Performance - VW Golf MK7 (2012-2020)

Only The Driven know that the cooler the air, the more power produced. Revo Intercoolers drastically improve your vehicles ability to cool air compressed by the turbo. Increased volume and surface area, bar and plate cores with end tanks specifically designed to promote even airflow all play a part in lowering temperatures; without negatively affecting pressure. REVO AIR INTERCOOLER MQB 1.8/2.0 TSI EA888 GEN3 The Revo Intercooler utilises unique design features to lower intake air temperatures, minimise pressure drop and allow the engine to produce impressive power and torque with Revo Software. The unique end tank profile promotes internal laminar flow by decreasing turbulence and increasing airspeed into the bar and plate core. This enhances charge air cooling giving you access to more power throughout the rev range. The limitations of the stock intercooler were apparent throughout testing. The stock part consistently struggled to manage charge air temperatures, even under normal driving conditions. The Revo Intercooler has been designed to improve on every restrictive element of the stock cooler, enhancing cooling efficiency by lowering intake air temperatures by up to 36ºC vs. the MQB Golf R intercooler, allowing you to drive harder, for longer. KEY FEATURES Bar & Plate Core Design Fully Cast End Tanks OEM Fitment Up to 51% Increased Core Volume Over 36ºC Lower AIT INCREASED CORE VOLUME The Revo Intercooler was built around a simple principle; create a cooler that can keep up with your demand for power. Designed from the ground up, the Revo Intercooler has much larger core volume than the OEM part and offers perfect fitment, improving cooling by utilising the full volume of the stock location space as well as cold ambient air from the front of the vehicle. END TANK DESIGN The stock end tanks are inefficiently designed and create turbulent air in corners. These sections create a natural flow distribution but slow charge air and increase pressure drop. The Revo end tank geometry maintains the largest possible cross-sectional flow area to and from the core. Coupled with a cast interior surface finish, the Revo end tanks allow air to flow freely without obstructions from turbulent air pockets found in the OE intercooler. End tanks play an important part in maintaining pressure and work in harmony with the core to promote airflow, the Revo end tanks are designed to offer the optimal balance between both of these key features.   BAR AND PLATE CORE Designed with a bar and plate core to maximise the efficiency of heat transfer, the pressure drop is also controlled as the air meets less resistance compared to that of a tube and fin alternative. The Revo Intercooler also features carefully specified fin geometry to maximise cooling properties while minimising flow restriction. The ambient core side utilises louvred fins to slow ambient air flow which improves heat transfer, while the charge core side features an offset internal fin design to balance surface area and air resistance to minimise pressure drop.   SILICONE HOSES Supplied with stronger oil resistant silicone hoses, the Revo Intercooler can be installed using the stock pipework or recommended Revo Intercooler pipework. The internal diameter of each silicone is precisely matched to the outer diameter of the ribbed inlet and outlet connections along with a unique Flush Fit design, allowing a smooth transition between components.   BRACKETS To ensures precision fitment, Only Revo offers a CNC machined bracket system. Produced to a superior tolerance than that of a cast mounting system, this unique feature also ensures that the supporting brackets are strong and less prone to failure.   RESEARCH AND DEVELOPMENT All Revo products are designed in-house using the latest 3D printing technology, CAD and CFD software. Every product is rigorously tested utilising an in-house Hub dyno and Revo data acquisition software. The Revo intercooler minimises turbulence while maximising heat transfer, promoting cooler air temperatures and low-pressure drop. This helps retains power and torque throughout of the rev range as highlighted during controlled Dyno testing. The Revo Intercooler was tested in-house to compare the performance against that of the stock Intercooler. First tested on a vehicle running the OEM Intercooler with Revo Stage 2 software, a Revo air intake system and Milltek downpipe, the Revo Intercooler was then installed and tested in the same controlled environment to highlight the benefits of enhanced cooling. PERFORMANCE DATA Golf GTI with Revo Stage 2 Software, Golf R intercooler and Carbon Series Front Scoop Showing the last of five consecutive dyno runs, the efficiency of the Revo Intercooler over the OEM Golf R intercooler is highlighted. With max gains of +10 HP & +20NM Torque, along with increased performance throughout the entire rev range, the stock intercooler struggles to effectively function in comparison to the Revo Intercooler which remained consistent throughout, losing just 2% peak power over the 5 runs compared to 5% on the stock cooler. INLET TEMPERATURE This is a metric used to confirm that testing on the Revo MQB Intercooler. This is used to show that the air temperatures going into the intercooler were similar for each test, confirming that outlet temperatures shown in the following graphs are purely down to differences in intercooler design/construction. As can be seen, the inlet temperatures during testing were hotter on the Revo Intercooler, yet the Revo intercooler produced the lower outlet temps proving the cooling efficiency. OUTLET TEMPERETURE This graph illustrates the increased cooling performance of the Revo intercooler vs OEM Golf R intercooler over all five runs. The Revo Intercooler keeps temperatures below 49ºC on the fifth run, lower than the stock on its first at 58ºC.     FITMENT VEHICLE APPLICATIONS Manufacturer Model Engine Year Audi A3 8V 1.8 / 2.0TSI 2012 > Audi S3 8V 2.0TSI 2012 > Audi TT / TTS 2.0TSI 2015 > Seat Leon 1.8 / 2.0TSI 2013 > Skoda Octavia 1.8 / 2.0TSI 2013 > Skoda Superb 1.8 / 2.0TSI 2015 > VW Golf Mk7 / Alltrack / Sportwagen 1.8 / 2.0TSI 2013 > VW Golf Mk7 GTI / R 2.0TSI 2014 > VW Passat 1.8 / 2.0TSI 2015 > VW Tiguan 2.0TSI 2016 > VW Touran 2.0TSI 2016 > DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the Revo MQB Golf / Octavia / Leon Intercooler Instructions FITTING INSTRUCTIONS Download the Revo MQB A3 / S3 Intercooler Instructions NOTES Simple replacement of the OEM part Also available for the Golf Mk5/6 MLB Platform Will not fit on cars with O2 sensors fitted without interference on the sensor. It is recommended to speak with your dealer before if you are unsure.

Read more less

From many years of developing the race exhausts for the Racingline Performance Cup, we have partnered with our Championship Sponsors Milltek Sport to offer a more extreme ‘Cup Edition’ Exhaust System for the Golf 7 GTI available exclusively as part of the Racingline Performance range. Aside fromthe beautiful Titanium tailpipe trims, it’s built from the same high quality non-magnetic stainless steel as the race car systems, by the very same craftsmen, and in the exact same factory as every one of our racing cars. With minimal disruptions along its length, thesystem flows exceptionally,and isbased around a carefully optimised 3″íëí_í«Œ‚íëŒÇí«Œ (76mm) section tube for maximum power and torque gains with a refined throttle response throughout the rev range. We wanted a more extreme set up for the ‘Cup Edition’ exhaust, aimed at those looking for a slightly more purposeful soundtrack, thanks to its non-resonated centre section and smaller silencer box. Many customers have told us that they want the highest flow, least restrictive system available, and are happy with the louder volume that comes with a high-performance exhaust and the result is this. With Titanium tailpipe trims, discreetly etched with the R logo on the sides, not only does this exhaust deliver worthwhile performance gains, it offers a highly dynamic soundtrack that the enthusiast driver will love, and enhances the appearance of any Golf 7 Make no mistake, this is a sports exhaust, and has a rich and dynamic soundtrack to match. In development with Milltek Sport, we have deliberately taken the ‘Cup Edition’ system a step closer to that which we specify for our race cars. Through removing thetwo large silencer boxes thattheoriginal factory exhaust uses, and replacing with a single, smaller unit we have dramaticallyreduced the restrictions that the standard part causes. However, it is perfectly suitable for daily driving, with drone well contained at higher-speed cruising, only getting loud under full throttle acceleration. Enthusiasts will love it! Confirmed Fitment Please note, this information is a combination of supplier provided compatibility data and our workshop expertise, derived through experience or testing on EU manufactured vehicles unless stated. While every effort has been made to ensure the accuracy of this information we cannot be held liable for abnormalities or inaccurate data. For more information please see our Terms & Conditions under the legal section. MAKE MODEL VARIANT/ENGINE MAKE MODEL VARIANT/ENGINE Volkswagen Golf Mk7 2012-present

Read more less

REAR SIDE SPLITTERS VW GOLF MK7 R ESTATE fits : VW Golf mk7 R Estate version 2013 - 2016   COMPLETE SET CONTAINS:  SPLITTERS (LEFT + RIGHT)   Splitter is in black colour, it's ready for mounting.No need of any additional work, unless you want to paint it for a different colour.Splitter lowers the car visually and improves the grip and vehicle stability.Product is made of ABS plastic. ABS material was created specifically for use in the automotive industry.ABS is used in production of factory bumpers and other car body parts.ABS products are characterized with increased strength and flexibility.   This product has been TUV MATERIALGUTACHTEN certified (TUV certify for material).Please Note: Whilst most items are held in stock and we endeavour to have these with you in little time, there will be instances where this item will have to be manufactured to order and shipped directly from the factory in Poland. On these instances shipping can take between 3 and 5 weeks. By placing your order you are agreeing to the possible wait time, and cancellation due to inability to wait is not permitted and may incur an admin fee! If you wish to have the product "ASAP" please check stock levels prior to ordering via email to our support inbox

Read more less

Description  Now we give you the Chaser Edition Bluetooth footwell strip kit  This kit is for any car, simply tell us in the description what fuse type you have in your glove box fuse holder and we will send it out! with over 600 static colours, and 200 “Fluid” colour changing and dancing modes this really is a game changer  Controlled fully by your mobile phone using Bluetooth and our fantastic control app all the functions are controlled by you! Powered by your ignition the strip will come on as soon as you start your car and remain on until the ignition is switched off, The kit utilises your passenger footwell fuse box for power What’s in the Box? Footwell Strip Wiring Loom Bluetooth Control Module Instructions Warranty: The product is provided with a 12 Months guarantee as standard, Unless stated on the product packaging. If the packaging states more than 12 months, the product packaging must be kept to retain the extended warranty. Glove Box strip not included - This is for other Models - Images are catalogue images Vehicle Fitment: Some vehicles may use different types of bulbs depending on spec levels - For example, a special edition vehicle (Such as Ford "ST" or VW "GTi") may have a different light unit to a standard spec. If this item is listed on your vehicle catergory please confirm that it is the correct fitment for your vehicle by checking your item prior to ordering. The installation of LED's may trigger a Dashboard Error Message which is a harmless side effect of lower powered units, if this occurs for you please refer to our FAQ's. 

Read more less

Spoiler CAP V.1 VW Golf 7 R / R-Line / GTI FITS ONLY:VW Golf 7 R / R-Line / GTI (2013-2019) COMPLETE SET CONTAINS:-> Spoiler Extension + 3M Tape-> Degreasing Cloth-> Fitting Manual CHARACTERISTICS:-> Designed using 3D scanning technology to ensure a picture-perfect fit.-> Provides a unique OEM+ finish.-> Lightweight and offers some flexibility.-> This product is made from ABS plastic. The same material is used widely in the automotive industry.MORE INFORMATION:-> No additional work is required to finish the product.-> The product will arrive with a protective film.-> Removal of the protective film will void any returns, only remove once you are certain the product will fit.-> We cannot be held responsible for the incorrect installation or use of this product.-> Please compare the vehicle in the listing photos and title to your own, to ensure correct fitment.-> We advise trusting installation to a qualified professional unless you are confident following the provided

Read more less

BONNET VENTS UNIVERSAL Fits: UNIVERSAL PART BUT WE HAVE KNOWN TO FIT ON... Ford Focus 3 RS 2015 - up FORD Fiesta mk7 ST FACELIFT version 2013 -2016 Renault Megane 3 RS version 2010 - 2015 HONDA CIVIC IX TYPE R (FK2) 2015 - up OPEL CORSA D 2006 - and lots more   COMPLETE SET CONTAINS:-> Bonnet Vents GLOSS BLACKOnly one side of the bonnet extension is coated and the rear side is plain black.(Rear site and edge of item is not coated by structure) Please note, the majority of our products are made from ABS plastic, the flexibility of these products provides them the ability to withstand some pressure.We highly recommend installations are completed by a professional to ensure the product is fitted correctly and according to our fitting manuals.We can only accept a return within 14 days of delivery, if the product is in its original condition including protective film still on. A refund will be processed excluding shipping costs.All products arrive with a protective film, this is a very thin plastic vacuum sealed around the product to avoid the item sustaining any damage. Once removed you will notice the product does not have any scuffs or scratches.  Please Note: Whilst most items are held in stock and we endeavour to have these with you in little time, there will be instances where this item will have to be manufactured to order and shipped directly from the factory in Poland. On these instances shipping can take between 3 and 5 weeks. By placing your order you are agreeing to the possible wait time, and cancellation due to inability to wait is not permitted and may incur an admin fee! If you wish to have the product "ASAP" please check stock levels prior to ordering via email to our support inbox

Read more less

Rear Valance VW Golf R Mk7 (2013-2016) FITS ONLY:VW Golf R Mk7 (2013-2016)** The only rear side splitters that fit with the product are: VW-GO-7-R-RSD4 ** ** Our product is assembled as a replacement for the OEM rear valance ** COMPLETE SET CONTAINS: Rear Diffuser This product requires the removal of the original diffuser, self-tapping screws are needed to secure fitment of the new diffuser. Our full fitting manual can be found here: REAR DIFFUSER WITH CLIPS INSTALLATION MANUAL CHARACTERISTICS: Adds aesthetic value. Lightweight and offers some flexibility. This product is made from ABS plastic. The same material is used widely in the automotive industry. MORE INFORMATION: No additional work is required to finish the product. The product will arrive with a protective film.  Removal of the protective film will void any returns, only remove once you are certain the product will fit. We cannot be held responsible for the incorrect installation or use of this product. Please compare the vehicle in the listing photos and title to your own, to ensure correct fitment.  We advise trusting installation to a qualified professional unless you are confident following the provided fitting manual. This product has been TUV MATERIALGUTACHTEN certified. The removal of the holographic verification sticker will void a return, this identifies the item as an official and authentic Maxton Design product, removal is at buyer’s risk.   Please Note: Whilst most items are held in stock and we endeavour to have these with you in little time, there will be instances where this item will have to be manufactured to order and shipped directly from the factory in Poland. On these instances shipping can take between 3 and 5 weeks. By placing your order you are agreeing to the possible wait time, and cancellation due to inability to wait is not permitted and may incur an admin fee! If you wish to have the product "ASAP" please check stock levels prior to ordering via email to our support inbox

Read more less

RTS has developed the ultimate SMF conversion kit & flywheel specifically for the EA888 engine. RTS unique “Twin Friction” (drive plate) has been developed using a unique flywheel side friction material whilst adopting a segmented pressure plate face. The aramid friction exhibits 50% less wear than a conventional drive plate friction material.This material also reduces the effects of fade. Fade is the decline in the clutch system’s ability to transmit torque as operating temperatures increases. These features in combination with the previously mentioned micro-structure of spheroidal casting and ER2 technology allows the clutch kit to dissipate heat far more effectively, allowing the clutch to run cooler for longer. RTS kit has been designed with a higher clamp load enabling the clutch system to transmit 60% more torque over the standard clutch kit and is suitable for every day driving, fast road and track/circuit racing whilst maintaining user-friendly driving experience. RTS Twin Friction kit has been designed with a higher clamp load allowing. RTSHD-6006SMF (HD Organic) has been designed and manufactured to significantly exceed the original clutch system whilst also maintaining OE pedal effort, thus delivering a torque capacity of 405 lbs/ft of torque. RTSTF-6006SMF (Twin friction) has been designed and manufactured to significantly exceed the original clutch system whilst also maintaining OE pedal effort, thus delivering a torque capacity of 495 lbs/ft of torque.RTSPC-6006SMF (6 paddle) has been designed and manufactured to significantly exceed the original clutch system whilst also maintaining OE pedal effort, thus delivering a torque capacity of 550 lbs/ft of torque. Single Mass Flywheel RTS single mass flywheel offers a particularly suitable solution for vehicles where the original DMF is unable to dissipate heat effectively, but in addition, it offers greater longevity over DMF technology and is much more cost effective to replace.Technically, the SMF will reduce engine vibrations due to the increased inertia of the solid flywheel. In addition, the SMF is extremely durable, due to its efficient heat dissipation qualities and the lack of complex high wearing flywheel components Read more about our SMF kits here Suitable for the following EA888 Gen 3 Manual Cars Volkswagen Golf Mk7 R Volkswagen Golf Mk7 GTI Volkswagen Golf Mk8 GTI Audi S3 8V Audi TTS 8S Seat Leon Cupra MK3 (All variants) Skoda Octavia VRS Mk3

Read more less

TRIPLE QX Red (Concentrate) Antifreeze/Coolant 1Ltr Our High quality Red Antifreeze and Coolant has a powerful formula with 5 years protection for all seasons. It is suitable for any vehicle currently using Red antifreeze / coolant and meets GL12+ Standard. recommended by Car Mechanics Magazine who rated it on potency, heat capacity, versatility and value Performance LevelBS6580 (2010)VW G-12/TL-774D & VW G-12+/TL-774FMAN 278 & MAN 324MB 325.3Renault 41-01-00Protection: 50:50 mix - Up to -36c 33:67 mix - up to -20c TRIPLE QX Red (Concentrate) Antifreeze/Coolant 5Ltr Our High quality Red Antifreeze and Coolant has a powerful formula with 5 years protection for all seasons. It is suitable for any vehicle currently using Red antifreeze / coolant and meets GL12+ Standard, incorporating the latest in Organic Acid Technology (OAT). Recommended by Car Mechanics Magazine who rated it on potency, heat capacity, versatility and value. Performance LevelBS6580 (2010)VW G-12/TL-774D & VW G-12+/TL-774FMAN 278 & MAN 324MB 325.3Renault 41-01-00Protection: 50:50 mix - Up to -36c 33:67 mix - up to -20c TRIPLE QX Red (Concentrate) Antifreeze/Coolant 20Ltr Why not buy 20 litres to save you having to keep ordering more! 1 x 20litres of Red Concentrate Antifreeze/Coolant

Read more less

TRIPLE QX Blue Ready Mixed Antifreeze/Coolant 1Ltr Ready Mix Ethylene Glycol based Antifreeze with Winter Protection up to -36 C upon dilution Blue Ready Mixed Antifreeze/Coolant - 5ltr Suitable for all engine types including aluminium, and conforms to British Standards BS6580 (2010) and ASTM D 3306 & ASTM D 4985, SAE J 1034, AFNOR NF R 15601. It can be left in the system as a coolant and rust inhibitor for up to a maximum of 2 years in accordance with vehicle manufacturers requirements. TRIPLE QX Blue Ready Mixed Antifreeze/Coolant 5Ltr Ready Mix Ethylene Glycol based Antifreeze with Winter Protection up to -36 C upon dilution Blue Ready Mixed Antifreeze/Coolant - 5ltr Suitable for all engine types including aluminium, and conforms to British Standards BS6580 (2010) and ASTM D 3306 & ASTM D 4985, SAE J 1034, AFNOR NF R 15601. It can be left in the system as a coolant and rust inhibitor for up to a maximum of 2 years in accordance with vehicle manufacturers requirements.

Read more less

Buy with confidence from the largest UK and EU JR Wheels distributor! Model: JR14 Diameter: 17" Width: 8.5" Offset/ET: ET15 Colour: Machined Black PCD: Custom drilled to your specification. This wheel can accommodate any Centerbore up to 74.1. To ensure a perfect fit, Spigot Rings will be provided to match your car's Centrebore.Select your PCD stud pattern and offset using the drop-down boxes below.Custom wheels require slim style internal drive wheel nuts/bolts - we have plenty of these available in the wheel nuts & bolts section here. IMPORTANT: Check for shipping damage and test fit wheels before fitting tyres. We cannot rectify shipping damage or accept returns for wheels that have had tyres fitted JR Wheels are dispatched from the main EU warehouse, and will take a minimum of 3-5 days to ship regardless of shipping option chosen. As most of the JR Wheels are stocked in blanks, once a set of wheels is sent to be drilled the order can not be cancelled. Please ensure you check you have ordered the correct fitment and size before ordering, as once placed these can not be cancelled

Read more less

This is direct replacement for the intake hose and turbo inlet elbow on the 1.5 TSI (EA211 Evo) engines found in vehicles across the VAG range of vehicles. The replacement pipe & turbo adapter allow for increased airflow and removes the factory noise resonators unlocking some additional turbocharger intake noise. The kit currently only fits vehicles with engine codes starting with the letters DAC & DAD. Please compare your vehicle against the photos in the listing or lookup your vehicles engine code (normally located on a white sticker underneath the carpet on the boot/trunk floor. This part is the perfect companion to our Proram replacement panel filter (Search PPF-1878) or our upcoming open cone intake kit.

Read more less