durability. These frameless, clear clips are designed for quick and easy installation, providing a secure fit for your front and rear license plates without the need for drilling. Perfect for cars, vans, and other UK vehicles, these clips offer a clean, modern look with excellent performance. Whats in the kit? 4x Plexiclick® V3 for mounting two UK license plates 8x screws for fixing the clips to your vehicle 4x Anti Vibration Rubber Bungs 1x Instruction Manual Key Specifications: Material: Premium quality, weather-resistant plastic Fitment: Universal for UK standard license plates (front & rear) Color: Clear, frameless design Installation: Number plate just clicks into place and can be removed easily  

Read more less

Price is for one strut / prop Product can be used on Bonnets (Hoods) / Boot (Trunks) and Doors Pro Props Carbon Fibre Bonnet Prop Introducing the Pro-Prop, the ultimate finishing touch for your car at shows. Manufactured in the UK, this lightweight and secure carbon fibre bonnet prop (hood prop) is specifically designed for display purposes. Its sturdy construction makes it perfect for holding bonnets open, whether or not your vehicle has gas lift struts. Crafted from the lightest genuine carbon fibre tubing and featuring precision-machined billet aluminium components with stainless steel fixings, the Pro-Prop offers both functionality and a sleek, professional appearance. Shaft Made from genuine carbon fibre, the shaft is ultra-thin and lightweight, with no wrapping or skinning—this is the real deal. Upper Fixing Precision CNC machined from billet aluminium, the upper fixing ensures a premium finish while maintaining lightweight properties. It includes a tactile thumb screw to securely attach the prop to your vehicle’s bonnet hook. Lower Fixing Also precision CNC machined from billet aluminium, the lower fixing houses a 304 stainless steel hook, allowing you to lock it into your vehicle’s latch system. This lower hook offers up to 45mm of vertical adjustment for a perfect fit. Once fitted, the Pro-Prop remains secure. To disengage, simply release your bonnet as usual, and then store the prop in the supplied tube for safekeeping until your next show or meet. Sizing Length of Carbon Section only: 550mm / 55cm Total length of all parts: 670mm / 67cm Adjustment Capability: 50mm / 5cm (Taking total to possible 720mm / 72cm)

Read more less

Introducing the Enhanced Edition LED H7 Mini All the Power & Brightness of our V3 Bulb, but without the bulk! This bulb will fit in ANY H7 Fitments and replaces the OEM lamp unit for an ultra bright replacement. This bulb can be used as a dipped & high beam upgrade as well as a foglight. Vision, Without Restriction The output on these bulbs is truly phenomenal, whilst the latest technology and components allows for superior output without damaging OEM Components. Designed to fit as any OEM part would, but offering a a higher lumen output. We've managed to micro size the cooling fan and move it into the shaft of the bulb, which means the removal of the bulky heat fade on the rear of the bulb and allowing for fitment in tight areas just like oem! No longer any need for clips & caps! The bulb is designed to fit in any H7 fixing without any adjustments or additional items, and utilising its 4 point technology, this can be orientated in either 2 or 4 location points to ensure the best output and zero polarity issues! Specs: Voltage - 12v Wattage - 28w LED Chip - 3570 Colour Temp - 6000k Ice White Lumen - 6000Lm Per Bulb Will fit in any vehicle which takes a H7 fitting  Good to know. High Lumen Output (6000lm Per Bulb) Improved visibility in the evenings Reduced strain on the eyes suitable for use in all builds of headlamps Suitable for projector and reflector headlamps What's in the box 2x H7 LED Units (6000k Default) Warranty: The product is provided with a 12 Months guarantee as standard, Unless stated on the product packaging. If the packaging states more than 12 months, the product packaging must be kept to retain the extended warranty. Vehicle Fitment: Some vehicles may use different types of bulbs depending on spec levels - For example, a special edition vehicle (Such as Ford "ST" or VW "GTi") may have a different light unit to a standard spec. If this item is listed on your vehicle catergory please confirm that it is the correct fitment for your vehicle by checking your item prior to ordering. The installation of LED's may trigger a Dashboard Error Message which is a harmless side effect of lower powered units, if this occurs for you please refer to our FAQ's. 

Read more less

Description Introducing the Enhanced Edition LED H8/11 Fog Bulb Mini All the Power & Brightness of our V3 Bulb, but without the bulk! This bulb will fit in both H8 and H11 Fitments and replaces the OEM fog light unit for an ultra bright replacement. This bulb can also be used as a dipped & high beam upgrade  Vision, Without Restriction The output on these bulbs is truly phenomenal, whilst the latest technology and components allows for superior output without damaging OEM Components. Designed to fit as any OEM part would, but offering a a higher lumen output. We've managed to micro size the cooling fan and move it into the shaft of the bulb, which means the removal of the bulky heat fade on the rear of the bulb and allowing for fitment in tight areas just like oem! Specs: Voltage - 12v Wattage - 28w LED Chip - 3570 Colour Temp - 6000k Ice White Lumen - 6000Lm Per Bulb Will fit in any vehicle which takes a H8 or H11 fitting  Good to know. High Lumen Output (6000lm Per Bulb) Improved visibility in the evenings Reduced strain on the eyes suitable for use in all builds of headlamps Suitable for projector and reflector headlamps What's in the box 2x H8/11 LED Units (6000k Default) Warranty: The product is provided with a 12 Months guarantee as standard, Unless stated on the product packaging. If the packaging states more than 12 months, the product packaging must be kept to retain the extended warranty. Vehicle Fitment: Some vehicles may use different types of bulbs depending on spec levels - For example, a special edition vehicle (Such as Ford "ST" or VW "GTi") may have a different light unit to a standard spec. If this item is listed on your vehicle catergory please confirm that it is the correct fitment for your vehicle by checking your item prior to ordering. The installation of LED's may trigger a Dashboard Error Message which is a harmless side effect of lower powered units, if this occurs for you please refer to our FAQ's. 

Read more less

For hydraulic brake and clutch systems. Meets and exceeds the current international specifications of U.S. FMVSS No. 16 DOT 4, SAE J1703 and ISO 4925 (Class 3) Suitable for use in passenger cars, commercial vehicles and motorcycles with hydraulic brake systems and clutch systems; recommended where a non-petroleum-based medium has to be used. Not suitable for vehicles with mineral oil-based systems (e.g. certain Citroen models). If in doubt, consult the vehicle manual. Min. dry boiling point 260°C. Min. wet boiling point 165°C Notice Keep brake fluid clean and dry. Contamination by dirt, water, petroleum products or other materials can lead to brake failure or costly repairs. Store brake fluid only in its original container. Keep the container clean and tightly closed to prevent the accumulation of water. Do not refill the container and do not use it to store any other liquids. Dispose of used brake fluid responsibly (EU waste code 160113). Brake fluid damages paintwork – if spilled, wash off immediately using plenty of water.  DOT 4 Technical Info Contents 500 ml Colour Pale Amber Chemical basis Butoxyethanol Shelf life from production 36 Month Min. wet boiling point 165 °C Min. dry boiling point 260 °C Density 1.052 g/ml Density conditions at 20°C pH value 7-11

Read more less

Compatible for: Audi -A1  A1 25/30 1.0 TSI/TFSI 2022- (GB) -A3 1.0 TSI (2022-) -Q2 1.0 TSI (2022-) Seat -Arona 1.0 TSI (2022-) -Ateca 1.0 TSI (2022-) -Ibiza    Mk5 (KJ) 2017 - late 2021  1.0 TSI              Mk5 (KJ) 2021-  1.0 TSI -Leon Mk4 2022-  1.0 TSI Skoda -Fabia PJ 2022- 1.0 TSI -Kamiq  1.0 TSI (2022-) -Karoq 1.0 TSI (2022-) -Octavia 1.0 TSI (2022-) -Scala 1.0 TSI (2022-) Volkswagen -Golf MK8  1.0 TSI (2022-) -Polo 1.0 TSI (2022-) -T-Cross 1.0 TSI (2022-) -T-Roc 1.0 TSI (2022-) -Taigo 1.0 TSI (2022-)   FMINDK52 is the Forge Motorsport cold air induction system for the 2022 onwards 1.0 TSI engine found in a large selection of vehicles from the VW, Audi, Skoda, and Seat range. With the highly successful FMINDK30 and FMINDK39 induction kits for the previous generation 1.0 TSI VAG vehicles there has been a large demand for Forge Motorsport to develop an improved air intake system for the latest VAG power unit.  As with all manufacturers in recent times, the need to make smaller capacity engines more powerful with better efficiency has been their top priority. To achieve these goals, the OEM design engineers must maximise the space to its fullest, which in turn creates more of a challenge for the aftermarket manufacturers and tuners to improve what is already fitted to the vehicle. Nonetheless, this has not stopped us at Forge Motorsport! Even with plenty of expertise from past developments with the previous small capacity VAG engines, this new power unit needed an extensive amount of testing time to ensure we produced a product that provided genuine improvements over the standard air box.  The CAD designed, laser cut, and precision folded heat shield is designed to form a barrier between the air inlet tract and radiant heat from the engine. It also helps duct the cold air to the air filter, to preserve low intake temperatures, which in-turn creates more power. Finished in our black textured powder coating, this creates a product with an OEM look and quality. This kit is offered with our Forge high flow, pleated, synthetic nanofiber filtration filter, which has been manufactured for optimum size and fit to the available space giving superior flow and filtration with enhanced breathing for the 1.0 turbo charged engine.   Alternatively, there is our foam filter option available soon that has been exclusively manufactured by Pipercross. During dyno testing we tried several filter options and we found that neither filter excelled over the other with results being almost identical throughout the rev range. Both the filters offered can be oiled by the end user to prevent fine dust commonly found in hot climates from entering the inlet tract. Testing was completed using Performance Remap in Gloucester with their VTEC 4 wheel drive dynamometer. This was to ensure all our data has been achieved with results as accurately as possible by an independent tuner.  The dyno graph below shows torque gains at 2600RPM all the way to redline, with a gain of nearly 10NM from between 3000RPM and 3500RPM. This gain is very beneficial as it is consistently higher than stock from turbo spool up through to full boost, resulting in noticeably sharper acceleration and a more exhilarating experience for the driver, as typically this is where true power gains can be felt when behind the wheel.   The Forge Motorsport induction kit FMINDK52 includes all the necessary hardware and step by step installation instructions for any car enthusiast with basic garage tools to fit at home, in just a couple of hours!  

Read more less

This product CAN NOT be used in conjunction with FMTIA13 FMINLH26 is our replacement intake hose for the 2022- VAG 1.0 TSI engine. This is a direct replacement for the original plastic inlet hose. This is a simple fitment which replaces the entire restrictive rear factory plastic ‘bellows’ pipe between the airbox and the turbocharger inlet.  Constructed from reinforced high quality 5 ply silicone, this hose offers increased rigidity to prevent deformation from engine movement or heat cycles. This product is offered in two colours, gloss black or bright red, so this hose is not only functional but it also improves the aesthetics of the TSI engine bay. Audi -A1  A1 25/30 1.0 TSI/TFSI 2022- (GB) -A3 1.0 TSI (2022-) -Q2 1.0 TSI (2022-) Seat -Arona 1.0 TSI (2022-) -Ateca 1.0 TSI (2022-) -Ibiza    Mk5 (KJ) 2017 - late 2021  1.0 TSI              Mk5 (KJ) 2021-  1.0 TSI -Leon Mk4 2022-  1.0 TSI Skoda -Fabia PJ 2022- 1.0 TSI -Kamiq  1.0 TSI (2022-) -Karoq 1.0 TSI (2022-) -Octavia 1.0 TSI (2022-) -Scala 1.0 TSI (2022-) Volkswagen -Golf MK8  1.0 TSI (2022-) -Polo 1.0 TSI (2022-) -T-Cross 1.0 TSI (2022-) -T-Roc 1.0 TSI (2022-) -Taigo 1.0 TSI (2022-)   This product takes about 10 minutes to install and like all our silicone products, is covered by our lifetime warranty.

Read more less

  Similar to many of the newer VAG engines, the latest 1.0 TSI power plant is not equipped with a diverter valve fitted as standard, Forge Motorsport has developed a twin piston dump valve that not only gives you a loud audible sound when lifting off the throttle, but also increases the throttle response during gear changes by reducing turbo lag. It has been designed to help the turbocharger maintain its rotational speed ready for when you accelerate, whilst also taking the strain away from the impeller. Without removing this stress from your turbo, it can lead to premature failure especially on remapped engines and modified vehicles.       This valve kit allows the fitment of our fast response blow off valve preventing turbo surge and prolonging the life of your engine’s turbocharger. The kit includes all the necessary hardware and step by step installation instructions for any car enthusiast with appropriate garage tools to fit at home, in just a couple of hours!  Due to the exposed position of the OEM boost pipe and the nature of heat cycle, the plastic that the OEM pipe is made from can deteriorate over time, becoming brittle and susceptible to boost leaks. This kit totally replaces this plastic pipe from turbo to manifold with a multi-ply silicone hose (available in a choice of red or black). Highlights: CNC machined billet couplers and components CNC machined twin piston Forge valve. Two hose options: red or black (Custom colours available but will incur a 50% non-refundable deposit and a lead time of 8-10 weeks) Forge Motorsports dump valve will not bring on any check engine lights (EML)  The hose has a quality inner lining of modified silicone known as 'Fluorosilicone'. This means that the hose will stay bright and vibrant and will not deteriorate over time. Forge Motorsport lined hoses are suitable to be used with modern long-life coolants, Organic Acid Technology coolants (O.A.T.) and oil mist. The construction of the hose has been engineered to exceed that of the OEM fitments, the Forge Motorsport hose will enhance any engine bay both technically and aesthetically. We cannot guarantee that this product will fit with all aftermarket intakes. Lifetime warranty We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner Audi-A1 A1 GB 25/30 1/0 TSI (2022-)-A3 1.0 TSI (2022-)-Q21.0 TSI (2022-) A1A1 (GB) 25/30 1.0 TSI (2022-) A31.0 TSI (2022-) Q21.0 TSI (2022-) Seat Arona 1.0 TSI (2022-) Ateca 1.0 TSI (2022-) Ibiza Mk5 (KJ) 2017 - late 2021 1.0 TSI Mk5 (KJ) 2021- 1.0 TSI Leon Mk4 2022- 1.0 TSI Skoda Fabia PJ 2022- 1.0 TSI Kamiq 1.0 TSI (2022-) Karoq 1.0 TSI (2022-) Octavia 1.0 TSI (2022-) Scala 1.0 TSI (2022-) Volkswagen Golf MK8 1.0 TSI (2022-) Polo 1.0 TSI (2022-) T-Cross 1.0 TSI (2022-) T-Roc 1.0 TSI (2022-) Taigo 1.0 TSI (2022-) This part will take approximately 1 hour to fit.  

Read more less

REAR UPPER WISHBONE INNER BUSH PFR85-514   OEM Part Number: Arm = 5Q0505323D / 5Q0 505 323 D OEM Part Number: Arm = 1K0505323N / 1K0 505 323 N --- REAR UPPER WISHBONE INNER BUSH PFR85-514BLK   OEM Part Number: Arm = 5Q0505323D / 5Q0 505 323 D OEM Part Number: Arm = 1K0505323N / 1K0 505 323 N --- fits: Audi A1 Quattro (2013), Audi S1 8X (2015 on), Audi A3 inc Quattro MK2 8P (2003-2012), Audi RS3 MK2 8P (2011-2013), Audi S3 MK2 8P (2006-2012), Audi A3 / S3 MK3 8V 125PS plus (2013 - 2020) Multi Link, Audi RS3 MK3 8V (2015 - 2020), Audi A3 / S3 MK4 8Y Quattro (2020 on), Audi A3 MK4 8Y FWD (2020 on) Multi-Link, Audi RS3 MK4 8Y (2020 on), Seat Alhambra MK2 (2010 - ON), Seat Ateca Multi-Link (2016-ON), Volkswagen Beetle A5 Multi-Link (2011 - ON), Volkswagen Bora A5 (1K) (2005-2010), Seat Formentor 2WD, Seat Formentor 4WD, Volkswagen Golf MK6 inc R 5K (2009-2012), Volkswagen Golf MK5 1K, Volkswagen Golf Mk5 GTI & R32, Volkswagen Golf Plus 5M, Volkswagen Golf MK7 5G 2WD 122PS plus Multi-link, Volkswagen Golf MK7 5G 4WD inc R, Volkswagen Golf MK7 GTE, Volkswagen Golf Mk8 2wd Multi-Link, Volkswagen Golf R Mk8 4WD, Volkswagen Jetta MK6 A6 Multi-Link (2011 - 2018), Volkswagen Jetta MK7 A7 Multi-Link (2018-ON), Volkswagen Jetta MK5 A5 1K (2005-2010), Seat Leon MK3 5F 150PS plus (2013-2020) Multi Link, Seat Leon KL 4WD, Seat Leon KL Multilink, Seat Leon Mk2 1P (2005-2012), Skoda Octavia Mk2 1Z (2004-2012), Skoda Octavia NX 4WD, Skoda Octavia NX Multilink, Volkswagen Passat B6 & B7 Typ3C (2006-2013), Volkswagen Passat B8 (2013 on), Volkswagen Passat CC 35 (2008-2012), Audi Q2 4WD Quattro MULTI LINK, Audi Q3 8U, Audi RSQ3 8U,  Audi Q3 F3, Audi RSQ3 F3, Volkswagen Scirocco MK3 (2008 - 2017), Seat Altea 5P (2004-), Seat Tarraco (2018-), Volkswagen Sharan MK2 (2010 - ON), Skoda Kodiaq (2017 - ON), Skoda Yeti 5L (2009 - 2017), Skoda Superb (2009-2010), Skoda Superb (2010 - 2015), Skoda Superb (2015 - ), Volkswagen T-Roc 4-Motion inc R, Volkswagen Tiguan 5N MK1 (2007 - 2017), Volkswagen Tiguan AD/BW MK2 (2017 on), Seat Toledo Mk3 5P (2004-2009), Volkswagen Touran (2003-2015), Volkswagen Touran (2017 - ), Audi TT MK2 8J (2007-2014), Audi TTRS MK2 8J (2009-2014), Audi TT / TTRS Mk3 FV/8S (2014 on), Volkswagen Vento A5 (2005 - 2010), Volkswagen Arteon (2017 on), Volkswagen CC (2012 - 2017), Volkswagen Eos 1F (2006-2016)

Read more less

PFF85-833 PFF85-833 replaces the lower half of the original bush whilst including an insert to fit into and fill the voids in the upper bush to minimise wheel hop and improve gear-shifting. This unique bush has been designed to be fitted without subframe removal and avoids associated wheel alignment costs. . OEM Part Number: 5Q0198037B / 5Q0 198 037 B OEM Part Number: 5Q0198037C / 5Q0 198 037 C OEM Part Number: 5Q0198037F / 5Q0 198 037 F --- FRONT LOWER ENGINE MOUNT HYBRID BUSH (LARGE) - FAST ROAD/TRACK PFF85-833P PFF85-833 replaces the lower half of the original bush whilst including an insert to fit into and fill the voids in the upper bush to minimise wheel hop and improve gear-shifting. This unique bush has been designed to be fitted without subframe removal and avoids associated wheel alignment costs. . OEM Part Number: 5Q0198037B / 5Q0 198 037 B OEM Part Number: 5Q0198037C / 5Q0 198 037 C OEM Part Number: 5Q0198037F / 5Q0 198 037 F --- FRONT LOWER ENGINE MOUNT HYBRID BUSH (LARGE) - TRACK/MSPORT PFF85-833BLK PFF85-833 replaces the lower half of the original bush whilst including an insert to fit into and fill the voids in the upper bush to minimise wheel hop and improve gear-shifting. This unique bush has been designed to be fitted without subframe removal and avoids associated wheel alignment costs. OEM Part Number: 5Q0198037B / 5Q0 198 037 B OEM Part Number: 5Q0198037C / 5Q0 198 037 C OEM Part Number: 5Q0198037F / 5Q0 198 037 F --- FITS: Audi A3 / S3 MK3 8V 125PS plus (2013 - 2020) Multi Link, Audi A3 MK3 8V up to 125PS (2013 - 2020) Rear Beam, Audi A3 / S3 MK4 8Y Quattro (2020 on), Audi A3 MK4 8Y FWD (2020 on) Multi-Link, Audi A3 MK4 8Y FWD (2020 on) Rear Beam, Volkswagen Caddy MK4 Typ SB (2020-ON), Seat Formentor 2WD, Seat Formentor 4WD, Volkswagen Golf MK7 5G 2WD 122PS plus Multi-link, Volkswagen Golf MK7 5G 2WD up to 122PS Rear Beam, Volkswagen Golf MK7 5G 4WD inc R, Volkswagen Golf MK7 GTE, Volkswagen Golf Mk8 2wd Multi-Link, Volkswagen Golf Mk8 2wd Rear Beam, Volkswagen Golf R Mk8 4WD, Volkswagen Jetta MK7 A7 Multi-Link (2018-ON), Volkswagen Jetta MK7 A7 Rear Beam (2018-ON), Skoda Karoq 2WD, Skoda Karoq 4WD, Skoda Karoq Multi-Link, Seat Leon MK3 5F 150PS plus (2013-2020) Multi Link, Seat Leon MK3 5F upto 150PS (2013-2020) Rear Beam, Seat Leon KL 4WD, Seat Leon KL Multilink, Seat Leon KL Rear Beam, Skoda Octavia 5E 150PS plus Multi-link, Skoda Octavia 5E up to 150PS Rear Beam, Skoda Octavia NX 4WD, Skoda Octavia NX Multilink, Skoda Octavia NX Rear Beam, Audi Q2 2WD REAR BEAM, Audi Q2 4WD Quattro MULTI LINK, Audi Q3 F3, Audi RSQ3 F3,  Seat Tarraco (2018-), Skoda Kodiaq (2017 - ON), Skoda Superb (2015 - ), Volkswagen T-Roc 4-Motion inc R, Volkswagen T-Roc FWD Rear Beam, Volkswagen Tiguan AD/BW MK2 (2017 on), Volkswagen Touran (2017 - ), Ford Transit / Tourneo Connect Mk3 (2021 ON), Audi TT / TTRS Mk3 FV/8S (2014 on) Diagram reference 30

Read more less

FRONT WISHBONE FRONT BUSH PFF85-501 For a camber adjustable bush use PFF85-501G. OEM Part Number: Bush = 1K0407182 / 5Q0407182 / 1K0407182A OEM Part Number: Arm = 1K0407152BG (Steel) OEM Part Number: Arm = 8J0407151D (Aluminium) --- FRONT WISHBONE FRONT BUSH PFF85-501BLK   OEM Part Number: Bush = 1K0407182 / 5Q0407182 / 1K0407182A OEM Part Number: Arm = 1K0407152BG (Steel) OEM Part Number: Arm = 8J0407151D (Aluminium) --- FRONT WISHBONE FRONT BUSH CAMBER ADJUSTABLE PFF85-501G This bush features a CNC machined Stainless Steel sleeve with an offset bore that can be rotated using our bespoke tooling (supplied), giving +/- 0.5 degrees of on-car camber adjustment. OEM Part Number: Bush = 1K0407182 / 5Q0407182 / 1K0407182A OEM Part Number: Arm = 1K0407152BG (Steel) OEM Part Number: Arm = 8J0407151D (Aluminium) --- FRONT WISHBONE FRONT BUSH CAMBER ADJUSTABLE PFF85-501GBLK This bush features a CNC machined Stainless Steel sleeve with an offset bore that can be rotated using our bespoke tooling (supplied), giving +/- 0.5 degrees of on-car camber adjustment. OEM Part Number: Bush = 1K0407182 / 5Q0407182 / 1K0407182A OEM Part Number: Arm = 1K0407152BG (Steel) OEM Part Number: Arm = 8J0407151D (Aluminium) --- FITS: Audi A3 inc Quattro MK2 8P (2003-2012), Audi RS3 MK2 8P (2011-2013), Audi S3 MK2 8P (2006-2012), Audi A3 / S3 MK3 8V 125PS plus (2013 - 2020) Multi Link, Audi A3 MK3 8V up to 125PS (2013 - 2020) Rear Beam, Audi RS3 MK3 8V (2015 - 2020), Audi A3 / S3 MK4 8Y Quattro (2020 on), Audi A3 MK4 8Y FWD (2020 on) Multi-Link, Audi A3 MK4 8Y FWD (2020 on) Rear Beam, Audi RS3 MK4 8Y (2020 on), Seat Alhambra MK2 (2010 - ON), Seat Ateca Multi-Link (2016-ON), Seat Ateca Rear Beam (2016-ON), Volkswagen Beetle A5 Multi-Link (2011 - ON), Volkswagen Beetle A5 Rear Beam (2011 - ON), Volkswagen Bora A5 (1K) (2005-2010), Volkswagen Caddy Mk3 Typ 2K (2004 - 06/2010), Volkswagen Caddy Mk3.5 Typ 2K (06/2010 - 2020), Volkswagen Caddy MK4 Typ SB (2020-ON), Seat Formentor 2WD, Seat Formentor 4WD, Volkswagen Golf MK6 inc R 5K (2009-2012), Volkswagen Golf MK5 1K, Volkswagen Golf Mk5 GTI & R32, Volkswagen Golf Plus 5M, Volkswagen Golf MK7 5G 2WD 122PS plus Multi-link, Volkswagen Golf MK7 5G 2WD up to 122PS Rear Beam, Volkswagen Golf MK7 5G 4WD inc R, Volkswagen Golf MK7 GTE, Volkswagen Golf Mk8 2wd Multi-Link, Volkswagen Golf Mk8 2wd Rear Beam, Volkswagen Golf R Mk8 4WD, Volkswagen Jetta MK6 A6 Multi-Link (2011 - 2018), Volkswagen Jetta MK6 A6 Rear Beam (2011 - 2018), Volkswagen Jetta MK7 A7 Multi-Link (2018-ON), Volkswagen Jetta MK7 A7 Rear Beam (2018-ON), Volkswagen Jetta MK5 A5 1K (2005-2010), Skoda Karoq 2WD, Skoda Karoq 4WD, Skoda Karoq Multi-Link, Seat Leon MK3 5F 150PS plus (2013-2020) Multi Link, Seat Leon MK3 5F upto 150PS (2013-2020) Rear Beam, Seat Leon KL 4WD, Seat Leon KL Multilink,  Seat Leon KL Rear Beam, Seat Leon Mk2 1P (2005-2012), Skoda Octavia Mk2 1Z (2004-2012), Skoda Octavia 5E 150PS plus Multi-link, Skoda Octavia 5E up to 150PS Rear Beam, Skoda Octavia NX 4WD, Skoda Octavia NX Multilink, Skoda Octavia NX Rear Beam, Volkswagen Passat B6 & B7 Typ3C (2006-2013), Volkswagen Passat B8 (2013 on), Volkswagen Passat CC 35 (2008-2012), Audi Q2 2WD REAR BEAM, Audi Q2 4WD Quattro MULTI LINK, Audi Q3 8U, Audi RSQ3 8U, Audi Q3 F3, Audi RSQ3 F3, Volkswagen Scirocco MK3 (2008 - 2017), Seat Altea 5P (2004-), Seat Tarraco (2018-), Volkswagen Sharan MK2 (2010 - ON), Skoda Kodiaq (2017 - ON), Skoda Yeti 5L (2009 - 2017), Skoda Superb (2009-2010), Skoda Superb (2010 - 2015), Skoda Superb (2015 - ), Volkswagen T-Roc 4-Motion inc R, Volkswagen T-Roc FWD Rear Beam, Volkswagen Tiguan 5N MK1 (2007 - 2017), Volkswagen Tiguan AD/BW MK2 (2017 on), Seat Toledo Mk3 5P (2004-2009), Volkswagen Touran (2003-2015), Volkswagen Touran (2017 - ), Ford Transit / Tourneo Connect Mk3 (2021 ON), Audi TT MK2 8J (2007-2014), Audi TTRS MK2 8J (2009-2014), Audi TT / TTRS Mk3 FV/8S (2014 on), Volkswagen Vento A5 (2005 - 2010), Volkswagen Arteon (2017 on), Volkswagen CC (2012 - 2017), Volkswagen Eos 1F (2006-2016)

Read more less

PFC13-14 Made in precision CNC-machined 6082-T6 grade aluminium and anodised Black, with sizes to suit anti-roll bar diameters ranging from 13mm to 33 mm, these easy-to-fit, two-bolt clamps bolt to the side of each anti-roll bar bush to add lateral support and prevent any sidewards movement of the bar itself that might cause inconsistent handling. Size 13-14mm --- PFC15-16 Made in precision CNC-machined 6082-T6 grade aluminium and anodised Black, with sizes to suit anti-roll bar diameters ranging from 13mm to 33 mm, these easy-to-fit, two-bolt clamps bolt to the side of each anti-roll bar bush to add lateral support and prevent any sidewards movement of the bar itself that might cause inconsistent handling. Size 15-16mm --- PFC17-18 Made in precision CNC-machined 6082-T6 grade aluminium and anodised Black, with sizes to suit anti-roll bar diameters ranging from 13mm to 33 mm, these easy-to-fit, two-bolt clamps bolt to the side of each anti-roll bar bush to add lateral support and prevent any sidewards movement of the bar itself that might cause inconsistent handling. Size 17-18mm --- PFC19-20 Made in precision CNC-machined 6082-T6 grade aluminium and anodised Black, with sizes to suit anti-roll bar diameters ranging from 13mm to 33 mm, these easy-to-fit, two-bolt clamps bolt to the side of each anti-roll bar bush to add lateral support and prevent any sidewards movement of the bar itself that might cause inconsistent handling. Size 19-20mm --- PFC21-22 Made in precision CNC-machined 6082-T6 grade aluminium and anodised Black, with sizes to suit anti-roll bar diameters ranging from 13mm to 33 mm, these easy-to-fit, two-bolt clamps bolt to the side of each anti-roll bar bush to add lateral support and prevent any sidewards movement of the bar itself that might cause inconsistent handling. Size 21-22mm --- PFC23-24 Made in precision CNC-machined 6082-T6 grade aluminium and anodised Black, with sizes to suit anti-roll bar diameters ranging from 13mm to 33 mm, these easy-to-fit, two-bolt clamps bolt to the side of each anti-roll bar bush to add lateral support and prevent any sidewards movement of the bar itself that might cause inconsistent handling. Size 23-24mm --- PFC25-27 Made in precision CNC-machined 6082-T6 grade aluminium and anodised Black, with sizes to suit anti-roll bar diameters ranging from 13mm to 33 mm, these easy-to-fit, two-bolt clamps bolt to the side of each anti-roll bar bush to add lateral support and prevent any sidewards movement of the bar itself that might cause inconsistent handling. Size 25-27mm --- PFC28-30 Made in precision CNC-machined 6082-T6 grade aluminium and anodised Black, with sizes to suit anti-roll bar diameters ranging from 13mm to 33 mm, these easy-to-fit, two-bolt clamps bolt to the side of each anti-roll bar bush to add lateral support and prevent any sidewards movement of the bar itself that might cause inconsistent handling. Size 28-30mm --- PFC31-33 Made in precision CNC-machined 6082-T6 grade aluminium and anodised Black, with sizes to suit anti-roll bar diameters ranging from 13mm to 33 mm, these easy-to-fit, two-bolt clamps bolt to the side of each anti-roll bar bush to add lateral support and prevent any sidewards movement of the bar itself that might cause inconsistent handling. Size 31-33mm

Read more less

Racingline RP700 Rear Brake Pads - For MQB Evo Models with 310mm Rear Disc Setup Our new RP700 Brake Pads are replacement brake pads for cars using the standard brake hardware, with applications for multiple MQB (and some other) performance models. Drive your car hard and the chances are you’ve experienced brake fade at some point. That’s where our High Performance RP700 Brake Pads come in. Using an advanced high friction material, these new pads provide a dramatic improvement in the braking department.  A straight replacement for the factory pads using the standard brakes, yet delivering a much higher resistance to high temperature fade.   Fits : Volkswagen/ArteonVolkswagen Golf Mk8Audi A3 (8Y 2020-)Audi RS3 (8Y)Audi S3 (8Y)SEAT Leon Mk4Skoda Octavia Mk4

Read more less

DIAGRAM REFERENCE: 21PRODUCT NOTES: PFF3-1325 Lower Torque Mount Bushis made from our stiffestBlack 95Amaterial to provide a durable replacement for the factory rubber bush to give road or tuned vehicles a sharper throttle response and more positive gear-change without compromising ride quality and NVH. An increase in stiffness by 50% over the worn OE rubber bush helps to reduce excessive engine movement caused by the torque reaction of the engine during acceleration and deceleration, one of the biggest causes of wheel-hop on tuned FWD or front-engined vehicles. Please check which type of bracket is fitted to the vehicle before ordering. See the part numbers above and photos below for reference.BUSH SIZE IF APPLICABLE:NUMBER OF BUSHES IN PACK:1REPLACES OEM BUSH PART NUMBERS:5Q0199855J/5Q0199855Q/5Q0199855PRoad SeriesFor Road and fast Road usePOWERFLEX Road Series bushes improve your cars road holding and chassis performance by controlling the amount of unwanted flex in the suspension. They offer Prolonged tyre life, Improved performance, Increased safety, Greater cost-effectiveness.   Shop By Car/Volkswagen/Passat B8 Shop By Car/Volkswagen/Tiguan (Mk2) Shop By Car/Audi/S3 (8V)/Bushes by Powerflex Shop By Car/SEAT/Ateca Shop By Car/Audi/Q2 Shop By Car/Volkswagen/Golf Mk7/Bushes by Powerflex Shop By Car/SEAT/Tarraco Shop By Car/Skoda/Karoq Shop By Car/Skoda/Kodiaq Shop By Car/Volkswagen/T-Roc Shop By Car/Skoda/Octavia Mk3 (5E)/Bushes by Powerflex Shop By Car/Skoda/Superb (3V 2015-) Shop By Car/Audi/A3 (8V 12-20)/Bushes by Powerflex Shop By Car/Audi/TT Mk3 (8S)/Bushes by Powerflex Shop By Car/SEAT/Leon Mk3 (5F)/Bushes by Powerflex Shop By Car/Volkswagen/Touran (Mk2 15-) Shop By Car/Audi/Q3 (Mk2 18-) Shop By Car/SEAT/Leon Mk4 Shop By Car/Skoda/Octavia Mk4 Shop By Car/Audi/RSQ3  

Read more less

  The APR Open PEX intake system is the best price/performance intake system on the market and has already been installed thousands of times in vehicles.The sound and performance of the engine were significantly increased and the restrictive area in the intake tract was eliminated. This made it possible to reduce the pressure loss and increase the efficiency of the turbocharger while doing the same work. This results in more power and torque while reducing load. The system uses a washable 7-inch and very high quality conical cotton filter that has a 4-inch connection.This was also necessary to reduce the standard pressure drop and maximize the airflow while also significantly increasing the sound aspect. The PEX material conducts heat very poorly, which also benefits the system and therefore ideally contributes to increasing performance.The PEX material still gives the engine compartment a touch of stock component, as far as you can say for an open air filter. The material also offers the advantage that almost any design can be realized. This made it possible to create an extremely complex and organic shape of the heat shield, which can effectively shield the hot air from below. Features: Improved intake noise Reduction of pressure loss Increases the efficiency of the turbocharger ore power and torque High quality cotton filter Airflow is maximized Made from PEX material FITS: Shop By Car/Volkswagen/Passat B8 Shop By Car/Volkswagen/Tiguan (Mk2) Shop By Car/Volkswagen/Arteon Shop By Car/Volkswagen/Golf Mk7 Shop By Car/Volkswagen/Golf Mk8 Shop By Car/Skoda/Octavia Mk3 (5E) Shop By Car/Skoda/Superb (3V 2015-) Shop By Car/Audi/A3 (8Y 2020-) Shop By Car/Audi/A3 (8V 12-20) Shop By Car/SEAT/CUPRA/Leon Mk3 (5F) Shop By Car/SEAT/CUPRA/Leon Mk4 Shop By Car/Skoda/Octavia Mk4  

Read more less

Here we introduce to you our #Enhanced Edition H1 LED Upgrade. This product can NOT be used as a cornering light! Vision, Without Restriction The output on these bulbs is truly phenomenal, whilst the latest technology and components allows for superior beam without damaging OEM Components. Designed to fit as any OEM part would, but offering a a higher lumen output. Unlike other suppliers, CEUK has developed an LED bulb which does not require the splicing of wires and difficult intricate clips to hold the lamp in place. This unit fits in its entirety as an OEM H1 Halogen bulb would. The LED's come as standard 6000K ice white,  Its worth noting that due to the design of headlamps, different lamps and light units may give different results to those found in our pictures. Good to know. High Lumen Output Improved visibility in the evenings Reduced strain on the eyes suitable for use in all builds of headlamps Suitable for projector and reflector headlamps Technical Info Voltage: 12v Wattage: 50W Per Bulb Lumens: 20,000 (10,000 Per Bulb) What's in the box 2x H1 LED Units (6000k Default) Warranty: The product is provided with a 12 Months guarantee as standard, Unless stated on the product packaging. If the packaging states more than 12 months, the product packaging must be kept to retain the extended warranty. Vehicle Fitment: Some vehicles may use different types of bulbs depending on spec levels - For example, a special edition vehicle (Such as Ford "ST" or VW "GTi") may have a different light unit to a standard spec. If this item is listed on your vehicle catergory please confirm that it is the correct fitment for your vehicle by checking your item prior to ordering. The installation of LED's may trigger a Dashboard Error Message which is a harmless side effect of lower powered units, if this occurs for you please refer to our FAQ's. 

Read more less