Performance - Skoda Octavia MK4 NX 2020-PRESENT

State of art polymer laminated glass cloth Superb heat barrier qualities Withstands radiant temperatures up to 450°C/850°F Ultra thin for minimal clearance As used in WRC and F1 Each roll is 50mm wide x 5 metres long (2" x 16ft) Adhesive backing for ease of fitting After extensive market research Forge Motorsport are proud to release a state of the art metalized polymer laminated glass cloth with adhesive backing that is both extremely light and capable of handling continuous radiant temperatures of up to 450°C. It reflects up to 80% of all radiant heat, whilst offering weight savings against other heat reflecting materials. Forge Motorsport's gold reflective heat barrier requires minimal clearance and is an extremely pliable material with a pressure sensitive adhesive backing that is easy to apply and remove. As used in WRC and F1, make no mistake this gold reflective heat barrier tape is of excellent quality and superb value for money. When used correctly this tape can be used to protect intake components thus lowering IATs resulting in a more efficient and reliable engine cycle. Typical uses are: Wrapping wiring, inside engine covers, bulkheads and firewalls, boost pipes, fuel lines, under seats, intake pipes, airboxes, engine compartments, fuel cells…  

Read more less

2.0 TSI EA888 gen.4 Garrett Turbo 245PS Turbo Inlet SystemTurbo 90 Inlet & Silicone Inlet Hose. RACINGLINE TURBO INLET ELBOW FOR 2.0 TSI EA888.4 245PS GOLF 8 GTI, LEON CUPRA FW, AUDI A3 8Y, OCTAVIA vRS NXVWR120003 For VW, Audi, Cupra 'lower output' 245PS / 207PS (Garrett Turbo)Golf mk8 GTI, Cupra Leon, Cupra Formentor, Octavia vRS & more. Release power with the 2.0 TSI gen 4 Turbo Inlet System. A significantly enlarged airflow path from intake straight into turbo.For the Garrett turbo (lower output) 245ps engines such as Golf 8 GTI, Cupra Leon & Formentor and Octavia vRS, plus 207ps Polo GTI AW.2 What the turbo inlet system does.  The RacingLine Turbo Inlet System for the 245PS & 207PS MQB 'EVO' cars such as Golf 8 GTI is a matched package of our much larger diameter, free flowing Turbo 90 Inlet paired with reinforced Silicone Turbo Inlet Hose for much higher airflow between intake and turbo. The factory inlet forces the airflow to pass through the restrictive plastic 'bellows' pipe, before tapering right down to run through a tight and restrictive plastic turbo inlet - in other words, terrible for flow.  The RacingLine Turbo Inlet System replaces this pipework with a larger diameter smooth-flowing silicon hose mated to a larger diameter thin-wall free flowing intake elbow. The internal diameter of the Turbo 90 Inlet is massively increased from 62.5mm on the factory part right up to 76mm. It's by combining the two parts of the kit that's allowed us to enlarge the diameter of both the Inlet and the Hose so much - and so give the maximum possible gains. Put simply, without it, you’re wasting much of the potential of your high-flow intake system without fitting this Turbo Inlet System. An essential upgrade! TWO PIECE KIT It's only by combining both elements of this kit that we've been able to increase the diameter so significantly (+13.5mm) to release the true airflow gains.  POWER GAINS The ultra-thin wall High-Flow Turbo 90 Inlet features an internal velocity stack to maximise airflow capability through to the turbo's inlet. EASY FIT Fitting is straightforward. The kit is installed in around 30minutes using just hand tools.   And easily returned to standard, should you ever wish.  PRECISION ENGINEERED FOR PERFECT PERFORMANCE. Reinforced high quality silicone prevents deformation under load or heat Flexible enough to allow just the right amount of engine movement under load Internally-stepped silicone to ensure smooth transitions CNC constructed from T6-6061 aircraft grade aluminium with Viton sealing O-ring Maximum 80mm outer diameter with ultra-thin wall 2mm tube, smoothed internal bore Polished then anodised in gloss black to look good, and stay looking good. CONFIRMED APPLICATIONS For 245ps & 207PS EA888.4 (Garrett turbo) engines:VWR120003 > VW Golf 8 GTI 2020+ > VW Polo 6 GTI 2.0 TSI 207ps AW.2 2021+ > Audi A1 Competition 207ps 40TFSI GB 2021+ > Audi A3 2.0 TSI 8Y 2020+ > Audi TT 45 TFSI 8S 245ps (EA888.4) 2021+ > Cupra Leon IV 245 TSI FW 2020+ > Cupra Formentor 245ps 2020+ > SEAT Tarraco 2.0 TSI 245ps 2021+ > Skoda Octavia IV vRS 2.0 TSI 245ps NX 2020+ > Skoda Kodiaq vRS 2.0 TSI 245ps (EA888.4) 2021+

Read more less

2.0 TSI gen 4 EA888.4 245PSTurbo Muffler DeleteFor all VW, Audi, Cupra, Skoda 2.0 TSI gen.4 Choose a smooth, turbulence-free air path exiting your turbo with the RacingLine 2.0 TSI Turbo Muffler Delete.For the Garrett turbo (lower output) 245ps engines such as Golf 8 GTI, Audi A3/TT, Cupra Leon and Octavia vRS and more. What the gen.4Turbo Muffler Deletedoes. Our Tapered Turbo Muffler Delete for 2.0 TSI EA888.4 245ps is a sleek single billet design combined with larger diameter silicone joiner hose which replaces the restrictive, power-robbing compressor outlet with a smooth, turbulence free air path exiting the turbo. The standard part is located on the outlet of the turbo compressor to reduce engine bay acoustics, but adds in disruptive turbulence to the airflow right where you don't want it.  The OEM part is a 38mm inner diameter throughout, whilst the RacingLine tapered design enlarges up to 53mm, joining perfectly with the smooth 53mm, internally-stepped silicone hose. By replacing the standard part with the tapered Turbo Muffler Delete and Silicone Hose, you’ll replace this unwanted restriction with a smooth CFD-developed uninterrupted air path.  The result: noticeably better boost response giving a little more power and throttle reaction, all the while being able to actually hear your turbo working. FULL KIT This tapered Turbo Muffler Delete comes with Silicone Joiner pipe which enlarges from the OEM 38mm diameter up to 53mm throughout. Supplied with both pipes and fitting clamps. SMOOTH TRANSITIONS By smoothing the airflow path out of the turbo up to the larger 53mm diameter and using an internally-stepped silcone pipe, this massively reduces the restriction and turbulence caused by the OEM part. EASY FIT Fitting is straightforward. The kit is installed in around 30minutes using just hand tools.   And easily returned to standard, should you ever wish. An essential fit with your R600 upgraded intake system. PRECISION ENGINEERED FOR PERFECT PERFORMANCE. CNC constructed from single-piece billet T6-6061 aircraft grade aluminium. Smooth transition up from 38-53mm - removing the restriction caused by OEM turbo muffler delete. Hand polished then anodised in gloss midnight black to look good, and stay looking good. The white laser-etched RacingLine logo is all part of the detail. CONFIRMED APPLICATIONS 2.0 TSI 245ps EA888 gen.4 engines ONLY VWR160000 > VW Golf 8 GTI 2020+ > Audi A3 2.0 TSI 8Y 2020+ > Audi TT 45 TFSI 8S 245ps (EA888.4) 2021+ > Cupra Leon IV 245 TSI FW 2020+ > Cupra Formentor 245ps 2020+ > SEAT Tarraco 2.0 TSI 245ps 2021+ > Skoda Octavia IV vRS 2.0 TSI 245ps NX 2020+ > Skoda Kodiaq vRS 2.0 TSI 245ps (EA888.4) 2021+ Note: not applicable to the higher-output 300+ ps Continental-turbo engines such as Golf 8R, Golf 8 GTI CS, Audi S3 etc

Read more less

STYLE. WITH SUBSTANCE STUNNING CARBON FIBRE LID FOR R600 The RacingLine R600 Intake is the world's most sophisticated and best-selling MQB-platform cold air intake.If you already have an R600, why not add a Carbon Fibre Replacement Lid update to give your existing R600 intake a whole new look.  WHYUPGRADE? If you’re already running an R600 intake, you’ll know that it’s the most sophisticated intake available, combining OEM-standard design & quality with significant power gains.   But there's more good news. This new R600 Carbon Fibre Lid upgrade now gives you a chance to update your existing R600 with a whole new look in the engine bay. A simple replacement for any existing R600 intake lid. Simply unscrew the old lid and replace with the stunning new Carbon replacement. The quality of our carbon weave and finish is second to none. Offered in your choice of either a sophisticated matte finish, or stunning high gloss surface. Each lid is carefully hand-laid using pre-preg carbon fibre - which means we can achieve a smooth internal surface, stunning appearance and perfect fitment. This is supplied as a replacement lid only - to retrofit to any existing R600 intake. SOPHISTICATED MATTE CARBON FIBRE VWR121001 STUNNING HIGH GLOSS​ CARBON FIBRE VWR121000 SIMPLE FIT Fitted in minutes to any existing R600 intake of any age. Simply unscrew the old lid and replace it with the new carbon version. BEAUTIFUL  The exquisite detail of the carbon weave and the flawless surface finish will transform your engine bay appearance. In fact, it's almost a shame to hide it away! STRONG & LIGHT Each R600 lid is carefully hand-laid using autoclaved pre-preg carbon fibre for a strong & light construction with perfect dimensional accuracy. CONFIRMED APPLICATIONS ANY R600 INTAKE FOR 2.0 TSI & 1.8 TSI MQB / EA888.3 / 3B ​ GLOSS LID: VWR121000      MATTE LID: VWR121001 ​ NOTES: This is a lid only, for retro-fitting to any R600 Intake (VWR12G7R600/1/2) of any age. NOTE: this lid does not fit the new MQB 'EVO' intake. The Carbon Lid for this intake is coming soon.

Read more less

R600 AIR INTAKEFOR MQB & MQB 'EVO' The RacingLine R600 Intake is the world's most sophisticated and best-selling MQB-platform cold air intake, with a choice of two filter element types. Now with fitment for the latest MQB EVO models such as Golf 8, Audi S3 8Y etc. Now with the added option of Carbon Fibre Lid - your choice of sophisticated Matte Carbon or stunning Gloss Carbon. WHAT'S SOSPECIAL? Looking for the most sophisticated cold-air intake available for your MQB or MQB 'EVO' 2.0 or 1.8 TSI? The R600 intake is our best selling system for this platform. Little wonder, as it combines OEM-standard design and quality with significant power gains on uprated cars. OEM-standards of design, quality, materials and construction, hand-made in the UK. Fits like a factory part; lasts like a factory part. Twin CFD-optimised front intakes extending across the front of the car help achieve lower intake temperatures and worthwhile power gains. Enormous airbox volume houses the filter, complete with thoughtful details like connection to the original factory drain tube, and an SAI connection for US cars. Your choice of filter unit, to suit different needs. Both are double the size of standard - rated right up to 600hp and beyond. TRIFOAM® FILTER UNIT ​ Faster, for longer The highest airflow of all filter types, for the best possible power for more of the time. As a high performance part, regular maintenance is essential to keep it at its very best. VWR12 G7R600 PLEATED COTTON FILTER ​ Fit and forget A robust 'fit and forget' filter that will last for years. It gives great initial power output but doesn't have the dust-loading capacity of Trifoam. VWR12 G7R601 PRECISION ENGINEERED FOR PERFECT PERFORMANCE. Airbox is UK-moulded in factory specification PU Polyurethane PU gives excellent heat-insulation properties, keeping airbox temps lower. Both of our giant filter units are hand-made in the UK. Choose from Trifoam® or Pleated Cotton Every factory mounting point is retained for that perfect fit. GIANT FILTER UNIT It's your choice. Both our unique Trifoam® filter and new Pleated Cotton units are hand-made in the UK for the perfect filtration and minimum restriction. FULL-WIDTH INTAKE Twin front intakes extending across the front of the car help achieve lower intake temperatures and worthwhile power gains. CFD DESIGNED Airflow is no accident. Fully developed with F1-standard CFD programmes. It's no wonder so many high-power MQB cars choose the R600.   CONFIRMED APPLICATIONS 2.0 TSI MQB 'EVO' / EA888.4 engines  NEW! 2.0 TSI & 1.8 TSI MQB / EA888.3 engines ​ VWR1200R600E   Trifoam filter     VWR1210R600EM  Trifoam filter / Matte Carbon    VWR1210R600EG  Trifoam filter  / Gloss Carbon     VWR1200R601E  Cotton filterVWR1210R601EM  Cotton filter  / Matte Carbon    VWR1210R601EG  Cotton filter  / Gloss Carbon > VW Golf 8 GTI 2020+ > VW Golf 8 GTI Clubsport 2020+ > VW Golf 8 R 2020+ > VW Golf 7 & 7.5 GTI & Clubsport 2013-2020 > VW Golf 7 & 7.5 R 2013-2020 > VW Golf 7 & 7.5 1.8 TSI 2013-2020 > VW Passat 2.0 TSI B8 2015+ > VW Arteon 2.0 TSI 2017+ > VW Arteon R 2.0 TSI 320ps 2020+ > VW T-Roc R 2.0 TSI 2019+ > VW Tiguan II 2.0 TSI 2016+ > VW Tiguan II 2.0 TSI 245ps 2021+ > VW Tiguan II R 2.0 TSI 320ps 2020+ > VW Jetta / GLI 7 2018+ > Audi S3 8Y 2020+ > Audi A3 2.0 TSI 8Y 2020+ > Audi S3 8V 2013-2020 > Audi A3 2.0 TSI / 1.8 TSI 8V 2013-2020 > Audi TT 3 8S 2014+ > Audi TTS 2.0 TFSI 8S 2015-2021 > Audi TT 2.0 TFSI 8S 2014+ > Audi TTS 2.0 TFSI 8S 320ps (EA888.4) 2021+ > Audi SQ2 2018+ > Audi Q3 45 TFSI 2.0 TSI 2018+ > Cupra Leon IV 300 TSI FW 2020+ > Cupra Leon IV 245 TSI FW 2020+ > SEAT Leon III Cupra 5F 2014-2020 > SEAT Leon III 1.8 TSI 5F 2014-2020 > Cupra Formentor 310ps 2020+ > Cupra Formentor 245ps 2020+ > Cupra Ateca 2018+ > SEAT Tarraco 2.0 TSI 2018+ > Skoda Octavia IV vRS 2.0 TSI 245ps NX 2020+ > Skoda Octavia III vRS 2.0 TSI 5E 2014-2020 > Skoda Superb III 1.8 / 2.0 TSI 3V 2015+   CONFIRMED APPLICATIONS 2.0 TSI MQB / EA888 Gen.3B 190 hp engine with MAF VWR12G7R602  Trifoam filter      VWR1210R602M  Trifoam filter  /  Matte Carbon    VWR1210R602G  Trifoam filter  /  Gloss Carbon     VWR12G7R603  Cotton filter VWR1210R603M  Cotton filter  /  Matte Carbon    VWR1210R603G  Cotton filter  /  Gloss Carbon   > VW Passat 2.0 TSI 190hp B8 2018+ > VW Arteon 2.0 TSI 190hp 2017+ > VW T-Roc 2.0 TSI 190hp 2017+ > VW Tiguan II 2.0 TSI 190ps 2018+ > Audi A3 40TFSI 2.0 TSI 190hp 2016-2020 > Audi TT 40 TFSI 2.0 TSI 197hp 2018+ > Audi Q2 40 TFSI 2.0 TSI 190hp 2017+ > Audi Q3 40 TFSI 2.0 TSI 190hp 2018+ > SEAT Leon III 2.0 TSI 190hp 5F 2018+ > SEAT Ateca 2.0 TSI 190hp 2017+ > SEAT Tarraco 2.0 TSI 190ps 2018+ > Skoda Octavia III 2.0 TSI 190hp 5E 2017-2020 > Skoda Superb III 2.0 TSI 190hp 3V 2019+ > Skoda Karoq 2.0 TSI 190hp 2018+ > Skoda Kodiaq 2018+ > Skoda Kodiaq 2.0 TSI 190hp 2018+

Read more less

2.0 TSI & 2.0 TDIHigh-FlowPanel Air Filter. Set your MQB & MQB 'Evo' 2.0 TSI, 1.8 TSI or 2.0 TDI engine free by allowing it to breathe better and operate more efficiently.VWR11G701 What doesit do? Looking for a simple, warranty-friendly upgrade for your car? ​ Our High-Flow Panel Air Filters, available for all Volkswagen Group 'MQB' 2.0 TSI, 1.8 TSI & 2.0 TDI cars, replace the restrictive factory paper filters with an improved, high flow and reusable lifetime triple-layer Trifoam® filter. Put simply, it’s the best Panel Air Filter you can buy. OEM-standards of design, quality, materials and construction, hand-made in the UK. Fits like a factory part; lasts like a factory part Allow your engine to breathe better and operate more efficiently – improve the engine’s airflow, and power and fuel economy gains will follow.  By removing the inevitable restrictions that the standard paper panel filter gives, our Panel Filter allows a small but worthwhile increase in airflow through to the turbo.    TRIFOAM® FILTER Our unique Trifoam® filter construction allows us to sandwich three different foams together for the perfect filtration and minimum restriction. HAND-MADE IN UK Each filter construction is hand-made in the UK for the reassurance of the highest quality together with exceptional dust-loading properties. EFFICIENCY GAINS The result?  More mid-range power and improved economy, without wrecking your warranty PETROL/GAS ENGINES All MQB/MQBE 1.8 & 2.0 TSI DIESEL ENGINES All MQB/MQBE 2.0 TDI   Confirmed applications. VWR11G701All MQB / MQB 'Evo' VW / AUDI / SEAT / CUPRA / SKODA2.0 TSI EA888.3 & EA888.41.8 TSI EA888.32.0 TDI EA288 & EA189 > VW Golf 8 GTI 2020+ > VW Golf 8 GTI Clubsport 2020+ > VW Golf 8 R 2020+ > VW Golf 7 & 7.5 GTI & Clubsport 2013-2020 > VW Golf 7 & 7.5 R 2013-2020 > VW Golf 7 & 7.5 1.8 TSI 2013-2020 > VW Golf 7 & 7.5 2.0 TDI / GTD 2013-2020 > VW Passat 2.0 TDI B8 2015+ > VW Passat 2.0 TSI B8 2015+ > VW Arteon 2.0 TDI 2017+ > VW Arteon 2.0 TSI 2017+ > VW T-Roc R 2.0 TSI 2019+ > VW T-Roc 2.0 TDI 2017+ > VW Tiguan II 2.0 TDI 2016+ > VW Tiguan II 2.0 TSI 2016+ > VW Jetta / GLI 7 2018+ > Audi S3 8Y 2020+ > Audi A3 2.0 TSI 8Y 2020+ > Audi S3 8V 2013-2020 > Audi A3 2.0 TSI / 1.8 TSI 8V 2013-2020 > Audi A3 8V 2.0 TDI 2013-2020 > Audi TT 2.0 TDI 8S 2014+ > Audi TTS 2.0 TFSI 8S 2015-2021 > Audi TT 2.0 TFSI 8S 2014+ > Audi TTS 2.0 TFSI 8S 320ps (EA888.4) 2021+ > Audi SQ2 2018+ > Audi Q2 2.0 TDI 2017+ > Audi Q3 45 TFSI 2.0 TSI 2018+ > Cupra Leon IV FW 2020+ > SEAT Leon III Cupra 5F 2014-2020 > SEAT Leon III 1.8 TSI 5F 2014-2020 > SEAT Leon III 2.0 TDI 5F 2013-2020 > Cupra Formentor 2020+ > Cupra Ateca 2018+ > SEAT Ateca 2.0 TDI 2016+ > SEAT Tarraco 2.0 TSI 2018+ > Skoda Octavia IV vRS 2.0 TSI 245ps NX 2020+ > Skoda Octavia III vRS 2.0 TSI 5E 2014-2020 > Skoda Octavia III vRS 2.0 TDI 5E 2014-2020 > Skoda Octavia III 5E 2.0 TDI 2014-2020 > Skoda Superb III 2.0 TDI 3V 2015+ > Skoda Superb III 1.8 / 2.0 TSI 3V 2015+

Read more less

RACINGLINE R600 EVO COOLANT UNDERHOSE Our R600 EVO Coolant Underhose reroutes the ugly factory hose underneath your beautiful intake for a much cleaner look R600 EVO COOLANTUNDERHOSE PIPEFor VWG 2.0TSI EA888.4 (excluding Golf mk8 R)   PRECISION ENGINEERED FOR PERFECT PERFORMANCE. Reinforced 4-ply reinforced silicone to withstand the high pressures of the coolant system Inner Flouro lining to be compatible with G12 and G13 coolant fluid used on MQB cars Precision moulded to retain the perfect shape for the life of the car Temperature-resistant premium grade silicone rubber will exceed any possible coolant temperatures and keep its rigidity CONFIRMED APPLICATIONS VWR17 G8R600  FOR CARS WITH R600 INTAKE FITTED > VW Golf 8 GTI 2020+ > VW Golf 8 GTI Clubsport 2020+ > VW Arteon R 2.0 TSI 320ps 2020+ > VW Tiguan II 2.0 TSI 245ps 2021+ > VW Tiguan II R 2.0 TSI 320ps 2020+ > Audi S3 8Y 2020+ > Audi A3 2.0 TSI 8Y 2020+ > Audi TT 2.0 TFSI 8S 2014+ > Audi TTS 2.0 TFSI 8S 320ps (EA888.4) 2021+ > Cupra Leon IV 300 TSI FW 2020+ > Cupra Leon IV 245 TSI FW 2020+ > Cupra Ateca 300ps (EA888.4) 2021+ > Cupra Formentor 310ps 2020+ > Cupra Formentor 245ps 2020+ > SEAT Tarraco 2.0 TSI 245ps 2021+ > Skoda Octavia IV vRS 2.0 TSI 245ps NX 2020+

Read more less

Product Description This is a replacement carbon canister including Pipercross filter that fits the FMINDGOLR twintake and Fiat FMINDF500 These have been created exclusively for Forge by filtration gurus Pipercross, and feature the latest multilayer-foam technology that is proving to be so successful in this season’s British Touring Car Championship  (BTCC). These are priced individually. Please order 2 when replacing carbon canister/filters on the FMINDGOLR system. *Please note - the Pipercross filter is excluded from the Forge lifetime warranty* The filter should be installed with a maximum clamp torque pressure of 3nm.Please watch our video on how to fit an air filter without damaging it.  

Read more less

Product Description *Please be aware that if your vehicle has the below MAF sensor on the inlet then this intake will not fit your vehicle, we currently do not offer an alternative for MAF vehicles* Forge are proud to present the latest high performance intake for the popular 1.5 TSI Evo engine found in a large selection of vehicles from the VW, Audi, Skoda, and Seat range. This kit features a Forge Ram Air high flow, pleated, synthetic nanofiber filtration filter, that has been manufactured for optimum size and fit to the available space giving superior flow and filtration with enhanced breathing for the 1.5 turbo charged engine. It also features a larger surface area than the stock filter and many competitors’ alternatives. The intake diameters on these air intakes have been carefully tuned to provide exactly the correct quantity of air ensuring solid consistent power gains throughout the rev range without any loss of low-end torque. The pipework is specifically designed to feed the turbo without interruption. The benefit of this is a gain of induction acoustics under acceleration, which improves the driving experience and adds a bit more drama to the TSI EVO engine. FITS: AudiA1A1 (GB) 2018-35 TFSI (1.5 TSI)A335 TFSI (1.5 TSI)Q235 TFSI (1.5 TSI)Q335 TFSI (1.5 TSI)CupraFormentor1.5 TSISeatArona1.5 TSIAteca1.5 TSIIbizaMk5 (KJ) 2017 - late 20211.5 TSILeonMk3 2012-20201.5 TSI 130/150 BHP 2018-Mk4 2022-1.5 TSITarraco1.5 TSISkodaKaroq1.5 TSIKodiaq1.5 TSIOctavia1.5 TSIScala1.5 TSISuperb1.5 TSIVolkswagenArteon(2017-2020)1.5 TSI(2020-)1.5 TSIGolfMK71.5 TSIMK7.51.5 TSIMK81.5 eTSI1.5 TSIPassat1.5 TSIT-CrossT-Cross 1.5 TSIT-Roc1.5TSITiguan1.5 TSITouran1.5 TSI Left hand drive intake Right hand drive intake As with all our intakes we design, high air flow is considered absolutely paramount, thus, we endeavoured to incorporate a large bore silicone high flow pipe with turbo inlet adaptor included. This helps to aid the engines performance and air flow in several ways. Designed in a similar way to a conventional velocity stack, it routes the air more directly into your turbo charger and allows more air than the stock inlet tract to be compressed due to its larger capacity. This can have a positive effect on accelerating your vehicle after long deceleration or between gear changes as more air is being kept within the intake system. The Forge developed inlet tract has more than a 50% increase in volume with the area at the mouth of the turbo increased to 46%. This, combined with no internal baffles or noise restrictors gives a helping hand to the vehicles acoustic notes and throttle response. With the use of Solidworks®, our CAD engineers have designed the heat shroud to fit round all the contours of the engine bay. This shroud combined with our specially formulated thermal coatings protects the intake from radiant heat while also guiding the cold air from the OE cold air ducting to the filter and housing. All of the billet components supplied have been made from 6082 Alloy and then anodised to ensure the alloy has no fatigue and stays without corrosion for years to come. This kit completed with stainless steel high quality hose clamps has the usual unrivaled performance you would expect from Forge Motorsport. Each Forge Motorsport intake hose is available in your choice of 3 colours to match the tastes and desired colour themes that you are looking for. Please select your colour choice when ordering. During testing we have achieved gains of up to 11bhp and 13lb/ft throughout the rev range from 2900 RPM. When installed in conjunction with an engine remap and free flowing exhaust the figure can be far greater as the OEM intake system is restricted on high performance engines. The FMINDK30 combined with either our atmospheric dump valve kit FMDV22 or our recirculating valve kit FMDV30 certainly transforms the whole driving experience and engine note of your 1.5 TSI EVO engine. As ever, this product comes with the Forge Motorsport lifetime warranty on all the hardware supplied, giving you the enthusiasts, the best product for your pride and joy.     The Forge silicone hoses in this kit have been designed to include an expensive inner liner of modified silicone known as Fluorosilicone. This means the hoses are suitable to be used with either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically The use of a Fluorosilicone liner ensures that Forge silicone hoses are the clear market leader. Lifetime warranty*    fits: AudiA1A1 (GB) 2018-35 TFSI (1.5 TSI)A335 TFSI (1.5 TSI)Q235 TFSI (1.5 TSI)Q335 TFSI (1.5 TSI)CupraFormentor1.5 TSISeatArona1.5 TSIAteca1.5 TSIIbizaMk5 (KJ) 2017 - late 20211.5 TSILeonMk3 2012-20201.5 TSI 130/150 BHP 2018-Mk4 2022-1.5 TSITarraco1.5 TSISkodaKaroq1.5 TSIKodiaq1.5 TSIOctavia1.5 TSIScala1.5 TSISuperb1.5 TSIVolkswagenArteon(2017-2020)1.5 TSI(2020-)1.5 TSIGolfMK71.5 TSIMK7.51.5 ETSI1.5 TSIMK81.5 eTSI1.5 TSIPassat1.5 TSIT-Roc1.5TSITiguan1.5 TSITouran1.5 TSI

Read more less

Racingline Filter Oil & Cleaning Kit The Racingline Oil and Cleaner Kit will help you keep your filter in peak condition at all times and ensure that the complex triple-layer foam continues to deliver its power and filtration benefits for many years. Instructions are provided for cleaning and maintenance. It’s a simple process, but please take time to read through, or ensure that your technician reads them, before you begin. We would suggest that you keep these notes with your car for future maintenance/owners. We recommend that the filter element is cleaned and reoiled every 10,000 miles/16,000 km, and/or a visual inspection at least every 12 months. This is a simple procedure, and will ensure that your filter continues to deliver the power improvements over a standard car. If your car is regularly used in a dry/dusty environment, we advise that you clean and re-oil your filter more regularly If you don’t clean your filter at the above intervals, no loss of filtration will occur, and your engine will still be fully protected. However, the performance advantages from the additional air flow of a clean filter will be lost. You will also shorten the life of the filter element. REPLACEMENT FILTER Like all the other filters on your car, it’s worth replacing the air filter element itself periodically. Rather than cleaning and re-oiling, lots of customers prefer to simply replace their filter element for what is a relatively low cost. We recommend replacement after 2 years for optimum performance. Of course, the filter will last for a longer period of time with correct maintenance and inspection for condition of foam as laid out below. BUY REPLACEMENT FILTER Applications Please note, this information is a combination of supplier provided compatibility data and our workshop expertise. While every effort has been made to ensure the accuracy of this information Racingline Shop/VAGManchester are not liable for abnormalities or inaccurate data. Customers are wholly responsible for checking fitment for their vehicle. SKU: VWR120000

Read more less

Filters are recommended to be cleaned every 5000Km with either compressed air or with this cleaning kit. Special Notes:WE CANNOT SHIP THIS ITEM OUTSIDE OF THE UK DUE TO LIMITATIONS ON SHIPPING LIQUID CHEMICALS AND AEROSOLS

Read more less

1.5 TSI High-FlowPanel Air Filter. Set your MQB & MQB 'evo' 1.5 TSI engine free by allowing it to breathe better and operate more efficiently What doesit do? Looking for a simple, warranty-friendly upgrade for your car? ​ Our High-Flow Panel Air Filters, available for all Volkswagen Group 'MQB' 1.5 TSI EA211 cars, replace the restrictive factory paper filters with an improved, high flow and reusable lifetime triple-layer Trifoam® filter. Put simply, it’s the best Panel Air Filter you can buy. OEM-standards of design, quality, materials and construction, hand-made in the UK. Fits like a factory part; lasts like a factory part. Allow your engine to breathe better and operate more efficiently – improve the engine’s airflow, and power and fuel economy gains will follow.  By removing the inevitable restrictions that the standard paper panel filter gives, our Panel Filter allows a small but worthwhile increase in airflow through to the turbo.   TRIFOAM® FILTER Our unique Trifoam® filter construction allows us to sandwich three different foams together for the perfect filtration and minimum restriction. HAND-MADE IN UK Each filter construction is hand-made in the UK for the reassurance of the highest quality together with exceptional dust-loading properties. EFFICIENCY GAINS The result?  More mid-range power and improved economy, without wrecking your warranty. Confirmed applications. VWR11G815 All VWG 1.5 TSI EA211 EVO engines, including: > VW Golf 8 1.5 TSI 2020+ > VW Golf 7 & 7.5 2013-2020 > VW Passat B8 2015+ > VW T-Roc 2017+ > VW Tiguan II 2016+ > VW Polo 6 AW 2017+ > VW T-Cross 2017+ > VW Touran 2018+ > Audi A1 2010-2018 > Audi A1 GB 2019+ > Audi A3 8Y 2020+ > Audi A3 8V 2013-2020 > Audi Q3 2019+ > Audi Q2 2017+ > SEAT Ibiza 6F 2017+ > SEAT Leon IV FW 2020+ > SEAT Leon III 5F 2015-2020 > SEAT Ateca 2016+ > SEAT Arona 2017+ > SEAT Toledo 2012+ > SEAT Tarraco 2018+ > Skoda Octavia IV NX 2020+ > Skoda Octavia III 5E 2014-2020 > Skoda Fabia IV 2021+ > Skoda Karoq 2017+ > Skoda Rapid 2017+ > Skoda Kamiq 2019+ > Skoda Scala 2019+ > Skoda Kodiaq 2018+

Read more less

Product Description Average gains of 5.5bhp Gains of 16bhp at peak and average of 10bhp from 4500rpm when coupled with FMTIA5/9 Average gain of 20NM of torque Prepreg 2x2 twill formed carbon fibre Dyno proven Great induction noise More responsive throttle Lifetime Warranty Compatible Vehicles: Audi A3 1.8/2.0 TSI 2015 Onwards S3 2.0 TSI (8V Chassis) 2.0TSI (8Y Chassis) Sportback 2.0TSI (8Y Chassis) TT Mk2 2.0 TTS Mk3 8S (2014-2021) Mk3 8S 316bhp (late 2022-) Cupra Ateca VZ1, VZ2, VZ3, VZN 2021- Formentor 2.0 TSI (245 BHP) 2.0 TSI (310 BHP) Leon VZ1, VZ2, VZ3 Seat Leon Mk3 2012-2020   Skoda Octavia VRS 2.0 TSI 2013 Onwards Octavia 4 RS Superb 280 4x4 DSG Volkswagen Arteon 2.0 TSI Golf MK7 1.8 TFSI GTI GTI Clubsport ED40 R MK7.5 GTI  R MK8 Clubsport 45 GTI GTI S R Passat 2.0 TSI (2015-2021) T-Roc 2.0 2018-2021 Tiguan 2.0 TSI 2017 Onwards R 2022 Onwards (Gen 4) With the release of the VW Golf MK8 R, the development team at Forge Motorsport knew that there would be a great opportunity to help the EA888 engine breathe easier and make more power. We were lucky to get one of the first MK8R’s to enter the UK and used this opportunity to put months of development and testing into this new induction kit. Our MK8 Golf R has been put through countless hours of track day work and hill climbs, alongside the usual daily and spirited driving. This kit has been designed from the ground up, using 3D Scanning, FEA Simulation data in SolidWorks CAD, 3D printed development, and numerous dyno sessions to truly unlock the power. Simulation testing played a large part in the design process to help maximise the airflow. This included a tear drop cavity around the bonnet release mechanism to ensure that the airflow stays fast and laminar on its way to the filter element. The 3D printed prototypes helped with comparing our simulation testing to real world driving conditions. This is a valuable comparison that is used in the top tiers of motorsport, now being brought to your vehicle. During the final prototypes testing we found that the Forge induction kit with stock turbo inlet produced gains on average of 5.5BHP. However, when paired with our Turbo Inlet Adaptor FMTIA5/9 this is where the stock EA888 engine saw impressive gains, increasing power up to 16BHP at 6500RPM with a significant average power increase from 4500RPM to the 6700RPM Rev limit of 10BHP, while the drivability and the punch from extra torque increases can be felt on the road as between 4000RPM to the rev limit an average gain of 20NM is achieved. It’s worth remembering that this is with a stock ECU and no tune, so we would expect to see mapped cars returning even greater yields of power. This induction kit runs the full width of the slam panel, incorporating an elegant lip which neatly slides under the slam panel to ensure that all the cold air from the front of the vehicle flows through into the inlet tract with no detriment from the engines heat. During testing we found this to make a significant increase to airflow and a reduction to inlet air temperatures (IAT’s). Temperature and volume of air supplied to your vehicles engine that is compressed by the turbo charger has a better effect on performance when cool as this is to provide the engine with more oxygen (denser air), thus improving the combustion in each cylinder. In addition, by regulating and reducing the air temperature, it also increases the reliability of the engine by keeping the AFRs (Air Fuel Ratios) in each cylinder at a safe level; which in turn, can increase an engines power due to the air being cooler. A bigger bang is then created within the cylinder (providing the correct amount of fuel is added) - this equates to an increase in BHP and torque. It’s worth noting that this induction kit offers a massive amount of air to the EA888 engine, which is a must for anyone looking to push the performance of their car when tuning to stage 1, stage 2, and beyond. Not only do you get the bhp performance benefits, but INDK40 also offers a greater sound from the engine; particularly when on boost, and our product testers have reported a more responsive throttle too. Careful consideration into the other platforms that share the same engine configurations had also been at the forefront of our development engineers’ minds. This needed various vehicles to be sourced to ensure a perfect fit for many of the VAG groups performance vehicles. You have only got to look at our compatibility list to realise how much research and development have gone into this extraordinary performance induction kit. FMINDK40 is part of our acclaimed Hi Flow range and will ensure that your vehicle is getting critical cold air. Not only is the Forge part a better option for performance, but the carbon fibre really helps to give the engine bay some character. The high-quality carbon fibre is prepreg 2x2 twill formed in an autoclave from billet tooling and finished with an anti UV gloss gel coat. The Forge Motorsport lifetime warranty on all hardware products shows the trust we have in the quality of our products while they are being enjoyed on your pride and joy. The kit comes complete with everything you need for installation, which can be carried out in around 1 hour, including a set of full colour instructions. For such an easy to fit product it truly does create some remarkable gains. You can find a replacement filter here. *Please note - the filter is excluded from the Forge lifetime warranty*

Read more less

Compatible for: Audi -A1  A1 25/30 1.0 TSI/TFSI 2022- (GB) -A3 1.0 TSI (2022-) -Q2 1.0 TSI (2022-) Seat -Arona 1.0 TSI (2022-) -Ateca 1.0 TSI (2022-) -Ibiza    Mk5 (KJ) 2017 - late 2021  1.0 TSI              Mk5 (KJ) 2021-  1.0 TSI -Leon Mk4 2022-  1.0 TSI Skoda -Fabia PJ 2022- 1.0 TSI -Kamiq  1.0 TSI (2022-) -Karoq 1.0 TSI (2022-) -Octavia 1.0 TSI (2022-) -Scala 1.0 TSI (2022-) Volkswagen -Golf MK8  1.0 TSI (2022-) -Polo 1.0 TSI (2022-) -T-Cross 1.0 TSI (2022-) -T-Roc 1.0 TSI (2022-) -Taigo 1.0 TSI (2022-)   FMINDK52 is the Forge Motorsport cold air induction system for the 2022 onwards 1.0 TSI engine found in a large selection of vehicles from the VW, Audi, Skoda, and Seat range. With the highly successful FMINDK30 and FMINDK39 induction kits for the previous generation 1.0 TSI VAG vehicles there has been a large demand for Forge Motorsport to develop an improved air intake system for the latest VAG power unit.  As with all manufacturers in recent times, the need to make smaller capacity engines more powerful with better efficiency has been their top priority. To achieve these goals, the OEM design engineers must maximise the space to its fullest, which in turn creates more of a challenge for the aftermarket manufacturers and tuners to improve what is already fitted to the vehicle. Nonetheless, this has not stopped us at Forge Motorsport! Even with plenty of expertise from past developments with the previous small capacity VAG engines, this new power unit needed an extensive amount of testing time to ensure we produced a product that provided genuine improvements over the standard air box.  The CAD designed, laser cut, and precision folded heat shield is designed to form a barrier between the air inlet tract and radiant heat from the engine. It also helps duct the cold air to the air filter, to preserve low intake temperatures, which in-turn creates more power. Finished in our black textured powder coating, this creates a product with an OEM look and quality. This kit is offered with our Forge high flow, pleated, synthetic nanofiber filtration filter, which has been manufactured for optimum size and fit to the available space giving superior flow and filtration with enhanced breathing for the 1.0 turbo charged engine.   Alternatively, there is our foam filter option available soon that has been exclusively manufactured by Pipercross. During dyno testing we tried several filter options and we found that neither filter excelled over the other with results being almost identical throughout the rev range. Both the filters offered can be oiled by the end user to prevent fine dust commonly found in hot climates from entering the inlet tract. Testing was completed using Performance Remap in Gloucester with their VTEC 4 wheel drive dynamometer. This was to ensure all our data has been achieved with results as accurately as possible by an independent tuner.  The dyno graph below shows torque gains at 2600RPM all the way to redline, with a gain of nearly 10NM from between 3000RPM and 3500RPM. This gain is very beneficial as it is consistently higher than stock from turbo spool up through to full boost, resulting in noticeably sharper acceleration and a more exhilarating experience for the driver, as typically this is where true power gains can be felt when behind the wheel.   The Forge Motorsport induction kit FMINDK52 includes all the necessary hardware and step by step installation instructions for any car enthusiast with basic garage tools to fit at home, in just a couple of hours!  

Read more less

This product CAN NOT be used in conjunction with FMTIA13 FMINLH26 is our replacement intake hose for the 2022- VAG 1.0 TSI engine. This is a direct replacement for the original plastic inlet hose. This is a simple fitment which replaces the entire restrictive rear factory plastic ‘bellows’ pipe between the airbox and the turbocharger inlet.  Constructed from reinforced high quality 5 ply silicone, this hose offers increased rigidity to prevent deformation from engine movement or heat cycles. This product is offered in two colours, gloss black or bright red, so this hose is not only functional but it also improves the aesthetics of the TSI engine bay. Audi -A1  A1 25/30 1.0 TSI/TFSI 2022- (GB) -A3 1.0 TSI (2022-) -Q2 1.0 TSI (2022-) Seat -Arona 1.0 TSI (2022-) -Ateca 1.0 TSI (2022-) -Ibiza    Mk5 (KJ) 2017 - late 2021  1.0 TSI              Mk5 (KJ) 2021-  1.0 TSI -Leon Mk4 2022-  1.0 TSI Skoda -Fabia PJ 2022- 1.0 TSI -Kamiq  1.0 TSI (2022-) -Karoq 1.0 TSI (2022-) -Octavia 1.0 TSI (2022-) -Scala 1.0 TSI (2022-) Volkswagen -Golf MK8  1.0 TSI (2022-) -Polo 1.0 TSI (2022-) -T-Cross 1.0 TSI (2022-) -T-Roc 1.0 TSI (2022-) -Taigo 1.0 TSI (2022-)   This product takes about 10 minutes to install and like all our silicone products, is covered by our lifetime warranty.

Read more less

  The APR Open PEX intake system is the best price/performance intake system on the market and has already been installed thousands of times in vehicles.The sound and performance of the engine were significantly increased and the restrictive area in the intake tract was eliminated. This made it possible to reduce the pressure loss and increase the efficiency of the turbocharger while doing the same work. This results in more power and torque while reducing load. The system uses a washable 7-inch and very high quality conical cotton filter that has a 4-inch connection.This was also necessary to reduce the standard pressure drop and maximize the airflow while also significantly increasing the sound aspect. The PEX material conducts heat very poorly, which also benefits the system and therefore ideally contributes to increasing performance.The PEX material still gives the engine compartment a touch of stock component, as far as you can say for an open air filter. The material also offers the advantage that almost any design can be realized. This made it possible to create an extremely complex and organic shape of the heat shield, which can effectively shield the hot air from below. Features: Improved intake noise Reduction of pressure loss Increases the efficiency of the turbocharger ore power and torque High quality cotton filter Airflow is maximized Made from PEX material FITS: Shop By Car/Volkswagen/Passat B8 Shop By Car/Volkswagen/Tiguan (Mk2) Shop By Car/Volkswagen/Arteon Shop By Car/Volkswagen/Golf Mk7 Shop By Car/Volkswagen/Golf Mk8 Shop By Car/Skoda/Octavia Mk3 (5E) Shop By Car/Skoda/Superb (3V 2015-) Shop By Car/Audi/A3 (8Y 2020-) Shop By Car/Audi/A3 (8V 12-20) Shop By Car/SEAT/CUPRA/Leon Mk3 (5F) Shop By Car/SEAT/CUPRA/Leon Mk4 Shop By Car/Skoda/Octavia Mk4  

Read more less

The VORTEX SERIES Intake for the Volkswagen Golf MK8 R is a high performance Air Induction system. Designed, developed and tested in-house over the past 18 months by Direnza’s team of highly skilled engineers. Every aspect of the kit has been designed from the ground up with quality & performance at its heart. Our brand new system offers an OEM fit & finish whilst providing significant power gains across the rpm range. Dyno proven gains of +10bhp & +8.8nm CFD-Optimised dual inlets designed to force more cold air into the turbo Fully enclosed Airbox to combat high engine bay temperatures 3.5” Aluminium Intake pipe, powder coated premium wrinkle black Air-tight, Proflex grommet that absorbs natural engine movement Triple layer reinforced silicone reducer Upgraded water & recirculation hoses Fitment 2.0 TSI MQB ‘EVO’ / EA888.4 engines VW Golf 8 R 2020+VW Golf 8 GTI 2020+VW Golf 8 GTI Clubsport 2020+ Air Induction - Pipe Bore (mm) 88.9 Air Induction - Clamps 2x 11-16mm, 2x 25-38mm, 3x 78-101mm Air Induction - Silicone (mm) 1x Recirculation Pipe, 1x Water pipe, 3.5"-80mm Reducer Air Induction - Fittings 2x Fir-Tree Clips, 2x Rubber Grommets Air Induction - Filter Bore (mm) 88.9 Air Induction - Brackets Sensor Re-location Bracket Air Induction - Other 1x Proflex Air Induction - Bolts 1x M6 Nylock Nut, 1x M6 Washer

Read more less