All

If your after the most comprehensive silicone coolant hose kit available then this is for you. With a staggering thirteen hoses covered, which are made from the highest fabric re-inforced silicone, you just can't go wrong.These kits are available in Black and really look stunning. The Forge silicone hoses in this kit have been designed to include an expensive inner liner of modified silicone known as Fluorosilicone. This means the hoses are suitable to be used with  either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically The use of a Fluorosilicone liner ensures that Forge silicone hoses are the clear market leader. Lifetime warranty*   *T&C’s apply   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Here we have the Oil Cooler Manifold as seen in our Oil Cooler kit for the Audi RS4 4.2 (B7 2006-2008) - FMOCRS4  This Oil Cooler Manifold replaces the OEM part to allow the installation of an aftermarket oil cooler in place of the cooler that comes from the factory. Our Oil Cooler Manifold is machined from 6082 billet aluminium and then anodised black to prevent any possibility of corrosion. The manifold has two AN-12 fittings to allow you to add your own braided lines to suit your specific needs.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This kit has been designed to address the weakness of the stock oil cooler – the cooler fitted to your car from Audi is aluminium, but the fittings on the ends of the cooler hoses are steel. The result is corrosion between the two different metals which cracks the fittings over time, causing a slow oil leak that gets worse with age, and eventually ends in a catastrophic failure of the oil cooler lines - and if you are unlucky, the engine too. Due to the corrosion setting in on the lines, they usually cannot be removed from the oil cooler without damaging it. This results in the need for the oil cooler and both lines to be replaced at a cost of over £1100 from the dealer, before you factor in consumables and labour to change the parts. Our solution uses tried and test products. It is a full replacement right from the fitting on the engine block which is precision made from 6082 billet aluminium, and then anodised to prevent any possibility of corrosion. This fitting leads to -12 AN Hose Technik black anodised aluminium fittings on Hose Technik braided lines with black overbraid. Cooling is accomplished by a 19 row Setrab oil cooler, the same manufacturer that supplies Audi and several F1 teams, again with a black finish. All the mating parts are similar materials and are tried and tested in Motorsport - there is no fear of corrosion affecting the fittings after a few years of use. The cooler is supported on a laser cut and powder coated frame that also holds the Audi fan control module in place. With everything finished in black, it makes for the ultimate stealth installation and unless you know what you are looking for, you won’t see it. The original remit of this replacement was to do away with all the troublesome Audi parts, which this kit accomplishes, but by relocating the oil cooler slightly higher than stock, we have also reduced the chances of damage from road debris. All parts needed for installation are included - bolts, nuts, washers, brackets, and full instructions, though you will need up to additional 2 litres of engine oil to account for the loss from removing your old oil cooler, and for filling the new cooler and lines.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

The Forge Motorsport Turbo Blankets are designed to isolate the radiant heat produced by your turbocharger. This design has been created to withstand the harshest of environments and are designed to assist in the protection and prolonging of your engine components. Its unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. This product fits the T78, T88, and T6 turbochargers.   ·       Stainless Steel Rivets ·       Stainless Steel Fasteners ·       Carbon fabric Outer Shell ·       Calcium Magnesium Silicate Wool constructed Inner Core ·       High temperature silica fabric Interior Surface: ·       Max Temperature Rating: 2300°F/1260°C·       Continuous Use Limit: 1832°F1000°C Exterior Surface: ·       Direct Contact Limit: 1800°F/982°C·       Radiant Heat Limit: 2500°F/1371°C   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This Oil Cooler kit has been specifically designed to fit the VW T5.1 fitted with the twin turbo diesel engine (180hp). The kit includes a filter sandwich adaptor which incorporates a thermostat, so that the additional cooling only takes place when required. The kit also includes a 13 row oil cooler and braided oil hoses, mounting brackets, and everything else required. Please note: This product can only be installed in combination with our Intercooler FMINTVWT52 This kit is ideally suited to tuned vehicles or those that will experience extended periods of additional load e.g. when towing, or when operating in warm climates. The additional cooling will help improve engine longevity and may also ensure greater reliability.     Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

A set of silicone coolant hoses for the VW Golf MK7 GTi 2.0TSI engine.These hoses are Fluro-silicone lined to allow safe use with OAT type coolants.Available in Blue   The Forge silicone hoses in this kit have been designed to include an expensive inner liner of modified silicone known as Fluorosilicone. This means the hoses are suitable to be used with  either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically The use of a Fluorosilicone liner ensures that Forge silicone hoses are the clear market leader. Lifetime warranty*   *T&C’s apply   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

A set of 5 Silicone Coolant hoses for the MK5 2 Litre Golf. These hoses are sold as an additional set to our FMKC010 hose kit and are often referred to as the lower hose kit. Our coolant hoses, unlike other manufacturers inferior hoses, are lined with Flurosilicone to ensure they can withstand the coolants used in modern engines. Please select your colour choice in the options above when ordering.   The Forge silicone hoses in this kit have been designed to include an expensive inner liner of modified silicone known as Fluorosilicone. This means the hoses are suitable to be used with  either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically The use of a Fluorosilicone liner ensures that Forge silicone hoses are the clear market leader. Lifetime warranty* FITS: AudiA32.0 FSiTS32.0 FSiT (8P Chassis)SeatLeonMk2 2005-2012Cupra 2.0 TFSiVolkswagenGolfMK5ED30GTI *T&C’s apply   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   FITS MULTIPLE VEHICLES

Read more less

K03/K04 Forge Turbo Blanket - This blanket fits a multitude of applications - Please check the listing below The Forge turbo blanket is designed to isolate the radiant heat produced by your turbocharger. These turbo blankets have been extensively tested in the harshest environments, road race and track.  The Forge development team have designed this product to withstand the harshest of environments and to assist in the protection and prolonging of your engine components. Its unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket. FITS: AudiA31.6 TDI 2009-20131.8 TFSi2.0 FSiTA61.8T (B5,B6 Models)RS4(B5) V6S32.0 FSiT (8P Chassis)FordFocusST225SeatLeonMk2 2005-2012Cupra 2.0 TFSiVolkswagenEOSGolfMK5ED30GTIMK6ED35GTIRPassat2.0 FSiTTiguan 2.0 FSiT Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. Fitting the Forge turbo blanket will also prevent the associated engine components from getting heat soaked by the turbocharger. Aerospace quality Stainless Steel Rivets Stainless Steel Fasteners Carbon fabric Outer Shell Calcium Magnesium Silicate Wool constructed Inner Core High temperature silica fabric interior Surface: Max Temperature Rating: 2150°F Continuous Use Limit: 1850°F Exterior Surface: Direct Contact Limit: 850°F Radiant Heat Limit: 1250°F This Product Fits:  Audi 2008-2012 A3Audi 2008-2009 TTAudi 2009-2012 TT QuattroVolkswagen 2009-2012 CCVolkswagen 2009-2012 EOSVolkswagen 2008-2012 GTIVolkswagen 2008-2012 JettaVolkswagen 2006-2010 PassatVolkswagen 2009-2012 TiguanVolkswagen 2012-2014 Golf R   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised   FITS MULTIPLE VEHICLES

Read more less

The Forge Motorsport Turbo Blankets are designed to isolate the radiant heat produced by the turbocharger. Designed by the Forge development team on the Forge VW Golf MK1 Race car in the harshest of environments and exceeding all expectations, the Forge turbo blanket is designed to assist in the protection and prolonging the life of the engine components. ·       Stainless Steel Rivets·       Stainless Steel Fasteners·       Carbon fabric Outer Shell·       Calcium Magnesium Silicate Wool constructed Inner Core·       High temperature silica fabric The unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. This product also fits the vehicles with the following turbochargers: AudiA1A1 (8X) 2010-20181.4 TSI 2015 OnwardsA31.4 TSI/TFSI 2015 Onwards (8V)S32.0 TSI (8V Chassis)S4B9TTSMk3 8S 316bhp (late 2022-)CupraAteca(up to 2020)Formentor2.0 TSI (310 BHP)SeatIbizaMk4.5 (6P) 2015-20171.4 TSILeonMk3 2012-20201.4 TSI 125/140/150 BHP 2014-2019Cupra 280/290/300RSkodaSuperb280 4x4 DSGVolkswagenArteon(2017-2020)(2020-)GolfMK71.4 TSI 125BHP/138BHP/150BHPGTIGTI Clubsport ED40RMK7.51.4 TSI 138BHP/150BHPGTI RMK8RJettaMK6 (2010-2018)1.4 TSIMK7 (2018-2021)1.4 TSI2.0 GLIMK7.5 (2021-)2.0 GLIPoloGTI 2.0 2018-2020 AW ChassisT6T6 (2015-2019)2.0 TSITiguan2.0 TSI 2017 OnwardsR 2022 Onwards (Gen 4) Interior Surface: ·       Max Temperature Rating: 2300°F/1260°C·       Continuous Use Limit: 1832°F1000°C Exterior Surface: ·       Direct Contact Limit: 1800°F/982°C·       Radiant Heat Limit: 2500°F/1371°C   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

The oil filter housing on modern VAG engines does not allow for the previously common takeoff plates to fit under the filter and divert oil into an oil cooler mounted elsewhere on the vehicle. Instead they now use a oil to water cooling ‘block’ bolted to the front of the engine, and in many cases an undersize filter, or a paper drop in element, which prevents easy fitting of an oil cooler. As many people have found, if the vehicle is tuned, or if it is towing a heavy load, oil temperatures can rocket, with oil temperatures over 120°C (250°F) being easily achieved, which is close to the point that engine oil starts to break down. The Forge Motorsport FMOC2 replaces the oil to water cooling block, and although it still allows coolant to circulate, it more importantly gives two M22 takeoffs which, when fitted with the appropriate adaptor, allow fitment of oil cooler lines between an -6 and an -10 in size which can then be attached to an external oil cooler. Oil temperatures are stabilised, and engines can be worked harder for longer. To confirm fitment, please check the list of compatible vehilces below. This plate replaces the VAG OEM Part No. 03L 117 021 C. It fits ALL of the 2.0TDi and 1.6 TDi engines in the vehicles listed below. VW 2010-on Amarok, 2012-on Beetle, 2010-on Caddy, 2012-on CC, 2012-on Crafter, 2011-2016 Eos, 2012-on Golf Cabriolet, 2009-on Golf, 2009-2014 Golf Plus, 2011-on Jetta, 2011-on Passat, 2010-on Polo, 2009-on Scirocco, 2008-on Tiguan, 2011-on Touran, and 2010-on Transporter Audi 2011-on A1, 2009-2013 A3, 2008-on A4, 2012-on A5, 2011-on A6, 2012-on Q3, 2009-on Q5, and 2011-on TT Skoda 2011-on Fabia, 2009-on Octavia, 2012-on Rapid, 2011-on Roomster, 2008-on Superb, and 2010-on Yeti Seat 2011-on Alhambra, 2007-on Altea, 2009-on Exeo, 2009-on Ibiza, 2011-on Leon, and 2013-on Tolde   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   Fits Multiple Cars

Read more less

The Forge Motorsport Turbo Blankets are designed to isolate the radiant heat produced by your turbocharger. This design has been created to withstand the harshest of environments. The Forge turbo blanket is designed to assist in the protection and prolonging of your engine components and its unique design will assist in reducing turbo lag and produce cooler air intake temperatures, You will find that the Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. Stainless Steel Rivets Stainless Steel Fasteners Carbon fabric Outer Shell Calcium Magnesium Silicate Wool constructed Inner Core High temperature silica fabric   This product fits the Subaru models below: 2002 - 2005 Subaru Impreza WRX 2.0L 2006 - 2011 Subaru Impreza WRX 2.5L 2004 - 2011 Subaru Forester 2.5L 2005 - 2009 Subaru Legacy 2.5L   This product has also been fitted to a Subaru fitted with a VF43 turbo Interior Surface: ·       Max Temperature Rating: 2300°F/1260°C·       Continuous Use Limit: 1832°F1000°C Exterior Surface: ·       Direct Contact Limit: 1800°F/982°C·       Radiant Heat Limit: 2500°F/1371°C   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less