All

VW GOLF MK6 GTI HIGH FLOW AIR FILTER INTAKE SYSTEM Our full air filter intake kit offers the following:  Replaces the complete standard airbox and includes heat-shield to the conical filter Includes full fitting kit and instructions for simple fitting Increases engine note – releasing the real noise of your engine Longer lifespan before cleaning required, compared to original or cotton filters Easy cleaning, no dirt caught like with V shaped filter grooves Bench tested for improved fuel economy, power and torque outputs The triple layer foam design The low maintenance and long lifespan aspects of a Revo filter come from the special triple layer foam that is used on all of our air filters. The outer core is coarse foam designed to trap larger particles, the middle core is Medium foam designed to trap most particles and the inner core is fine foam which will trap the remainder of the particles. The triple layer foam design ensures an exceptional level of engine protection in any conditions.   VEHICLE APPLICATIONS      Manufacturer Model Engine Year Audi A3 (8P) 2.0 TSI 2003 - 2012 Seat Leon MK2 2.0 TSI 2005 - 2012 Skoda Octavia Mk2 1.8 / 2.0 TSI 2005 - 2013 VW Golf MK6 2.0 TSI 2008 - 2013 VW Beetle 2.0 TSI 1999 > VW Scirocco 2.0 TSI 2008 > VW Tiguan 2.0 TSI 2007 > Notes: Simple replacement of the OEM part Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

TURBO INLET HOSE The Revo Turbo Inlet Hose has been designed and engineered to directly replace the stock pipe and elbow found in vehicles with the 1.8 and 2.0 TSI engines with an IHI turbo. The Revo Turbo Inlet Hose offers a high-quality single piece replacement for the OEM parts which allows for smoother uninterrupted airflow, improving the throttle response and performance of your vehicle. KEY FEATURES Increased performance Improves airflow efficiency Constant taper for smoother flow Turbo matched inlets Replaces restrictive stock turbo elbow Engineered for both LHD and RHD fitment OEM PART With ample efficiency for a stock vehicle, the OEM system quickly becomes a choking point for the engine when running Revo Software. With a generously sized airbox, the standard plastic intake hose causes the most amount of restriction; convolutions designed to allow for engine movement disrupt airflow, a small internal diameter limits the volume of air and a sharp reduction in hose diameter at the turbo causes turbulence.   TURBO INLET The Revo machined inlet replaces the restrictive elbow found on the IS20/IS38 turbos. The machined billet aluminium inlet securely fits the OE unit using locking tabs and integrated O-rings. With almost double the cross-sectional area compared to other available products, air can stabilise and distribute before a smooth tapered transition to the turbo. Removing the internal steps between components further ensures uninterrupted airflow and removes any unnecessary turbulence.   SILICONE HOSE DESIGN The Revo Turbo Hose as an increased inner diameter that gradually tapers from airbox to turbo to optimise airflow, while maintaining the tolerances required to fit both LHD and RHD vehicles with a standard airbox. Designed to directly replace the plastic hose and turbo elbow, this upgrade reduces restriction and maximises smooth airflow improving both power and torque throughout the rev range.   A four-ply construction with an internal wire helix increases strength to prevent collapsing under pressure. Internal steps flush fit against the stock airbox and the machined inlet, creating a smooth transition between components ensuring the smoothest airflow possible to the turbo. A machined bung is integrated into the hose, connecting the stock PCV system vacuum.       RESEARCH AND DEVELOPMENT All Revo products are designed in-house and are rigorously tested. The Revo Turbo Inlet Hose allows the Stock IS38 turbo to run more efficiently, intake a larger volume of air and minimise turbulence. This increases power and torque, especially at the top end of the rev range as highlighted during controlled Dyno testing.   GRAPHS DATA Up to 12WHP and 15NM gains Graphs produced with Revo stage 2 software on Audi S3 8V Stock Runs with complete OEM Air intake setup Revo Runs with Revo Intake Hose and ProPanel Filter   VEHICLE APPLICATIONS   Manufacturer Model Engine Year Audi A3 (8V) 1.8 / 2.0 TFSI 12 - Audi S3 (8V) 2.0 TFSI 12 - Audi TT (MK3) 2.0 TFSI 15 - Audi TTS (MK3) 2.0 TFSI 15 - Seat Leon (MK3) 1.8 / 2.0 TSI 12 - Skoda Octavia (MK3) 1.8 / 2.0 TFSI 12 - Skoda Superb 2.0 TSI 15 - Volkswagen Golf (MK7) R 2.0 TSI 12 - Volkswagen Golf (MK7) GTI 2.0 TSI 12 - Volkswagen Golf (MK7) 1.8 TSI 12 - Volkswagen Passat 2.0 TSI 15 -  

Read more less

  AUDI 2.0 TFSI INTAKE INCREASED BHP, TORQUE AND THROTTLE RESPONSE The Revo Air Intake System for the B8 2.0TFSI engine has been designed to work in harmony with Revo software giving access to more power and torque along with a sportier engine note and enhanced turbo sound. A custom silicone hose with stepped neck promotes smoother airflow into the turbo removing the turbulence caused in the stock system as well a reduced distance for the air to travel. The stock MAF unit has been utilised to give optimum scaling after testing found no improvements on relocating it. A Revo high-flow filter with three-layer foam maximises efficiency and protection to the engine. The kit comes complete with a heatshield specifically designed to utilise the stock air duct for the most direct source of cold air. KEY FEATURES +5 WHP & +9 NM Torque Custom Heatshield Revo 3 Stage Foam Filter Improved Throttle Response Flush Fit Silicone Hose Increased Airflow   VEHICLE APPLICATIONS   Manufacturer Model Engine Year Audi A4 (B8) 2.0 TFSI 2007 - 2012 Audi A5 (B8) 2.0 TFSI 2007 - 2011   Notes: Simple replacement of the OEM part Does not fit B8.5 models  Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

Revo Big Brake Kit UpgradeImproves stopping power under any condition OVERVIEW The Revo Big Brake Kit Upgrade is engineered to improve your stopping power in any condition. Whilst stock brakes are perfectly adequate for general driving; the braking system is often overlooked when enhancing a vehicle's performance. The Revo brake kit is made by world-leading brake manufacturer Alcon; utilising over 30years of motorsport braking innovation only the best materials, techniques and processes have been used. In-depth testing is a key factor in the development of our products; our brake kits have been aggressively tested in a variety of conditions in both road and track scenarios to ensure they meet the constant high stress of track days, sprints and fast road driving. Test kits were installed on our in house development vehicles along with several vehicles around the world and put through their paces to prove their worth over the stock setup; providing exceptional performance combined with consistency and durability you can rely on, corner after corner, stop after stop. Made by world leading brake manufacturer Alcon, only the best materials, techniques and processes have been used, with every step of the manufacturing process completed in the UK. Alcon has been at the forefront of motorsport braking innovation for over 30 years. BENEFITS Low Rotational Mass Improved Pedal Responsiveness Lower Long-term Maintenance Costs Superior Heat Dissipation: Less Prone To Fade Increased Braking Performance On & Off Track 100 - 0 MPH AVERAGE STOPPING DISTANCE CALIPERS Our lightweight six-pot caliper is a single-piece aluminium Mono-bloc design. This design has been used to maximise rigidity, pedal feel and overall braking performance. The caliper incorporates a progressive six-piston setup to give great brake balance, and high quality seals increasing resilience to road salts and other corrosive elements. DISCS We use a two-piece floating disc and hat design to efficiently dissipate heat. The friction surface features crescent groves designed to increase bite and remove debris from the pad surface giving the perfect balance between brake feel and longevity. The discs feature internal cooling vanes that draw air from the centre of the disc outward to maximise heat dissipation and minimise heat transfer to the calipers, pads, and brake fluid, which plays an all-important part in providing consistent stopping power for your vehicle. BRAKE PADS We supply our brake kit with Ferodo DS Performance Pads that offer a consistent pedal feel and fantastic braking performance both from cold and when hot. Combined with low wheel dusting, minimal noise characteristics, and low disc and pad wear rates this is the ideal pad compound for general road and track driving. BRAKE LINES Our brake kit is supplied with stainless lines; consisting of a PTFE inner and stainless steel braided outer to eliminate the spongy feel of original rubber hoses, provide superior resistance to corrosion, and offer consistent braking performance. BRAKE FLUID Our brakes are supplied with Motul Dot 5.1 brake fluid; specifically designed for brakes systems with ABS. This is a long-life synthetic brake fluid with superior boiling point qualities to conventional Dot 3 and 4 spec. fluids. KIT CONTENTS Revo by Alcon Caliper x2 (3.3 Kg Each) Revo by Alcon Discs x2 (7.66 Kg Each) 6061 Aluminium Anodised Bell x2 6061 Aluminium Anodised Caliper Bracket Revo Stainless Steel Braided Brake Lines Motul Dot 5.1 Brake Fluid Ferodo DS Performance Brake Pads   TECHNICAL DOCUMENTS The following documents are available to view: FITTING TEMPLATE Download the Revo Big Brake Printable 355mm Disc Template. See if the Big Brake kits will fit inside your wheels. FITTING TEMPLATE Download the Revo Big Brake Printable 380mm Disc Template. See if the Big Brake kits will fit inside your wheels.   FITMENT       Manufacturer Model Engine Year Audi A4 (B8) Various  2007 - 2015  Audi S4 (B8) 3.0 TFSI  2009 - 2015 Audi S5 (B8) Various  2007 - 2015 Audi Q5 Various  2008 - 2016 Audi SQ5 3.0 TFSI  2013 - 2016 Audi SQ5 3.0 TDI  2013 - 2016 Audi A5 (B8) Various  2007 - 2015   Notes: Recommended Revo Authorised Dealer Fitment only Please follow the bedding in procedure  Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

EVERYTHING YOU NEEDFOR THE POWER YOU CRAVE Enhanced power delivery, unique safety features and exhilarating response at your disposal, the Revo Performance Pack delivers much more than peak power figures. Whatever drives you, the Revo Performance Pack has it all. Engineered to perform, only Revo offers a complete tuning solution specifically designed for your vehicle. AIR INTAKE SYSTEM PERFORMANCEECU  SOFTWARE INTERCOOLER PIPE UPGRADE KIT INTERCOOLER DOWNPIPE     OEM+AIR INTAKE SYSTEM Get impressive performance benefits without compromising on the factory look of your engine bay. Revo OEM+ Air Intake Systems utilise the existing air box, replacing the restrictive ir filter and intake hose with parts precisely engineered to reduce turbulence and improve airflow. IncreasedDiameter DirectInternals ThermalBarrier Learn more about this product PERFORMANCE ECU SOFTWARE Revo performance Software is designed to safely enhance the driveability of your vehicle, giving access to more power and torque throughout the rev range while maintaining the extensive factory safety mechanisms. Revo Software offers a perfect balance of performance, economy, longevity and safety so you can drive harder, for longer. OBDII PortInstalled Vehicle HealthCheck Authorised DealerSet-up Learn more about this product     INTERCOOLER PIPE UPGRADE KIT The Revo Intercooler Pipe Upgrade kit offers incredible power and torque increases by reducing charge system resistance and improving flow compared to the restrictive stock pipework. Featuring larger internal diameters, fewer restrictions for smoother airflow, and optimised routing, the turbo meets less resistance and can perform more effectively. IncreasedDiameter DirectInternals Learn more about this product DOWNPIPE UPGRADE The Revo downpipe upgrade is designed to replace the restrictive OEM component with a hi-flow 200 CELL Sports CAT, allowing exhaust gasses to flow much more freely. Designed alongside Revo Performance Software, it forms an important part of the Revo Performance Pack, unleashing more potential power from the engine. DirectReplacement IncreasedDiameter Learn more about this product     TURBO MUFFLER DELETE The Revo Turbo Muffler Delete offers a high-quality single piece replacement for the OEM part which allows for smoother uninterrupted air flow, increasing throttle response and providing improved turbo acoustics. DirectReplacement DirectInternals Learn more about this product INTERCOOLER UPGRADE The Revo Intercooler was built around a simple principle; create a cooler that can keep up with your demand for power. Unique design features lower intake air temperatures, minimise pressure drop and allow the engine to produce impressive power and torque with Revo Software, ensuring you get consistent performance when you need it most. DirectReplacement UniqueFin Design MinimisedPressure Drop Learn more about this product     STOCK POWER252 PS TORQUE370 NM 0 - 60 MPH5.8 S 0 - 10014.5 S POWER336 PS TORQUE468 NM 0 - 60 MPH4.3 S 0 - 10010.3 S Find your nearest Revo Authorised Dealer Manufacturer Model Variant Engine Year Audi A5 B9 2.0 TFSI 2017 >

Read more less

REVO OEM+ INTAKE SYSTEM Get impressive performance benefits without compromising on the factory look of your engine bay. Revo OEM+ Air Intake Systems utilise the existing airbox, replacing any restrictive components with parts precisely engineered to reduce turbulence and improve airflow. The B9 Audi A4/S5 shares the same airbox as the higher-powered S4/5 and RS4/5 models and performed well during initial testing of volume and flow, however, there was room for improvement. This air intake system upgrade includes a Revo foam filter and a flush-fit silicone hose to minimise air restriction and turbulence, improving airflow and giving you access to more power. KEY FEATURES Increased Airflow by up to 15% Three-layer foam filter Stepped Silicone Hose KIT CONTENTS Revo ProPanel Filter Revo Silicone Hose Revo Takeoff Stainless Steel Clamps AIR FILTER The standard paper filter found in most vehicles performs well under normal conditions, however, with increased power it becomes a major choking point in the system. Revo filters work by trapping dirt particles within each of the oiled foam layers while allowing air to negotiate its way through, reducing restriction and offering much longer service intervals. The new Revo filter features an OEM top plate, allowing a direct fit replacement for the stock airbox. SILICONE HOSE The plastic hose on the stock system is designed with a corrugated style to flex with the engine movement, while this has its place it also causes a large amount of turbulence as the airflow doesn’t have a smooth direct path to the turbo. We designed the silicone hose with stepped internals to ensure a flush fit, and to minimise turbulence while still allowing for engine movement. SELF-SEAL TAKEOFF The OE B9 A4/A5 intake hose has a small vacuum take-off used to supply vacuum to various components of the engine. To replicate this, the Revo B9 A4/A5 intake hose utilizes a threaded self-seal barb. This machined configuration offers a better aesthetic and more durability than typical plastic and glued couplers.   AIRFLOW Testing of the stock unit back to back against the Revo OEM+ kit on a full flow bench was carried out to highlight the largest restrictions in the system. The Revo OEM+ Intake system had far less restriction than the OE unit, at 600CFM the stock unit was seeing 986mmwg restriction while the Revo unit only saw 843mmwg some 14.6% less restriction. At low flow rate, the Revo intake provided up to 15% less restriction, improving throttle response. The graph below shows the flow test and comparison between the OE and Revo intakes.   FITMENT   Manufacturer Model Engine Variant Year Audi A4 2.0TFSI B9 190PS 2015> Audi A5 2.0TFSI B9 190PS 2015>   Notes: Simple replacement of the OEM part Plastic airbox lid not included in the kit Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

The Revo Big Brake Kit comes complete with everything required to upgrade your stopping power. With Calipers and discs manufactured by industry leaders Alcon® and a floating system designed by our in-house engineers, each kit includes everything you need in one box; brake lines, brake pads, floating discs, mono-bloc calipers, brackets and even brake fluid.   Revo Big Brake Kit UpgradeImproves stopping power under any condition OVERVIEW The Revo Big Brake Kit Upgrade is engineered to improve your stopping power in any condition. Whilst stock brakes are perfectly adequate for general driving; the braking system is often overlooked when enhancing a vehicle's performance. The Revo brake kit is made by world-leading brake manufacturer Alcon; utilising over 30years of motorsport braking innovation only the best materials, techniques and processes have been used. In-depth testing is a key factor in the development of our products; our brake kits have been aggressively tested in a variety of conditions in both road and track scenarios to ensure they meet the constant high stress of track days, sprints and fast road driving. Test kits were installed on our in house development vehicles along with several vehicles around the world and put through their paces to prove their worth over the stock setup; providing exceptional performance combined with consistency and durability you can rely on, corner after corner, stop after stop. Made by world leading brake manufacturer Alcon, only the best materials, techniques and processes have been used, with every step of the manufacturing process completed in the UK. Alcon has been at the forefront of motorsport braking innovation for over 30 years. BENEFITS Low Rotational Mass Improved Pedal Responsiveness Lower Long-term Maintenance Costs Superior Heat Dissipation: Less Prone To Fade Increased Braking Performance On & Off Track 100 - 0 MPH AVERAGE STOPPING DISTANCE CALIPERS Our lightweight six-pot caliper is a single-piece aluminium Mono-bloc design. This design has been used to maximise rigidity, pedal feel and overall braking performance. The caliper incorporates a progressive six-piston setup to give great brake balance, and high quality seals increasing resilience to road salts and other corrosive elements. DISCS We use a two-piece floating disc and hat design to efficiently dissipate heat. The friction surface features crescent groves designed to increase bite and remove debris from the pad surface giving the perfect balance between brake feel and longevity. The discs feature internal cooling vanes that draw air from the centre of the disc outward to maximise heat dissipation and minimise heat transfer to the calipers, pads, and brake fluid, which plays an all-important part in providing consistent stopping power for your vehicle. BRAKE PADS We supply our brake kit with Ferodo DS Performance Pads that offer a consistent pedal feel and fantastic braking performance both from cold and when hot. Combined with low wheel dusting, minimal noise characteristics, and low disc and pad wear rates this is the ideal pad compound for general road and track driving. BRAKE LINES Our brake kit is supplied with stainless lines; consisting of a PTFE inner and stainless steel braided outer to eliminate the spongy feel of original rubber hoses, provide superior resistance to corrosion, and offer consistent braking performance. BRAKE FLUID Our brakes are supplied with Motul Dot 5.1 brake fluid; specifically designed for brakes systems with ABS. This is a long-life synthetic brake fluid with superior boiling point qualities to conventional Dot 3 and 4 spec. fluids. KIT CONTENTS Revo by Alcon Caliper x2 (3.3 Kg Each) Revo by Alcon Discs x2 (7.66 Kg Each) 6061 Aluminium Anodised Bell x2 6061 Aluminium Anodised Caliper Bracket Revo Stainless Steel Braided Brake Lines Motul Dot 5.1 Brake Fluid Ferodo DS Performance Brake Pads   TECHNICAL DOCUMENTS The following documents are available to view: FITTING TEMPLATE Download the Revo Big Brake Printable 355mm Disc Template. See if the Big Brake kits will fit inside your wheels. FITTING TEMPLATE Download the Revo Big Brake Printable 380mm Disc Template. See if the Big Brake kits will fit inside your wheels.   FITMENT       Manufacturer Model Engine Year Audi A4 (B9) Various  2016 - Present  Audi S4 (B9) 3.0 TFSI  2016 - Present Audi A5 (B9) Various  2017 - Present Audi S5 (B9) 3.0 TFSI  2017 - Present Audi Q5 (FY) Various  2017 - Present Audi SQ5 (FY) 3.0 TFSI  2017 - Present   Notes: Recommended Revo Authorised Dealer Fitment only Please follow the bedding in procedure  Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

Revo Big Brake Kit UpgradeImproves stopping power under any condition OVERVIEW The Revo Big Brake Kit Upgrade is engineered to improve your stopping power in any condition. Whilst stock brakes are perfectly adequate for general driving; the braking system is often overlooked when enhancing a vehicle's performance. The Revo brake kit is made by world-leading brake manufacturer Alcon; utilising over 30years of motorsport braking innovation only the best materials, techniques and processes have been used. In-depth testing is a key factor in the development of our products; our brake kits have been aggressively tested in a variety of conditions in both road and track scenarios to ensure they meet the constant high stress of track days, sprints and fast road driving. Test kits were installed on our in house development vehicles along with several vehicles around the world and put through their paces to prove their worth over the stock setup; providing exceptional performance combined with consistency and durability you can rely on, corner after corner, stop after stop. Made by world leading brake manufacturer Alcon, only the best materials, techniques and processes have been used, with every step of the manufacturing process completed in the UK. Alcon has been at the forefront of motorsport braking innovation for over 30 years. BENEFITS Low Rotational Mass Improved Pedal Responsiveness Lower Long-term Maintenance Costs Superior Heat Dissipation: Less Prone To Fade Increased Braking Performance On & Off Track 100 - 0 MPH AVERAGE STOPPING DISTANCE CALIPERS Our lightweight six-pot caliper is a single-piece aluminium Mono-bloc design. This design has been used to maximise rigidity, pedal feel and overall braking performance. The caliper incorporates a progressive six-piston setup to give great brake balance, and high quality seals increasing resilience to road salts and other corrosive elements. DISCS We use a two-piece floating disc and hat design to efficiently dissipate heat. The friction surface features crescent groves designed to increase bite and remove debris from the pad surface giving the perfect balance between brake feel and longevity. The discs feature internal cooling vanes that draw air from the centre of the disc outward to maximise heat dissipation and minimise heat transfer to the calipers, pads, and brake fluid, which plays an all-important part in providing consistent stopping power for your vehicle. BRAKE PADS We supply our brake kit with Ferodo DS Performance Pads that offer a consistent pedal feel and fantastic braking performance both from cold and when hot. Combined with low wheel dusting, minimal noise characteristics, and low disc and pad wear rates this is the ideal pad compound for general road and track driving. BRAKE LINES Our brake kit is supplied with stainless lines; consisting of a PTFE inner and stainless steel braided outer to eliminate the spongy feel of original rubber hoses, provide superior resistance to corrosion, and offer consistent braking performance. BRAKE FLUID Our brakes are supplied with Motul Dot 5.1 brake fluid; specifically designed for brakes systems with ABS. This is a long-life synthetic brake fluid with superior boiling point qualities to conventional Dot 3 and 4 spec. fluids. KIT CONTENTS Revo by Alcon Caliper x2 (3.3 Kg Each) Revo by Alcon Discs x2 (7.66 Kg Each) 6061 Aluminium Anodised Bell x2 6061 Aluminium Anodised Caliper Bracket Revo Stainless Steel Braided Brake Lines Motul Dot 5.1 Brake Fluid Ferodo DS Performance Brake Pads   TECHNICAL DOCUMENTS The following documents are available to view: FITTING TEMPLATE Download the Revo Big Brake Printable 355mm Disc Template. See if the Big Brake kits will fit inside your wheels. FITTING TEMPLATE Download the Revo Big Brake Printable 380mm Disc Template. See if the Big Brake kits will fit inside your wheels.   FITMENT       Manufacturer Model Engine Year Audi A4 (B8) Various  2007 - 2015  Audi S4 (B8) 3.0 TFSI  2009 - 2015 Audi S5 (B8) Various  2007 - 2015 Audi Q5 Various  2008 - 2016 Audi SQ5 3.0 TFSI  2013 - 2016 Audi SQ5 3.0 TDI  2013 - 2016 Audi A5 (B8) Various  2007 - 2015   Notes: Recommended Revo Authorised Dealer Fitment only Please follow the bedding in procedure  Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

Revo Big Brake Kit UpgradeImproves stopping power under any condition OVERVIEW The Revo Big Brake Kit Upgrade is engineered to improve your stopping power in any condition. Whilst stock brakes are perfectly adequate for general driving; the braking system is often overlooked when enhancing a vehicle's performance. The Revo brake kit is made by world-leading brake manufacturer Alcon; utilising over 30years of motorsport braking innovation only the best materials, techniques and processes have been used. In-depth testing is a key factor in the development of our products; our brake kits have been aggressively tested in a variety of conditions in both road and track scenarios to ensure they meet the constant high stress of track days, sprints and fast road driving. Test kits were installed on our in house development vehicles along with several vehicles around the world and put through their paces to prove their worth over the stock setup; providing exceptional performance combined with consistency and durability you can rely on, corner after corner, stop after stop. Made by world leading brake manufacturer Alcon, only the best materials, techniques and processes have been used, with every step of the manufacturing process completed in the UK. Alcon has been at the forefront of motorsport braking innovation for over 30 years. BENEFITS Low Rotational Mass Improved Pedal Responsiveness Lower Long-term Maintenance Costs Superior Heat Dissipation: Less Prone To Fade Increased Braking Performance On & Off Track 100 - 0 MPH AVERAGE STOPPING DISTANCE CALLIPERS Our lightweight six-pot calliper is a single-piece aluminium Mono-bloc design. This design has been used to maximise rigidity, pedal feel and overall braking performance. The calliper incorporates a progressive six-piston setup to give great brake balance, and high quality seals increasing resilience to road salts and other corrosive elements. DISCS We use a two-piece floating disc and hat design to efficiently dissipate heat. The friction surface features crescent groves designed to increase bite and remove debris from the pad surface giving the perfect balance between brake feel and longevity. The discs feature internal cooling vanes that draw air from the centre of the disc outward to maximise heat dissipation and minimise heat transfer to the callipers, pads, and brake fluid, which plays an all-important part in providing consistent stopping power for your vehicle. BRAKE PADS We supply our brake kit with Ferodo DS Performance Pads that offer a consistent pedal feel and fantastic braking performance both from cold and when hot. Combined with low wheel dusting, minimal noise characteristics, and low disc and pad wear rates this is the ideal pad compound for general road and track driving. BRAKE LINES Our brake kit is supplied with stainless lines; consisting of a PTFE inner and stainless steel braided outer to eliminate the spongy feel of original rubber hoses, provide superior resistance to corrosion, and offer consistent braking performance. BRAKE FLUID Our brakes are supplied with Motul Dot 5.1 brake fluid; specifically designed for brakes systems with ABS. This is a long-life synthetic brake fluid with superior boiling point qualities to conventional Dot 3 and 4 spec. fluids. KIT CONTENTS Revo by Alcon Caliper x2 (3.3 Kg Each) Revo by Alcon Discs x2 (7.66 Kg Each) 6061 Aluminium Anodised Bell x2 6061 Aluminium Anodised Caliper Bracket Revo Stainless Steel Braided Brake Lines Motul Dot 5.1 Brake Fluid Ferodo DS Performance Brake Pads     TECHNICAL DOCUMENTS The following documents are available to view:   FITTING TEMPLATE Download the Revo Big Brake Printable 355mm Disc Template. See if the Big Brake kits will fit inside your wheels. FITTING TEMPLATE Download the Revo Big Brake Printable 380mm Disc Template. See if the Big Brake kits will fit inside your wheels.   FITMENT      Manufacturer Model Engine Year Audi RS3 (8P) 2.5 TFSI  2010 - 2012   Notes: Recommended Revo Authorised Dealer fitment only. Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

CARBON SERIES AIR INTAKE SYSTEM AUDI RS3 8V 2.5 TFSI The intake system on your Audi RS3 has been designed to function effectively for a standard engine and to minimise intake noise for comfort. Particularly with Revo Software installed, this restrictive plastic intake system literally chokes the engine as it struggles to flow enough air through the system. Only the driven understand that by replacing the OEM intake, you can see excellent performance benefits that Only Revo offer. And as this product is part of the Carbon Series, it also completely transforms the appearance of your engine bay; this intake is literally as powerful as it looks. CARBON SERIES QUALITY HI-FLOW PANEL FILTER DIRECT REPLACEMENT KIT INCREASED THROTTLE RESPONSE PROVEN PERFORMANCE BENEFITS   Performance is the core reason that Revo produces any product, and is certainly the case with this upgrade. An addition that any RS3 owner can be proud of, the most impressive benefit is the extra power and torque that is unleashed when used with Revo Stage 1 software. SILICONE HOSE Hand-built using automotive-grade silicone in a four-ply construction for strength. Each silicone joiner features a flush-fit neck to ensure a smooth flow of air and to avoid turbulence. CAD designed with maximum radius bends for better flow. A CNC machined billet aluminium piece joins the pipe to the airbox along with a vacuum fitting to rid the system of the standard plastic components.  Read more   PRO PANEL FILTER Revo ProPanel Filters use multi-layered foam technology to trap dust and dirt while maintaining flow efficiency over time and are washable. Paper and cotton filters, which trap dust on the surface are less efficient the more they are used, choking the engine and reducing performance. HIGH QUALITY The 3K carbon weave used on all Revo Carbon Series products whilst looking great also gives exceptional strength when combined with the manufacturing process, ensuring a high-quality long life part for your vehicle.   DYNO TESTING Dyno testing with Stage 1 software proved a 21WHP gain @4300rpm and over 11WHP at peak RPM with a consistent and strong gain through the rev range. Torque is also dramatically increased with 28NM gain over stock at peak. Increased airflow also means that the turbo can spool up quicker, delivering power and torque earlier in the rev-range. This is further backed up airflow testing which shows an increase of 23kg/h over the stock pipe as the car starts to spool up, this improved flow continues through to peak where it still made an extra 12kg/h over the stock part.     FITMENT   Manufacturer Model Engine Year Audi RS3 8V 2.5 TFSI 2015 >   Revo Carbon Series air intake systems perform beautifully. Designed to function no matter the power, Carbon Series intakes look great because of their effective design. Click to find out more   Notes: Simple replacement of the OEM part Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

Revo Big Brake Kit UpgradeImproves stopping power under any condition OVERVIEW The Revo Big Brake Kit Upgrade is engineered to improve your stopping power in any condition. Whilst stock brakes are perfectly adequate for general driving; the braking system is often overlooked when enhancing a vehicle's performance. The Revo brake kit is made by world-leading brake manufacturer Alcon; utilising over 30years of motorsport braking innovation only the best materials, techniques and processes have been used. In-depth testing is a key factor in the development of our products; our brake kits have been aggressively tested in a variety of conditions in both road and track scenarios to ensure they meet the constant high stress of track days, sprints and fast road driving. Test kits were installed on our in-house development vehicles along with several vehicles around the world and put through their paces to prove their worth over the stock setup; providing exceptional performance combined with consistency and durability you can rely on, corner after corner, stop after stop. Made by world leading brake manufacturer Alcon, only the best materials, techniques and processes have been used, with every step of the manufacturing process completed in the UK. Alcon has been at the forefront of motorsport braking innovation for over 30 years. BENEFITS Low Rotational Mass Improved Pedal Responsiveness Lower Long-term Maintenance Costs Superior Heat Dissipation: Less Prone To Fade Increased Braking Performance On & Off Track 100 - 0 MPH AVERAGE STOPPING DISTANCE CALLIPERS Our lightweight six-pot calliper is a single-piece aluminium Mono-bloc design. This design has been used to maximise rigidity, pedal feel and overall braking performance. The calliper incorporates a progressive six-piston setup to give great brake balance, and high quality seals increasing resilience to road salts and other corrosive elements. DISCS We use a two-piece floating disc and hat design to efficiently dissipate heat. The friction surface features crescent groves designed to increase bite and remove debris from the pad surface giving the perfect balance between brake feel and longevity. The discs feature internal cooling vanes that draw air from the centre of the disc outward to maximise heat dissipation and minimise heat transfer to the callipers, pads, and brake fluid, which plays an all-important part in providing consistent stopping power for your vehicle. BRAKE PADS We supply our brake kit with Ferodo DS Performance Pads that offer a consistent pedal feel and fantastic braking performance both from cold and when hot. Combined with low wheel dusting, minimal noise characteristics, and low disc and pad wear rates this is the ideal pad compound for general road and track driving. BRAKE LINES Our brake kit is supplied with stainless lines; consisting of a PTFE inner and stainless steel braided outer to eliminate the spongy feel of original rubber hoses, provide superior resistance to corrosion, and offer consistent braking performance. BRAKE FLUID Our brakes are supplied with Motul Dot 5.1 brake fluid; specifically designed for brakes systems with ABS. This is a long-life synthetic brake fluid with superior boiling point qualities to conventional Dot 3 and 4 spec. fluids. KIT CONTENTS Revo by Alcon Caliper x2 (3.3 Kg Each) Revo by Alcon Discs x2 (7.66 Kg Each) 6061 Aluminium Anodised Bell x2 6061 Aluminium Anodised Caliper Bracket Revo Stainless Steel Braided Brake Lines Motul Dot 5.1 Brake Fluid Ferodo DS Performance Brake Pads     TECHNICAL DOCUMENTS The following documents are available to view:  FITTING TEMPLATE Download the Revo Big Brake Printable 355mm Disc Template. See if the Big Brake kits will fit inside your wheels. FITTING TEMPLATE Download the Revo Big Brake Printable 380mm Disc Template. See if the Big Brake kits will fit inside your wheels.   FITMENT      Manufacturer Model Engine Year Audi RS3(8V) 2.5 TFSI 2015 - 2017 Audi RS3(8V2) Sportsback 2.5 TFSI 2018 >   Notes: Recommended Revo Authorised Dealer Fitment only.  Does not fit the RS3 Facelift Sedan Please contact your local Revo Authorised Dealer for additional information and availability. © Revo

Read more less

AUDI RS3 BRAKE DISC UPGRADE The Audi RS3 comes with a fairly substantial 8-pot brake setup straight from the factory. Whilst the stock calliper works very well the same can’t be said for the discs or the factory specification pads that seem to perform best at lower temperatures or very light road use. The factory 370mm 'wavy' discs certainly look the part but the design flaw is that both discs are identical; when fitted, the cooling vanes in the right-hand disc face the wrong direction and do not offer any cooling benefit. The excessive heat this generates combined with the factory pad compound causes big issues with braking efficiency and longevity of the disc and pads. The Revo disc upgrade is designed to directly replace the stock discs and comes complete and ready to fit with left and right-handed, directional 380mm two-piece floating discs. Saving 1.2 Kg each side the disc not only weighs less than the OEM part but also features much larger, more efficient cooling veins individually designed for each side of the vehicle to ensure even braking performance, pad wear and cooling capability. This is a premium upgrade that should have come from the factory. As the Revo discs dissipate heat much more efficiently the factory pad compound works much better in real-world conditions, only when you’re using the vehicle on the track would we recommend considering a different pad altogether. KEY FEATURES Left & right handed discs + 5% braking surface Two-piece floating design + 10mm larger disc Larger more efficient cooling vanes   HEAT MANAGEMENT Heat is an unavoidable by-product of friction. Managing this heat efficiently is extremely important to avoid it transferring to the pads, calliper and fluid. The OEM RS3 discs are manufactured as a single part, pumping air in different directions on each side of the vehicle. This causes varying levels of cooling efficiency and temperatures leading to judder and brake fade. REVO DISCS Revo discs are manufactured by Alcon and utilise over thirty years of motorsport expertise in their design and manufacture. Internal vanes are used to draw air through the centre of the disc outward, allowing the heat to transfer as it passes. The rotation of the discs and vanes play an important role in brake cooling as it acts as a pump to move air and unlike the OEM brake discs, the Revo upgrade consists of a right and left-hand disc to optimise cooling and ensure consistent stopping power for your vehicle.   TWO-PIECE FLOATING DESIGN Utilising a two-piece floating design allows the disc and hat to expand radially and axially as they absorb heat generated from use, avoiding the most common cause of warping and cracking seen in single-piece rotors. Due to the efficiency of this design, Revo discs last considerably longer than factory discs. The friction surface features crescent groves that increase bite and remove debris from the pad surface giving the perfect balance between brake feel and longevity while minimizing the pedal pulsations normally associated with straight-slotted rotors or cracking issues common with cross-drilled rotors.   VEHICLE APPLICATION   Manufacturer Model Engine Year Audi RS3 8V 2.5 TFSI 2015 onwards   Notes: Recommended Revo Authorised Dealer Fitment only.  Does not fit Sedan/Saloon models.  Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

REVO INTERCOOLER AUDI RS3 8V2 The Revo Intercooler utilises unique design features to lower intake air temperatures, minimise pressure drop and allow the engine to produce impressive power and torque with Revo Software. The unique end tank profile promotes internal laminar flow by decreasing turbulence and increasing airspeed into the bar and plate core. This enhances charge air cooling giving you access to more power throughout the rev range. The limitations of the stock intercooler were apparent throughout testing. The stock part consistently struggled to manage charge air temperatures, especially on vehicles with performance software. The Revo Intercooler has been designed to improve on every restrictive element of the stock cooler, enhancing cooling efficiency by lowering intake air temperatures by up to 38ºC vs. the Stock intercooler, allowing you to drive harder, for longer. KEY FEATURES Bar & Plate Core Design Fully Cast End Tanks Reinforced Mounting Brackets Intercooler Pipes Included Up to 53% increase in the frontal surface area Up to 38% increase in core volume Fits with OEM Crash Bar   INCREASED CORE VOLUME The Revo Intercooler was built around a simple principle; create a cooler that can keep up with your power demand. Designed from the ground up, the Revo Intercooler has a 38% larger core volume than the OEM part and offers perfect fitment by Utilising the volume of unused engine bay space behind the OEM (US and ROW) crash bar. INCREASED FRONTAL AREA Due to the custom-designed end tanks, the frontal area of the intercooler has been increased by a massive 53%. Offering the best balance between increased performance and acceptable part clearance, whilst also minimising pressure drop.   END TANK DESIGN The Revo end tank geometry maintains the largest possible cross-sectional flow area to and from the core. With a cast interior surface finish, the Revo end tanks allow air to flow freely without obstructions. The design has been balanced between core width and optimal tank profile design. End tanks play an important part in maintaining pressure and work in harmony with the core to promote airflow, the Revo end tanks are designed to offer the optimal balance between both of these key features.   BAR & PLATE Designed with a bar and plate core to maximise the efficiency of heat transfer, the pressure drop is also controlled as the air meets less resistance compared to that of a tube and fin alternative. The Revo Intercooler also features carefully specified fin geometry to maximise cooling properties while minimising flow restriction. The ambient core side utilises louvred fins to slow ambient airflow which improves heat transfer, while the charge core side features an offset internal fin design to balance surface area and air resistance to minimise pressure drop.   INTERCOOLER PIPE UPGRADE Supplied with an upgraded aluminium charge and silicone throttle pipes. The increased diameter pipework ensures the maximum performance by increasing system volume by over 27%. The internal diameter of each silicone is precisely matched to the outer diameter of the ribbed inlet and outlet connections along with a unique Flush Fit design, allowing a smooth transition between components. RESEARCH AND DEVELOPMENT All Revo products are designed in-house using the latest 3D printing technology, CAD and CFD software. Every product is rigorously tested utilising an in-house Hub dyno and Revo data acquisition software. The Revo intercooler minimises turbulence while maximising heat transfer, promoting cooler air temperatures and low-pressure drop. This helps retains power and torque throughout the rev range as highlighted during controlled Dyno testing. The Revo Intercooler was tested in-house to compare the performance against that of the stock Intercooler. First tested on a vehicle running the OEM Intercooler with Revo software, a Revo carbon series air intake system and Milltek downpipe exhaust, the Revo Intercooler and pipes were then installed and tested in the same controlled environment to highlight the benefits of enhanced cooling. PERFORMANCE DATA Showing the last of four consecutive dyno runs, the efficiency of the Revo Intercooler over the OEM RS3 intercooler is highlighted. With peak gains of +17 HP (hubs) & +43NM Torque, along with increased performance throughout the entire rev range. The stock intercooler struggles to effectively function in comparison to the Revo Intercooler which remained consistent throughout. INLET TEMPERATURE This is a metric used to confirm that testing on the RS3 8v.2 2.5TFSI Intercooler. This is used to show that the air temperatures going into the intercooler were similar for each test, confirming that outlet temperatures shown in the following graphs are purely down to differences in intercooler design/construction. As can be seen, the “dwell” between testing runs is higher with the OE setup vs. Revo. While this initially seems less than desirable for comparable data, this temperature difference is actually down to the thermal mass differences between setups; indicating that the Revo kit can absorb much larger amounts of heat more efficiently than the OE setup, yet the Revo intercooler produced the lower outlet temps proving the cooling efficiency. OUTLET TEMPERATURE This is the main performance metric to illustrate that the Revo intercooler far exceeds the stock unit. A strong indication that the Revo intercooler is extremely resistant to heat soak and could likely continue for ten more sequential dyno runs before any intake temperature-related issues arose. The graph illustrates the increased cooling performance of the Revo intercooler vs RS3 intercooler over all four runs. The Revo Intercooler provided a massive 38.2°C max and 18.23°C average intake air temperature reduction across the six back to back full gear dyno runs. INTERCOOLER PRESSURE DROP GRAPH Pressure drop is an important factor when it comes to choosing an Intercooler. The Revo solution features custom cast end tanks to evenly distribute air over the core. This graph highlights that even with massive core size difference there is only a 0.34psi pressure drop in comparison to the stock intercooler, ensuring engine response and minimised turbo lag     FITMENT VEHICLE APPLICATIONS Manufacturer Model Engine Year Audi RS3 2.5TFSI 2017 onwards Audi RS3 2.5TFSI GPF 2019 onwards   Notes: Simple replacement of the OEM part. Compatible with OEM Rest of World and US crash bars.  Please contact your local Revo Authorised Dealer for additional information and availability. © Revo

Read more less

REVO CONE CONE AIR INTAKE SYSTEM AUDI S1 2.0 TFSI The Revo open cone Air Intake System for the Audi S1 improves performance and offers an aggressive intake sound. Ensuring your engine can get access to enough air is paramount when increasing power; more air means more power throughout the rev-range. Only Revo Air Intake Systems are specifically designed to work in harmony with your vehicle and Revo Software. Engineered to directly replace the stock airbox, pipework and filter on the Audi S1. The Revo System offers a high-quality open cone replacement complete with a heat shield to improve airflow and the performance of your vehicle. KEY FEATURES Increased performance +13HP at hubs & +18NM Torque Improves Air Flow Efficiency 53% Larger Hose & Inlet Volume Three Stage Foam Filter with Mesh Silicone Coolant Hose OEM VS REVO When you begin to enhance performance, the restrictive OEM intake struggles to flow enough air, robbing the engine of power. The Revo Air Intake System removes these restrictive elements promoting smoother airflow. Open Cone systems replace the OEM air box to make space for the heat shield, filter and silicone hose which joins directly to the turbo inlet. Revo Flush Fit joins eliminate unwanted turbulence and increase the rate at which air can flow, ensuring maximum performance at all tuning stages. SILICONE HOSE The Revo silicone hose is designed to directly replace the plastic hose and rubber corrugated parts. Increased inlet diameter of 21% reduces restriction and promotes smooth airflow while an integrated wire helix reinforces the hose and prevents collapsing under negative pressure.   MACHINED INLET The machined inlet replaces the restrictive OEM plastic elbow and is designed to securely fit the OE unit using locking tabs and integrated O-rings. Only the Revo intake kit features an inlet almost double the cross-sectional area. This means air can stabilise and distribute before a smooth tapered transition to the turbo.   FILTER AND HEATSHIELD Ensuring the engine has access to cold air is vital for performance. The Revo heat shield channels cold air from the front intake duct while partitioning the filter from the heat of the engine bay. The Revo Heatshield uses the stock mounting points and rubber mounting bushings to provide an easy and secure installation.   RESEARCH AND DEVELOPMENT All Revo products are designed in-house and are rigorously tested utilising an in-house 3D printer, latest CAD and CFD programs, hub dyno and Revo data acquisition software. The Revo intake allows the turbo to run more efficiently, intake a larger volume of air and minimise turbulence to increase both power and torque, as highlighted during controlled Dyno testing. AIRFLOW  An overall air volume increase of 50% over the OE part allows for faster and increased airflow. The carefully designed silicone hose has its own support bracket mated to a machined hose fitting, maintaining the correct position during engine movement. A constant taper in the hose ensures a smooth transition of airflow from the air filter to turbo and results in an increase in air volume over the stock part. Further helped by the machined inlet that matches the turbo inlet for the ultimate in airflow characteristics.   DYNO GRAPH Testing was carried out on an Audi S1 2.0 TFSI (6 Speed manual) with Revo Stage 1 Software fitted with the OEM system and then the Revo Air Intake System. With a consistent gain throughout the rev range, the Revo intake offered a peak gain of 12HP at the hubs over the stock part. A maximum increase in airflow of up to +16 kg/hr gives impressive gains of 13HP @5100rpm and 18NM @5100RPM over using the stock intake system.   FITMENT VEHICLE APPLICATIONS Manufacturer Model Engine Year Audi S1 2.0 2014>   Notes: Simple replacement of the OEM part Only fits Right-hand drive vehicles.  Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

Revo Big Brake Kit Upgrade Improves stopping power under any condition OVERVIEW The Revo Big Brake Kit Upgrade is engineered to improve your stopping power in any condition. Whilst stock brakes are perfectly adequate for general driving; the braking system is often overlooked when enhancing a vehicle's performance. This Revo brake kit has been manufactured in conjunction with world-leading brake manufacturer Alcon; utilising over 30 years of motorsport braking innovation only the best materials, techniques and processes have been used. In-depth testing is a key factor in the development of our products; our brake kits have been aggressively tested in a variety of conditions in both road and track scenarios to ensure they meet the constant high stress of track days, sprints and fast road driving. Test kits were installed on our in-house development vehicles along with several vehicles around the world and put through their paces to prove their worth over the stock setup; providing exceptional performance combined with consistency and durability you can rely on, corner after corner, stop after stop. BENEFITS Low Rotational Mass Improved Pedal Responsiveness Lower Long-term Maintenance Costs Superior Heat Dissipation: Less Prone To Fade Increased Braking Performance On & Off Track CALLIPERS Our lightweight four-pot calliper is a single-piece aluminium Mono-bloc design. This design has been used to maximise rigidity, pedal feel, and overall braking performance. The calliper incorporates a progressive four-piston setup to give great brake balance, and high quality seals increasing resilience to road salts and other corrosive elements. DISCS We use a two-piece floating disc and hat design to efficiently dissipate heat. The friction surface features crescent grooves designed to increase bite and remove debris from the pad surface giving the perfect balance between brake feel and longevity. The discs feature internal cooling vanes that draw air from the centre of the disc outward to maximise heat dissipation and minimise heat transfer to the callipers, pads, and brake fluid, which plays an all-important part in providing consistent stopping power for your vehicle. BRAKE PADS We supply our brake kit with Ferodo DS Performance Pads that offer a consistent pedal feel and fantastic braking performance both from cold and when hot. Combined with low wheel dusting, minimal noise characteristics, and low disc and pad wear rates this is the ideal pad compound for general road and track driving. BRAKE LINES Our brake kit is supplied with stainless lines; consisting of a PTFE inner and stainless steel braided outer to eliminate the spongy feel of original rubber hoses, provide superior resistance to corrosion, and offer consistent braking performance. BRAKE FLUID Our brakes are supplied with Motul Dot 5.1 brake fluid; specifically designed for brake systems with ABS. This is a long-life synthetic brake fluid with superior boiling point qualities to conventional Dot 3 and 4 spec. fluids.   KIT CONTENTS Revo by Alcon Caliper x2 Revo by Alcon Discs x2 6061 Aluminium Anodised Bell x2 6061 Aluminium Anodised Caliper Bracket Revo Stainless Steel Braided Brake Lines Motul Dot 5.1 Brake Fluid Ferodo DS Performance Brake Pads   TECHNICAL DOCUMENTS The following documents are available to view: BIG BRAKE KIT TEMPLATE Download the Revo Big Brake Fitting Template   FITMENT      Manufacturer Model Engine Year Audi S1 2.0 TSI 14 -   Notes: Recommended Revo Authorised Dealer Fitment only.  Please contact your local Revo Authorised Dealer for additional information and availability. © Revo

Read more less

OPEN CONE INTAKE The Revo open cone Air Intake System for the 3.0 TFSI engine improves performance and offers an aggressive intake sound. Ensuring your engine can get access to enough air is paramount when increasing power; more air means more power throughout the rev-range. Only Revo Air Intake Systems are specifically designed to work in harmony with your vehicle and Revo Software. Engineered to directly replace the stock airbox, pipework and filter. This kit comes complete with a ceramic coated pipe, heat shield, filter and fitting kit. KEY FEATURES Increased Performance Improved Air Flow Efficiency Ceramic Coated Three Stage Foam Filter with Mesh Lowers Air Intake Temperatures OEM VS REVO When you begin to enhance performance, the restrictive OEM intake struggles to flow enough air, robbing the engine of power. The Revo Air Intake System removes these restrictive elements promoting smoother airflow. Open Cone systems replace the OEM air box to make space for the heat shield, filter and ceramic coated pipe which joins directly to the throttle body. Revo Flush Fit silicone hoses mean joins eliminate unwanted turbulence and increase the rate at which air can flow, ensuring maximum performance at any level of performance. PIPE The Revo intake pipe is designed to directly replace the plastic corrugated parts. The single-piece mandrel-bent aluminium intake pipe reduces turbulence and internal restrictions. The mandrel-bent angles result in no loss of cross-sectional area and allow increased airspeed through the intake. CERAMIC COATING The Revo intake pipe is coated with a Zircotec ceramic coating. Ceramic coatings act as a thermal barrier, reducing the transfer of engine bay temperature to the intake pipe and helping to keep intake air cooler. The coating also allows the pipe to cool at a faster rate, which is important when running more power. HEATSHIELD Ensuring the engine has access to cold air is vital for performance. The Revo heat shield channels cold air from the front intake duct while partitioning the filter from the heat of the engine bay. The Revo Heatshield uses the stock mounting points to provide an easy and secure installation. FILTER An intake system is only as good as the filter. This kit comes complete with a custom Revo foam filter, supported by galvanised epoxy-coated mesh for strength under load. Revo three-stage foam filters work very differently to conventional paper or cotton-gauze alternatives designed to trap particles on the outer layer. Revo filters trap debris and particles within the foam layers, allowing air to still navigate through. The filter is also reusable.   RESEARCH AND DEVELOPMENT All Revo products are designed in-house and are rigorously tested utilising an in-house 3D printer, latest CAD and CFD programs, hub dyno and Revo data acquisition software. The Revo intake allows the turbo to run more efficiently, intake a larger volume of air and minimise turbulence to increase both power and torque, as highlighted during controlled Dyno testing.   PERFORMANCE DATA Back to back testing of the stock air intake system and the Revo kit were carried out. Fitted to an Audi S5 3.0 TFSI B8.5 with Revo ECU Software, Revo Charge Cooler and Pulley upgrade. The results were a power gain from 3900 to 6800rpm, the Revo intake offering a peak gain of 20HP at the hubs, and 9NM torque over the stock part. A maximum increase in airflow of up to +16 kg/hr gives impressive gains of 27HP @6100rpm and 30NM @4600RPM over using the stock intake system. LOWERING TEMPERATURES To show the efficiency of the ceramic coating as a thermal barrier, extra temperature sensors were placed at the filter and throttle body. After 5 dyno runs the maximum IAT (Intake Air Temperature) were 25% lower at the throttle body over the stock intake system. The Revo kit was able to keep temperatures lower than the stock system as well as dissipating heat more efficiently.     FITMENT      Manufacturer Model Engine Year Audi S4(B8/8.5) 3.0 TFSI 2009 - 2016 Audi S5(B8/8.5 3.0 TFSI 2009 - 2016 Audi Q5 3.0 TFSI 2013 - 2017 Audi SQ52 3.0 TFSI 2013 - 2007   Notes: Simple replacement of the OEM part US Models only. Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

Revo Big Brake Kit UpgradeImproves stopping power under any condition OVERVIEW The Revo Big Brake Kit Upgrade is engineered to improve your stopping power in any condition. Whilst stock brakes are perfectly adequate for general driving; the braking system is often overlooked when enhancing a vehicle's performance. The Revo brake kit is made by world-leading brake manufacturer Alcon; utilising over 30years of motorsport braking innovation only the best materials, techniques and processes have been used. In-depth testing is a key factor in the development of our products; our brake kits have been aggressively tested in a variety of conditions in both road and track scenarios to ensure they meet the constant high stress of track days, sprints and fast road driving. Test kits were installed on our in house development vehicles along with several vehicles around the world and put through their paces to prove their worth over the stock setup; providing exceptional performance combined with consistency and durability you can rely on, corner after corner, stop after stop. Made by world leading brake manufacturer Alcon, only the best materials, techniques and processes have been used, with every step of the manufacturing process completed in the UK. Alcon has been at the forefront of motorsport braking innovation for over 30 years. BENEFITS Low Rotational Mass Improved Pedal Responsiveness Lower Long-term Maintenance Costs Superior Heat Dissipation: Less Prone To Fade Increased Braking Performance On & Off Track 380mm x 32mm Disc 100 - 0 MPH AVERAGE STOPPING DISTANCE CALLIPERS Our lightweight six-pot calliper is a single-piece aluminium Mono-bloc design. This design has been used to maximise rigidity, pedal feel and overall braking performance. The calliper incorporates a progressive six-piston setup to give great brake balance, and high quality seals increasing resilience to road salts and other corrosive elements. DISCS We use a two-piece floating disc and hat design to efficiently dissipate heat. The friction surface features crescent groves designed to increase bite and remove debris from the pad surface giving the perfect balance between brake feel and longevity. The discs feature internal cooling vanes that draw air from the centre of the disc outward to maximise heat dissipation and minimise heat transfer to the callipers, pads, and brake fluid, which plays an all-important part in providing consistent stopping power for your vehicle. BRAKE PADS We supply our brake kit with Ferodo DS Performance Pads that offer a consistent pedal feel and fantastic braking performance both from cold and when hot. Combined with low wheel dusting, minimal noise characteristics, and low disc and pad wear rates this is the ideal pad compound for general road and track driving. BRAKE LINES Our brake kit is supplied with a Goodridge Brake line kit with stainless lines; consisting of a PTFE inner and stainless steel braided outer to eliminate the spongy feel of original rubber hoses, provide superior resistance to corrosion, and offer consistent braking performance. BRAKE FLUID Our brakes are supplied with Motul Dot 5.1 brake fluid; specifically designed for brakes systems with ABS. This is a long-life synthetic brake fluid with superior boiling point qualities to conventional Dot 3 and 4 spec. fluids. KIT CONTENTS Revo by Alcon Caliper x2 (3.3 Kg Each) Revo by Alcon Discs x2 (7.66 Kg Each) 6061 Aluminium Anodised Bell x2 6061 Aluminium Anodised Caliper Bracket Goodridge Stainless Steel Braided Brake Lines Motul Dot 5.1 Brake Fluid Ferodo DS Performance Brake Pads   FITMENT      Manufacturer Model Engine Year Audi TT RS  2.5 TFSI  2009 - 2014   Notes: Recommended Revo Authorised Dealer fitment only.  Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

The Autotech HPFP Kit can achieve flow rates 50% higher than the original pump, essentially removing pump limitations from the equation, even on high-end turbo upgrades. Autotech HPFP kit continues to be the benchmark that imitators strive to reach. However, Autotech’s HPFP Kit is not easily duplicated. There are many reasons why Autotech’s Kit is superior. This is what Autotech had to say: ~Each piston (9.8mm) and cylinder in Autotech HPFP kit undergo high-precision grinding processes many times during their manufacture, ensuring that the most precise tolerances are maintained through the final step. Not the cheapest way to make them, but the best way.~Each piston and cylinder are match-ground and serialized to ensure absolute precision and the utmost longevity.~Autotech was the first to incorporate plasma DLC coating on HPFP components to reduce friction losses and increase performance. Others have tried to follow by adding a coating to their parts. However, the DLC process alone is not enough – it is not a cure for substandard precision – the parts must be engineered specifically for the process to take full advantage: Autotech’s are. The success we have in the field can attest to that. Revo trusts Autotech’s HPFP in their conversions and upgrades because it works, and works well. We strongly recommend that you purchase a new Cam Follower and O-Ring Seal, replacing these at the time of installing the Autotech internals. Notes: Recommended Revo Authorised Dealer fitment only.  Please contact your local Revo Authorised Dealer for additional information and availability. © Revo

Read more less

Overview The Revo Carbon Air Scoop is designed to work in harmony with Revo software to unleash the maximum potential from your engine. Flow testing of the OEM intake emphasised the restrictions in the system, giving the Revo engineers a clear indication of what needed improving. The stock front panel used to direct air to the airbox, the standard air filter and convolutions in the rear pipe from the airbox to turbo were found to be the main ‘choking points’ in the system. The Revo system is a direct replacement kit and includes a beautiful carbon front panel, designed to direct cold air directly to the OEM airbox utilising an internal fin, along with the second feed of cold air into the engine bay to help keep ambient temperatures lower. A coolant relocation hose is also included. BENEFITS Improved Performance Carbon Series Quality Less Restriction Direct Replacement Kit   CARBON AIR SCOOP CARBON AIR SCOOP The Revo carbon front section integrates a direct cold air feed which is blanked off on the standard part, and also includes an internal fin that directs air towards the airbox. Designed to also aid in lowering ambient engine temperatures, the Revo engineering team have integrated a second air inlet to allow a direct cold air feed to the engine bay. MORE AIR FLOW Manufactured using the highest quality materials, the Revo carbon front section directly replaces the standard plastic part. A high gloss carbon finish coupled with impressive performance benefits offers a product that delivers in form and function, looking great in the engine bay yet still performing above and beyond the OEM part.   RELOCATION HOSE The Revo Coolant Relocation Hose offers a high-quality single piece replacement for the OEM part which redirects the hose under the front air scoop to give a more aesthetically pleasing look.   TESTING MORE AIR, LESS RESTRICTION Testing was carried out with consistent conditions on both the OEM intake and the Revo Carbon Air Scoop with ProPanel filter, replacement silicone hose, and stock turbo inlet elbow. The graphs below were produced with products fitted to a vehicle and also in a standalone test off the car. The Revo system was tested on a flow bench to highlight the efficiency of the kit in allowing more air to reach the turbo, quickly and with less restriction. The OEM system reached its maximum potential of 440 cubic feet per minute, compared to the Revo system which was able to flow 480 CFM with a restriction of around 600 mmWg. This difference allows the engine to still make power at the top of the rev installing with the Revo kit.   INCREASED POWER AND TORQUE The Carbon Air Scoop (with silicone back hose and ProPanel) was installed on a variety of stage 2 & 3 vehicles, all tested on a 4-wheel hub dyno. Three consecutive runs were carried out on each vehicle comparing the stock system to the Revo MQB Carbon Air Scoop. A consistent gain of +10WHP was found on the 300ps 2.0TSI and +17WHP on the 220ps 2.0TSI, with both giving an average gain throughout the rev range of +16NM torque. It was also noted that with the greater flow of air the turbo was able to spool a lot more quickly giving enhanced throttle response.   FITMENT   Manufacturer Model Engine Year Audi S3 (8v) 2.0 TFSI 12 - Audi TT 2.0 TFSI 15 - Audi TTS 2.0 TFSI 15 - Audi A3 (8v) 1.8 / 2.0 TFSI 12 - Seat Leon Mk3 1.8 / 2.0 TSI 12 - Skoda Octavia Mk3 1.8 / 2.0 TSI 12 - Skoda Superb Mk3 2.0 TSI 15 - VW Golf MK7 2.0 TSI (GTi/R) 12 -   Revo Carbon Series air intake systems perform beautifully. Designed to function no matter the power, Carbon Series intakes look great because of their effective design. Click to find out more   Notes: Simple replacement of the OEM part Please contact your local Revo Authorised Dealer for additional information and availability. 

Read more less

REVO CARBON SERIES - AIR BOX LID The Revo Carbon Lid and turbo inlet hose have been designed and engineered to directly replace the stock airbox lid, pipe and elbow found in vehicles with the 1.8 and 2.0 TSI engines with an IHI turbo. The Revo Carbon Lid offers a high-quality replacement, with its contoured design it not only just aesthetically pleasing but designed to improve airflow and performance of your vehicle. KEY FEATURES Increased performance & airflow Carbon Series Quality Engineered for both LHD and RHD fitment 16% Larger airbox outlet OEM VS CARBON INTAKE With ample efficiency for a stock vehicle, the OEM system quickly becomes a choking point for the engine when running Revo Software. The Revo Carbon Lid has been designed to increase airbox volume and promote smoother airflow. The closed air system helps eliminate heat soak whilst directing cold air through its curved design directly to the oversized outlet. With a 16% larger outlet, the Carbon Lid drastically improves the rate at which air can flow, ensuring maximum performance at even Stage 3 specification.   SILICONE HOSE DESIGN The Revo Turbo Hose as an increased inner diameter to match the large carbon lid outlet that then gradually tapers to the turbo to optimise airflow, while maintaining the tolerances required to fit both LHD and RHD vehicles. Designed to replace the plastic hose and turbo elbow, this upgrade reduces restriction and maximises smooth airflow improving both power and torque throughout the rev range. TURBO INLET The Revo machined inlet replaces the restrictive elbow found on the IS20/IS38 turbos. The billet aluminium piece securely fits the OE unit using locking tabs and integrated O-rings. With almost double the cross-sectional area compared to other available products, air can stabilise and distribute before a smooth tapered transition to the turbo. Removing the internal steps between components ensures smooth and linear airflow transition between elements, providing uninterrupted airflow and removing any unnecessary turbulence.     RESEARCH AND DEVELOPMENT All Revo products are designed and rigorously tested in-house utilising 3D printed prototypes, latest CAD and CFD programs, 4 wheel hub dyno and Revo developed data acquisition software. The Revo Carbon lid and Turbo Inlet Hose allows the Stock IS38/IS20 turbo to run more efficiently, by maximising air volume and minimising turbulence you increase power and torque, especially at the top end of the rev range as highlighted during controlled Dyno testing.  Read more     GRAPHS   FITMENT   Manufacturer Model Engine Year Audi A3 (8V) 1.8 / 2.0 TFSI 12 - Audi S3 (8V)/td> 2.0 TFSI 12 - Audi TT (MK3) 2.0 TFSI 15 - Audi TTS (MK3) 2.0 TFSI 15 - Seat Leon (MK3) 1.8 / 2.0 TSI 12 - Skoda Octavia (MK3) 1.8 / 2.0 TFSI 12 - Skoda Superb 2.0 TSI 15 - Volkswagen Golf (MK7) 2.0 TSI GTI 12 - Volkswagen Golf (MK7) 2.0 TSI R 12 - Volkswagen Golf (MK7) 1.8 TSI 12 -  

Read more less

SECONDARY AIR PUMP ADAPTOR The OEM secondary air feed, designed to lower emissions during cold start was found to cause turbulence during testing of the standard airbox. To combat this, we created a standalone Secondary Air Breather with an integrated three-stage foam filter to supply the electric pump fitted to certain models. If your engine has this feed then this product is required with the Carbon Lid Kit. KEY FEATURES Used with Carbon Series MQB Lid Required for Vehicles with Secondary Air Injection CNC Machined Housing Support Bracket   MACHINED HOUSING Designed to replace the plastic OEM part from the stock airbox lid, the Revo Secondary Air Pump Adaptor is made from 6061 T6 black anodised aluminium to avoid corrosion. With a built-in three-stage foam filter and a multiple hole design to ensure the filter does not collapse, the secondary air pump can efficiently receive a filtered air supply. BRACKET The 2mm thick 304 powdered coated stainless steel bracket offers resistance against engine vibrations and excess movement, designed to secure the breather housing in place without it damaging the carbon lid or disrupting airflow or aesthetics.   FITMENT This product is designed to be installed with the Revo Carbon Series MQB Lid and hose kit VEHICLE APPLICATIONS Manufacturer Model Engine Year Volkswagen Audi Group Multiple 2.0 TSI with Secondary Air Injection 2014>   Notes: Simple replacement of the OEM part Please contact your local Revo Authorised Dealer for additional information and availability. © Revo

Read more less

Revo Charge Cooler System OVERVIEW The Revo Charge Cooler System is a direct replacement kit that offers enhanced cooling capabilities to maximise the performance of your vehicle. The Audi 3.0T V6 engine is a compact power plant before tuning, with Revo Stage 1+ Software and a Revo Pulley upgrade you can expect to see figures up to 442BHP (415PS, 330KW) and 610NM (450LBFT) of torque throughout the rev-range, transforming an already powerful car. The supercharger on the 3.0T engine shares the coolant system with the rest of the engine, this causes temperatures to rapidly climb when driven at high speed for long periods or in hotter climates, these high temperatures cause the car to reduce power as a safety parameter, resulting in loss of performance. The Revo Charge Cooler System enhances the engines cooling capabilities, giving access to more power for a longer period of time. The direct-fit standalone system has unique features that optimise the entire cooling system, a larger heat exchanger, the addition of a dedicated coolant reservoir and custom silicone hoses and fixing brackets. The Revo Charge Cooler System offers more consistent and lowers intake temperatures, especially at the top end of the rev range. BENEFITS Standalone System Lowers Intake Temps By Up To 16.5 °C 50% Larger Heat Exchanger Direct Replacement Kit HEAT EXCHANGER MORE SURFACE AREA To achieve more effective cooling, the heat exchanger has a much larger surface area than the OEM part and has over 50% more volume. The increased amount of coolant within the system means it has more to work with, effectively slowing down how quickly the OEM pump needs to move the coolant around and giving it more time to cool in the heat exchanger. OPTIMISED END TANKS The Revo engineers did not want to only increase the size of the cooler, but to ensure that it operated more proficiently than the stock part. Each end tank has been designed with specifically placed bars that evenly distribute coolant throughout the cooler, allowing more time for it to dissipate heat while in the core. RESERVOIR STANDALONE SYSTEM As a standalone system with a dedicated reservoir, the Revo Charge Cooler System operates far more efficiently, introducing more coolant to the system and reducing pressure on the OEM coolant pump. Dedicated to cooling the Supercharger alone, the Revo system also allows the rest of the engine to cool itself more efficiently. The system has been designed with subtlety in mind and will fit directly into the engine bay without any need for modifying. BRACKETS AND HOSES SILICONE HOSES As well as the brackets and fixings, the Charge Cooler Kit also comes with Cad designed silicone hoses to re-route the coolant. Manufactured using automotive-grade silicone and the highest quality polyester fabric, the hoses are built with four plies to ensure optimum strength and reliability. TESTING COOLER TEMPERATURES Temperature testing was carried out to ensure that the new Revo system was doing its job. Carrying out consecutive high-speed runs of 0-160mph, the team were able to mimic the extreme scenarios that result in high intake temperatures and subsequently a loss of power. This was done at a private test track rather than on a dyno to ensure airflow was realistic. It was also noted that when at normal driving speeds there was a reduction in intake temperatures of between 3-6°C with the Revo charge cooler fitted, compared to the same run with the OE cooler. The graph shows the 1st and 5th of 5 back to back runs with both the stock heat exchanger and the Revo Charge Cooling System. Each run was 0-160mph and air temperatures ranged from 17 - 20°C, with the Revo charge cooler system remaining 12° C cooler than the Stock system after the 1st Run.   FITMENT   Manufacturer Model Engine Year Audi S4 (B8.5) 3.0 V6 TFSI 2012 > Audi S5 (B8.5) 3.0 V6 TFSI 2012 >   Notes: Simple replacement of the OEM part 2012 is the B8.5 release for the UK Market. Other countries release date may vary. Does not fit vehicles with Audi "Drive Select" Please contact your local Revo Authorised Dealer for additional information and availability. © Revo

Read more less

FOCUS ST MK4 | OPEN CONE INTAKE SYSTEM The Revo Ford Focus ST Mk4 Open Cone Air Intake Systems completely replace the OEM air intake for those who like to announce their vehicle is far from standard. Along with an aggressive intake sound, more air means access to more power throughout the rev-range. Fitting Guide REVO OPEN CONE AIR INTAKE SYSTEM FORD FOCUS ST MK4 2.3 ECOBOOST  The Revo Open Cone Air Intake System for the Focus ST MK4 2.3 EcoBoost improves performance and offers an aggressive intake sound. Ensuring your engine can get access to enough air is paramount when increasing power; more air means more power throughout the rev range. Only Revo Air Intake Systems are specifically designed to work in harmony with your vehicle and Revo ECU Software. Engineered to directly replace the stock airbox, pipework and filter, this kit comes complete with a turbo inlet silicone hose, aluminium pipe, silicone Intake hose, heat shield, filter and fitting kit. KEY FEATURES Massive increases in performance Improved airflow efficiency Average gains of +26WHP Direct filter to turbo fitment Stepped silicone for smooth airflow   OEM VS REVO When you begin to enhance performance, the restrictive OEM intake struggles to flow enough air, robbing the engine of power. The Revo Air Intake System removes these restrictive elements promoting smoother airflow. Open Cone systems replace the OEM airbox to make space for the heat shield, filter and pipework which joins directly to the turbo. Revo Flush Fit silicone hoses avoid unwanted turbulence at joins and increase the rate at which air can flow ensuring maximum performance at any level of tuning. SILICONE HOSES No detail has been overlooked when reducing restrictions within the stock airflow system. The stock corrugated plastic hose is replaced with a smooth silicone one, reducing air turbulence and increasing air volume and speed. A four-ply construction with an internal wire helix increases strength to prevent collapsing under pressure. Internal steps flush fit against the hard pipe section and turbo inlet, creating a smooth transition between components and ensuring the smoothest airflow.   TURBOCHARGER INLET HOSE The integrated sound suppression chamber of the OEM pipe has been removed, allowing for significantly more laminar airflow. The Revo inlet hose geometry allows faster air delivery to the turbo by smoothing the harsh 90° transition part of the stock pipe. Also removing the internal steps between components further ensures uninterrupted airflow and removes any unnecessary turbulence.   ALLOY HARD PIPE The Revo mid-section hard pipe offers a smoother internal geometry over the stock part it replaces, all contributing to the increased performance benefits of the Revo Intake. The pipe has been designed to match the same mounting and vacuum take-off points, ensuring a direct fitment product.   AIR FILTER An intake system is only as good as the filter. This kit comes complete with a custom Revo Foam Filter, supported by galvanised epoxy-coated mesh for strength under load. Revo three-stage foam filters work very differently from conventional paper or cotton-gauze alternatives designed to trap particles on the outer layer. Revo filters trap debris and particles within the foam layers, allowing air to still navigate through. The spun base of the filter offers a smooth radius aluminium bell mouth, specifically designed for optimum airflow from the filter to pipe-work. HEAT SHIELD Ensuring the engine has access to cold air is vital for performance. The Revo Heat Shield channels cold air from the front intake duct while partitioning the filter from the heat of the engine bay. The Revo Heat Shield uses precise machined pins to locate to the stock mounting points to provide an easy and secure installation.     RESEARCH AND DEVELOPMENT All Revo products are designed in-house and are rigorously tested utilising an in-house 3D printer, the latest CAD and CFD programs, hub dyno and Revo data acquisition software. The Revo Intake allows the turbo to run more efficiently, intake a larger volume of air and minimise turbulence to increase both power and torque, as highlighted during controlled dyno testing. The Revo Focus ST MK4 Open Cone Air Intake System was tested in-house to compare the performance against that of the Ford OEM Intake. First tested on a vehicle running the OEM intake with Revo Software, the Revo Intake was then installed and tested in the same controlled environment to highlight the benefits of increasing airflow flow and speed. PERFORMANCE DATA The results show improvement throughout the whole rev range, with huge performance increases. Showing just how restrictive the stock system is when looking to upgrade the performance of your ST. The Revo Intake offers an average gain of +26WHP, and +43NM torque over the stock part. Increased airflow also delivers impressive peak performance gains of +54WHP @5100rpm and +75NM @5100RPM over the stock intake system.     FITMENT VEHICLE APPLICATIONS Manufacturer Model Engine Year Ford Focus ST MK4 2.3 EcoBoost 2018 onwards NOTES Simple replacement of the OEM part

Read more less

REVO OPEN CONE AIR INTAKE SYSTEM FORD FIESTA ST MK8 1.5 ECOBOOST The Revo open cone Air Intake System for the 1.5 EcoBoost engine improves performance and offers an aggressive intake sound. Ensuring your engine can get access to enough air is paramount when increasing power; more air means more power throughout the rev-range. Only Revo Air Intake Systems are specifically designed to work in harmony with your vehicle and Revo ECU Software. Engineered to directly replace the stock airbox, pipework and filter, this kit comes complete with a front silicone hose, aluminium pipe, heat shield, filter, turbo inlet silicone and fitting kit. KEY FEATURES Increased Performance & Air Flow Efficiency Three Stage Foam Filter Direct filter to turbo fitment Stepped Silicone for smooth airflow   OEM VS REVO When you begin to enhance performance, the restrictive OEM intake struggles to flow enough air, robbing the engine of power. The Revo Air Intake System removes these restrictive elements promoting smoother airflow. Open Cone systems replace the OEM air box to make space for the heat shield, filter and pipework which joins directly to the turbo. Revo Flush Fit silicone hoses avoid unwanted turbulence at joins and increase the rate at which air can flow ensuring maximum performance at any level of tuning. CROSS OVER PIPE The Revo engineering team knew that to create the most effective kit, every component had to be considered to maximise and smooth airspeed. The system is designed around the single-piece aluminium cross over pipe, mandrel-bent to maintain the internal diameter in the corner and to remove the restrictions found in the OEM pipe. The direct routing and increased diameter pipe offer superior flow and deliver more air to the turbocharger over a shorter period.   SILICONE HOSES The plastic hoses on the stock system are designed with a corrugated style to flex with the engine movement, while this has its place it also causes a large amount of turbulence as the airflow doesn’t have a smooth direct path to the turbo. We designed the silicone hoses with stepped internals to ensure a flush fit and to minimise turbulence while still allowing for engine movement. The turbo inlet hose has an increased inner diameter that gradually tapers from the hard pipe to turbo to optimise airflow.   AIR FILTER An intake system is only as good as the filter. This kit comes complete with a custom Revo foam filter, supported by galvanised epoxy-coated mesh for strength under load. Revo three-stage foam filters work very differently to conventional paper or cotton-gauze alternatives designed to trap particles on the outer layer. Revo filters trap debris and particles within the foam layers, allowing air to still navigate through. The spun base of the filter offers a smooth radius aluminium bell mouth, specifically designed for optimum airflow from the filter to pipe-work.   HEATSHIELD Ensuring the engine has access to cold air is vital for performance. The Revo heat shield channels cold air from the front intake duct while partitioning the filter from the heat of the engine bay. The Revo Heatshield uses the stock mounting points to provide easy and secure installation. MOUNTING BRACKET AND FITTING KIT The Revo kits come complete with a full fitting kit that allows for easy installation. Included is a fully machined crossover bracket which increases the strength of this fixture point and alleviates any possibility of bracket failure from engine movement. RESEARCH AND DEVELOPMENT All Revo products are designed in-house and are rigorously tested utilising an in-house 3D printer, latest CAD and CFD programs, hub dyno and Revo data acquisition software. The Revo intake allows the turbo to run more efficiently, intake a larger volume of air and minimise turbulence to increase both power and torque, as highlighted during controlled dyno testing. The Revo Fiesta Mk8 open cone air intake system was tested in-house to compare the performance against that of the Ford OEM intake. First tested on a vehicle running the OEM intake with Revo Stage 1 software, Revo Intercooler and a Milltek GPF back exhaust, the Revo intake was then installed and tested in the same controlled environment to highlight the benefits of enhanced cooling. PERFORMANCE DATA The results show improvement throughout the whole rev range, but especially towards the top end of the rev range. The Revo intake offering an average gain of +7WHP, and +11NM torque over the stock part. Increased airflow also delivers impressive peak performance gains of +14WHP @6200rpm and +19NM @5100RPM over the stock intake system. AIRFLOW More air, less restriction. The Revo system was tested on a flow bench to highlight the kits efficiency in allowing more air to reach the turbo, quickly and with less restriction. The OEM system reached its maximum potential of 490 cubic feet per minute with a restriction of 1082 mmWg, compared to the Revo system which was able to flow 700 CFM with a restriction of only 965 mmWg. This difference allows the engine to still make power at the top of the rev limit, whilst also highlighting the efficiency and less restriction at the lower end, resulting in smoother and increased throttle response.     FITMENT VEHICLE APPLICATIONS Manufacturer Model Engine Year Ford Fiesta ST 1.5 EcoBoost 2018 onwards DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the Revo Ford Fiesta MK8 ST Open Cone Intake System Instructions NOTES Simple replacement of the OEM part

Read more less