All

Compatible vehicles: Citroën -Xantia Daihatsu -All Makes Fiat -Uno Ford -Escort Toyota -MR2 Vauxhall -Cavalier   Suitable for most turbo cars with an Air Flow Meter.  Made from billet aluminium, this atmospheric diverter valve dumps the charge-air to atmosphere creating the "Whoosh" sound when the throttle is lifted. This increases both quicker throttle response and higher clamping load to maintain boost pressure more reliably. Unlike single piston or diaphragm diverter valves, this uses counter balanced springs and dual pistons to prevent the valve from leaking air into the intake system at idle. This prevents our diverter valves suffering any of the failures associated with single piston and diaphragm type diverter valves. All Forge Motorsport Dual-Piston Atmospheric Valves have been designed and built with the intent of venting 100% of the residual charge air remaining in your forced induction system to the atmosphere at throttle lift. While we have incorporated many elements into the design of the Dual-Piston valves to aid in their compatibility with mass air-flow sensor equipped vehicles, we cannot always guarantee that each individual’s application will be compatible with a valve that vents the charge air into the atmosphere. Forge Motorsport nor any of it’s Authorised Distributors can assume any responsibility for any adverse effects resulting from the installation of this valve onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of compensating for the loss of metered air through a vent-to-atmosphere valve such as this.   In The Box:1 x FMDV004 Valve1 x Forge Sticker If you wish to tune this product to fit the needs of your engine, please see the spring tuning kits below. The valve has a port size of 25mm We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner

Read more less

COMPATIBLE VEHICLES:Volkswagen - Golf - MK5 R32 Available in Black only A set of Silicone Coolant hoses for the R32 Mk5 Golf. Being modelled directly from the OEM hoses, these new precision engineered parts are an easy and direct replacement for the factory items, yet offer significantly greater ability to withstand much higher temperatures. Ideal on a standard car, but absolutely essential on a tuned, track or modified example! Allied to this, their superior woven fabric reinforcement and fluorosilicone internal lining, means that they will last an awful lot longer than the factory ever intended, too. Manual Gearbox cars only. The Forge silicone hoses in this kit have been designed to include an expensive inner liner of modified silicone known as Fluorosilicone. This means the hoses are suitable to be used with  either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically The use of a Fluorosilicone liner ensures that Forge silicone hoses are the clear market leader. Lifetime warranty* Please note that two of the hoses will not fit the DSG models  

Read more less

  Product DescriptionWhen looking to fit our carbon fibre induction kit FMINDK47 to a 2019 onwards VAG group vehicle that is powered by a DNWA 2019 onwards, you may find that the diverter valve hose to the DV elbow requires an adaptor. Earlier models utilise a straight silicone hose joiner, however these later models use a rectangular joiner. FMBH8 is designed to fit USDM and ROW vehicles that typically use this type of diverter valve hose, whereas European and UK spec vehicles tend to use a straight silicone hose. To identify which you need, please use the reference image below to help identify what variant you have.  If you have the same as the image on the left, you will require FMBH8 to enable fitting of the Forge Motorsport Intake FMINDK47   FMBH8 uses a 6082 billet Aluminium joiner fully CNC machined by our engineers at our Gloucester HQ in the UK which is then anodised for surface protection. Also supplied is our 4 ply silicone hose that not only improves the aesthetics of your engine bay, but is also of a higher quality than the OEM plastic hose.  As you can always expect from Forge Motorsport products, it’s a high quality fit and forget product. The Integrated water/methanol port or boost take off port is supplied with a blanking plug help to give further options for your build as you look to modify it further – much like the future proofing we included in the turbo inlet adaptors on our RS3 induction kit FMINDK47.   Although this product has been designed specifically for the Forge Motorsport carbon fibre induction kit FMINDK47 it can be used to run in conjunction with other aftermarket induction kits. All fitting hardware supplied (blanking plug thread size is 1/8th NPT)The hoses are suitable to be used with either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist.The construction of the hoses has been engineered to exceed that of the OEM fitments and will enhance any engine bay both technically and aesthetically.Stainless steel fasteners

Read more less

Developed, designed, and influenced from our direct involvement with BTCC and success with the Hyundai i30N, we are proud to release an oil cooling solution for the Hyundai Kona N. This oil cooler radiator is lifted straight from our motorsport department, so we know that this product performs well, and has been proven in several race events and winning vehicles over the past years. The cores are durable enough to last full race seasons and are perfect for fast road and track use. The cooler has now also been utilised in both of our other Hyundai oil cooling solutions and cleverly redesigned for a 100% plug and play solution for the Kona N. During our time developing world leading products for the Kona N, we found a significant flaw with the vehicle, especially when tuned, just as we did with the I30N. Oil temperatures can climb to dangerous levels when on track or when driven hard in hotter climates. Rising oil temperatures will result in only one outcome: a reduction of sufficient lubrication of your engines internal components, which, in due course, can potentially lead to engine damage. We saw oil temperatures reduce significantly during the development of this product when locating the oil cooler heat exchanger at the front of the vehicle’s radiator grill, this allowed for superior air flow. FMOC14 is a must-have product for the keen driver to protect their vehicles longevity, and perform safely and reliably. Unlike many oil cooler kits on the market, FMOC14 keeps the factory oil to water cooler in position - this essentially doubles your engines oil cooling. This product is not to be confused with a universal oil cooler, FMOC14 has a laser cut aluminium bracket which makes for perfect fitment to the Kona N. The kit is completely bespoke for this vehicle, with perfect length braided oil lines and our intelligent sandwich plate design making for a straightforward installation. The oil cooler is also designed to be mounted in the most efficient way possible as shown in the diagram below. This is to avoid oil cavitation which can also in some cases lead to potential engine damage over a long period of time. Manufactured in Gloucester, UK, FMOC14 is made to the uppermost standard and is backed up by the Forge Motorsport lifetime warranty. The kit comes with the following:1x Forge Aluminium sandwich plate1x Twin pass oil cooler 4x M6x20 fasteners4x M6 washers2x Oil lines 4x M6 Rubber Riv nuts1x M20x1.5 adaptor1x weather stripAll the fixings required and a comprehensive fitting guide

Read more less

Highlights: Increased performance (8bhp)Guaranteed for lifeComplete kit and instructions for ease of installationHand fabricated aluminium pipingAesthetically pleasing designPerfect with our inlet duct (FMINLD3)   fits:•    500•    595  - 145BHP  - Competizione 180BHP  - Trofeo 160BHP  -  Turismo 165BHP•    695  -  XSR Yamaha Limited Edition 165BHP  -  Rivale 180BHP The cold air feed is drawn in from the scuttle panel, this maximises the density charge of air entering the turbo intake. A perfect upgrade to compliment this is our Abarth specific inlet duct, FMINLD3. This combination of temperature and density gave us an 8bhp increase on our test cars as well as an incredible induction noise. It will put a smile on your face not only when you feel the power gains, but also when you open the bonnet and see this beautiful product sat in your engine bay. Our intakes/induction kits are a great and effective upgrade to your vehicle. This intake comes with a carbon fibre housing. To ensure we deliver the best quality products we can, and following the extensive design and development of our intake range, we enlist the services of one the world’s leading carbon fibre manufacturers, who’s products range from F1 aero, carbon fibre car bodies, and aircraft wings! Our intakes maximise the density charge of cold air for increased performance, as well as give a great sound, and enhance the aesthetics of your engine bay. When it comes to the filtration part of the intakes, there is no point creating such an efficient system for it then to be restricted by the OEM hose and filter. Therefore, for the filters, we engage one of our partners and experts in filtration control, Pipercross or RamAir! Additional parts such as aluminium piping are hand fabricated and polished, and the hoses are fluorosilicone for maximum longevity. This kit for the Fiat 500/595/695 comes with everything you need for the installation. It uses a high flow filter, available in either a foam (FMPK371) or pleated option (FMINDF500RCP). The aluminium components are skilfully hand fabricated in our UK headquarters. 

Read more less

Product Description Highlights: UV, temperature, and water-resistant Designed to locate in the OEM factory position Finished in high quality clear coat to ensure UV-protection and extra durability Take an already incredible vehicle, pop the bonnet and view the engine with no cover in place, yeah, its bit of an anti-climax. This is how many owners feel when showing off there EA888 Gen 4 engine as unfortunately the VAG group have recalled the engine covers due to a potential fire risk leaving the engine looking unfinished and disappointing, For those reasons, we took the OEM engine cover and improved it. Our cover fits on the original mounting locations, is water-resistant, and takes each heat cycle of the engine with ease. Not only that, it's finished in high quality clear coat to ensure UV-protection and extra durability.   Compatable Vehicles: Audi S3 2.0TSI (8Y Chassis) TT 45 TFSI (8S) TTS Mk3 8S 316bhp (late 2022-) Cupra Ateca VZ1, VZ2, VZ3, VZN 2021- Formentor 2.0 TSI (245 BHP) 2.0 TSI (310 BHP) Skoda Kodiaq RS 2021- Octavia 4 RS Volkswagen Arteon 2.0 TSI Golf MK8 Clubsport 45 GTI R T-Roc R (2022 Onwards) Tiguan R 2022 Onwards (Gen 4)   It fits perfectly with the Forge carbon intake and Forge turbo inlet pipe solution, which as a trio will completely transform your car engine bay! It is almost guaranteed that you will get some fingerprint marks/smudges on the engine cover during the installation, that's why we send our Forge engine cover in a microfibre bag. You can use the bag along with the Meguiar's Care Pouch to give your new car engine cover a fresh shine!  Manufactured by an autoclave process. This involves the use of up to 10BAR of pressure that is blown into a 100% billet mould to force the material out. This high amount of pressure ensures the carbon fibre is fully in contact with the surface of the mould, therefore, making sure the weave is tight, solid, and strong; this process will also ensure there are no imperfections in the product. In the Box:1 x Forge Carbon Engine Cover1 x Forge Micro Fibre Bag1 x Meguiar’s Care Pouch1 x Forge Decal   The Forge range of carbon fibre products are manufactured to the highest standards utilising the absolute best materials available. However, in certain applications and in areas of extreme temperature, this can lead to discolouration or fading (yellowing) of the carbon fibre. Unfortunately, due to this harsh and extreme environment, your Forge carbon fibre is not warrantied for that eventuality. All other aspects of your carbon fibre products are covered by our warranty process.

Read more less

When looking at the B58 engine within the M140i/240i/340i/440i engine bay it’s clear that BMW had left some room for modification within the inlet tract, the sound resonator and accordion ribs cause significant turbulence to the airflow causing a detriment to the engine’s potential performance. By removing these, and replacing it with five-ply silicone construction you gain a host of performance upgrades, including: Significant power gain of over 9bhp engine power and 7nm of torque. Improved induction noise. Multi ply silicone construction improves longevity of FMINLH25 over that of the OEM hose. 5 ply silicone construction will be able to handle strain of engine mapping far better than OEM hose. Fitting with no specialist tools in approximately half an hour.   Vehicle Fitment: BMW 1 Series F20/F21/F40 3/5 Dr Hatchback 2012 Onwards M140i 2016-2019 (B58) 2 Series F22/F23 2Dr Coupe/Convertible 2014 Onwards M240 2016-2021 (B58) 3 Series F30/F31 Saloon/Estate 2011-2019 340i 2015-2019 (B58) Testing was completed using Performance Remap in Gloucester with their VTEC 4 wheel drive dynamometer, This was to ensure all our data has been achieved with results as accurately as possible by an independent tuner. The results below speak for themselves, also with the added benefit of being a very easy component to fit with no specialist tools this is superb, affordable modification for the BMW enthusiast. From the dyno graph shown, performance gains can be expected from 4500RPM to the red line with +9BHP and +7NM of torque at peak RPM. Not only is FMINLH25 a functional improvement, but with it being available in black and red this product really helps to improve the aesthetics of the engine bay. One major difference of FMINLH25 is the diameter of the hose at the airbox end. Usually this is 85mm diameter, however FMINLH25 is 90mm diameter, and uses a silicone reducer sleeve so that it fits the OEM airbox correctly. This increase of 5mm diameter allows the inlet hose to be used with a wider variety of airbox/intake systems while also increasing the volume and de-restricting the flow of the OEM part,     This product is a direct fit for the OEM part 13718601682 (just the turbo inlet to airbox section). The hoses are suitable to be used with either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments and will enhance any engine bay both technically and aesthetically. Lifetime warranty. Why not pair this with our Forge Motorsport replacement high flow panel filter (FMPAN-0172) if you are using the OEM airbox.

Read more less

  Similar to many of the newer VAG engines, the latest 1.0 TSI power plant is not equipped with a diverter valve fitted as standard, Forge Motorsport has developed a twin piston dump valve that not only gives you a loud audible sound when lifting off the throttle, but also increases the throttle response during gear changes by reducing turbo lag. It has been designed to help the turbocharger maintain its rotational speed ready for when you accelerate, whilst also taking the strain away from the impeller. Without removing this stress from your turbo, it can lead to premature failure especially on remapped engines and modified vehicles.       This valve kit allows the fitment of our fast response blow off valve preventing turbo surge and prolonging the life of your engine’s turbocharger. The kit includes all the necessary hardware and step by step installation instructions for any car enthusiast with appropriate garage tools to fit at home, in just a couple of hours!  Due to the exposed position of the OEM boost pipe and the nature of heat cycle, the plastic that the OEM pipe is made from can deteriorate over time, becoming brittle and susceptible to boost leaks. This kit totally replaces this plastic pipe from turbo to manifold with a multi-ply silicone hose (available in a choice of red or black). Highlights: CNC machined billet couplers and components CNC machined twin piston Forge valve. Two hose options: red or black (Custom colours available but will incur a 50% non-refundable deposit and a lead time of 8-10 weeks) Forge Motorsports dump valve will not bring on any check engine lights (EML)  The hose has a quality inner lining of modified silicone known as 'Fluorosilicone'. This means that the hose will stay bright and vibrant and will not deteriorate over time. Forge Motorsport lined hoses are suitable to be used with modern long-life coolants, Organic Acid Technology coolants (O.A.T.) and oil mist. The construction of the hose has been engineered to exceed that of the OEM fitments, the Forge Motorsport hose will enhance any engine bay both technically and aesthetically. We cannot guarantee that this product will fit with all aftermarket intakes. Lifetime warranty We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner Audi-A1 A1 GB 25/30 1/0 TSI (2022-)-A3 1.0 TSI (2022-)-Q21.0 TSI (2022-) A1A1 (GB) 25/30 1.0 TSI (2022-) A31.0 TSI (2022-) Q21.0 TSI (2022-) Seat Arona 1.0 TSI (2022-) Ateca 1.0 TSI (2022-) Ibiza Mk5 (KJ) 2017 - late 2021 1.0 TSI Mk5 (KJ) 2021- 1.0 TSI Leon Mk4 2022- 1.0 TSI Skoda Fabia PJ 2022- 1.0 TSI Kamiq 1.0 TSI (2022-) Karoq 1.0 TSI (2022-) Octavia 1.0 TSI (2022-) Scala 1.0 TSI (2022-) Volkswagen Golf MK8 1.0 TSI (2022-) Polo 1.0 TSI (2022-) T-Cross 1.0 TSI (2022-) T-Roc 1.0 TSI (2022-) Taigo 1.0 TSI (2022-) This part will take approximately 1 hour to fit.  

Read more less

Forge Motorsport have a worldwide reputation of making industry leading parts for an array of performance vehicles; as such we’ve been able to work with some of most knowledgeable professionals in the tuning industry to produce the most versatile Audi RS3 performance intake on the market. 3D scans of left-hand drive (LHD) and right-hand drive (RHD) RS3 8Y’s and RS3 8V’s gave us 4 separate vehicle scans that we could then pull together into one file that has allowed us to create one intake that fits all 4 variations. So, no matter where you’re based in the world or whether you have an 8V or 8Y RS3, the Forge Motorsport FMINDK47 is the intake for you.   Trying to ensure that our performance intake is a one fit all solution also involved an understanding of how turbo inlets vary across the globe for the RS3 market. The OEM turbo elbow is an aluminium cast part with a 3” inlet tract that tapers down to the factory turbo charger cold side feed. Forge Motorsport offer and manufacture an upgraded silicone inlet elbow and turbo inlet adaptor (FMINLH9) not only to increase the area to the inlet tract but also the volumetric capacity. This has been increased to 3.5”and is the largest available product that fits RHD vehicles (due to space constraints with the brake master cylinder and is not physically possible to increase this size any further). However, this is not a problem on LHD vehicles, and as such there are various 4” variants available. To ensure our intake will work in conjunction with either the stock or any aftermarket inlet elbows on RHD or LHD vehicles we’ve incorporated an innovative solution that will be interchangeable if you wish to further enhance the engine performance of your Audi.  FMINDK47 incorporates and includes modular couplers so that it can fit any size turbo inlet you may choose to run. The machined end of the carbon intake where it meets the inlet tract to the elbow has a 4”(102mm) threaded billet attachment which tapers up to the huge 6” pleated filter on the intake side. At this billet alloy junction, it enables the end user to have interchangeable adaptors. Having this amount of adjustment with a vast increase in airflow allows this product to be suitable for stock or aftermarket turbo inlet solutions whether manufactured from silicone or aluminium. This enables the enthusiast to interchange the adaptors depending on if its currently stock or modified. FMINDK47 will support your RS3 to literally any state of tune.   Keeping inlet air temperatures (IAT’s) low is often a difficult part of developing induction systems, and several different variations were tested with FMINDK47. We decided on keeping the OEM air inlet to feed a specifically designed heat shield which sits flush up to the bonnet. An opening on the side opposite to the engine also helps with vehicles running stage 3+, as there is indirect airflow to this area and during testing a fully closed airbox caused restrictions.   Using carbon fibre brings obvious benefits of strength, weight, and aesthetics. However, a part that is often forgotten is its low thermal conductivity, which means it reduces heat soak and transmission of heat to nearby items. Replacing metal or plastic inlet solutions for FMINDK47 will help decrease IAT’s and increase the volume of air supplied to your vehicles engine that is compressed by the turbo charger. This has a better effect on performance when cool as this is to provide the engine with more oxygen (denser air), thus improving the combustion in each cylinder. In addition, by regulating and reducing the air temperature, it also increases the reliability of an engine by keeping the AFRs (air fuel ratios) in each cylinder at a safe level, which in turn, can increase an engines power due to the air being cooler. A bigger bang is then created within the cylinder, providing the correct amount of fuel is added. This can equate to an increase in BHP and torque.  We use SolidWorks CAD, 3D prints, and numerous dyno sessions to truly unlock the power. Simulation testing played a large part in the design process to help maximise the airflow. The 3D printed prototypes helped with comparing our simulation testing to real world driving conditions. This is a valuable comparison that is used in the top tiers of motorsport, now being brought to your vehicle. Being able to test 3 different 8Y RS3’s on 3 different independent dynos has been of vital importance to our development process. One of these RS3’s was (at the time of writing) the fastest 8Y RS3 in the world making 682Whp with FMINT33, FMINLH9, FMINDK47 installed along with a TTE777 Hybrid Turbo charger, this proves the FMINDK47 has great CFM airflow ratings over the standard intake system on vehicles with such a high state of tune.   The other vehicles tested were a UK RHD 8Y running FMINT33. We then changed out from the OEM turbo inlet to FMINLH9 to confirm the differences in BHP with these extra modifications. We were also able to test on a LHD 8Y that was completely stock.   With a completely stock tune vehicle we were able to see peak gains of 6BHP. However further analysis of the dyno graph shows that this peak BHP figure was produced 200RPM earlier (6097RPM instead of 6298RPM). Additionally, the power curves were smoothed across the entirety of the rev range, with gains seen across the board. To pull out some snapshots from the rev range as examples, at 3000RPM using just FMINDK47 saw an increase of 25BHP, and at 4500RPM there was an increase of 17BHP. Torque figures saw similar gains across the rev range, with a peak torque figure increasing by 17NM at around 100RPM earlier. When we analyse the dyno graph across the rev range, at 3000RPM using just FMINDK47 saw an increase in 55NM and at 4500RPM there was an increase of 23NM.   The gains lower in the rev range are truly impressive from a driver perspective this is where the benefits can be felt and is what typically puts you in your seat when the throttle is pressed. Vehicles with a stock tune, FMINLH9 and FMINT33 already installed hit a torque limiter earlier in the rev range with the addition of FMINDK47, which in turn can limit peak power results due to the engines ECU limiting power transmitted to the gearbox. So, if you have these three products installed, we highly recommend looking to tune your vehicle to really maximise the performance of the modifications installed. It’s worth remembering that this is with a stock ECU and no tune. We know from the independent testing we also completed on mapped cars (such as KSF’s) that the Forge Motorsport products create unparalleled performance.  It’s worth noting that this induction kit offers a massive amount of air to the EA855 EVO DAZA or DNWA engine, which is a must for anyone looking to push the performance of their RS3 when tuning to stage 1, stage 2, and beyond. Not only do you get the BHP performance benefits, but FMINDK47 also offers a greater induction noise from the engine; particularly when on boost, our product testers have reported a more responsive throttle which is to be expected from the impressive low down power gains the Forge intake provides.   FMINDK47 is part of our acclaimed Hi Flow range and will ensure that your vehicle is getting critical cold air. Manufacturing this product our of carbon fibre has ensured that we can give you the biggest RS3 induction kit on the market, with the largest possible volume for maximum smooth airflow. Not only is the Forge part a better option for performance, but the carbon fibre really helps to give the engine bay some character. The weave of the carbon has been optimised to match the carbon on the intake manifold, which really shows the level of detail we put into our designs. The high-quality carbon fibre is prepreg 2x2 twill formed in an autoclave from billet tooling and finished with an anti UV gloss gel coat. The Forge Motorsport lifetime warranty on all hardware products shows the trust we have in the quality of our products while they are being enjoyed on your pride and joy.  The kit comes complete with everything you need for installation, which can be carried out in around 1 hour, including a set of full colour instructions. For such an easy to fit product it truly does create some remarkable gains.  *Please note - the filter is excluded from the Forge lifetime warranty* 

Read more less

Product Description With Forge Motorsport leading the way in aftermarket products for the Hyundai N division vehicles, we are proud to present our Turbo Inlet Adaptor and Intake Tract for the Hyundai i20N. The kit is a full plug and play solution, with a replacement cast turbo inlet adaptor, CNC machined hose couplers, and a silicone high flow inlet hose. Available in a choice of Black, Red, and Performance Blue, the TIA11 will not only increase your Hyundai’s performance, but it also transforms the look and aesthetics of your vehicle’s engine bay.   The size of the inlet elbow has increased by over 170% to maximise the amount of air that can physically flow to the turbo from the inlet tract. The OEM factory alloy cast elbow is small, so we knew that this would be the key component to target as tuners start to increase the boost levels and performance output of the 1.6l turbocharged combustion engine. As well as this, the plastic OEM inlet hose has ribs and steps within the bore, causing detrimental turbulence while disturbing and slowing the airflow. By removing the ribs and steps, the larger Forge Motorsport silicone turbo inlet hose reduces the amount of turbulence over the standard item, enabling better airflow. Why do we use silicone? In the development process we tested an oversized aluminium pipe and found that it started to show signs of heat soak, this had a detriment to the impressive initial power gains. We also found after the third pull on the Dyno, the alloy pipe conducted too much heat on this application and started to decrease the gains. When using silicone, heat cannot be conducted as well, therefore even after six pulls, the silicone hose stayed at a steady temperature and did not decrease the power whatsoever. The inlet pipe fits directly to the factory airbox along with our FMINDK45 performance intake solution. The turbo inlet adaptor improves your vehicles airflow in several ways; designed in a similar way to a conventional velocity stack, it routes the air directly into your turbo charger and allows more air to be compressed due to its larger capacity, this has a positive effect when accelerating your vehicle after long deceleration, or in-between gear changes, due to more air being kept within the intake system. Dyno Results Testing was completed using Performance Remap in Gloucester with their VTEC 4-wheel drive dynamometer, this was to ensure all our data is achieved with results as accurately as possible by an independent tuner. As you can see from the dyno results below, peak power was increased from stock by nearly 7 BHP and 12NM of torque when mated to the OEM airbox and standard factory filter. The best news is that there are significant gains across the entire rev range, meaning that the car will pick up quicker and pull the whole way through to redline. TIA11 also benefits from a 17NM of power gain between 2500 RPM and 3000 rpm, this is right as the power comes in and can really change the feel and power delivery when behind the wheel. To compliment the turbo inlet, it can be matched to our induction kit FMINDK45. As you can see below this gave an increase of 12BHP and a torque increase of 20NM both at peak. These two products really do complement each other superbly both in conjunction, and as standalone modifications. After installing a tuning box, or re-calibrating the ECU with stage one or two tunes, the performance yields can be expected to be a lot higher than the figures stated. Testing on the dyno certainly represents the benefits from such a well-engineered product; this coupled with our Lifetime Warranty is just the reason to choose Forge for your Hyundai’s performance hardware.

Read more less

Developed from our direct involvement with BTCC and success with the previous generation I30N, Forge Motorsport is proud to release an oil cooler kit for the Hyundai i30N MK3.5. This oil cooler radiator is lifted straight from our motorsport department, so we know this component performs extremely well, as well as the cores tough and durable construction. Next stage was to design a kit incorporating this core which will fit the i30N Mk3.5 perfectly - the result is a bespoke oil cooler kit with true motorsport development behind it. During our time developing new products for the second generation i30N we found a significant floor with the vehicle especially when tuned. Oil temperatures can climb to dangerous levels when on track or when driven hard in hotter climates, The rising oil temperatures change the viscosity potentially thinning the oil, this will result in only one outcome, a reduction of sufficient lubrication of your engines internal components. Therefore, the FMOC13 is a must have product for the keen driver. The location of the oil cooler at the front of the vehicle’s radiator grill allows for superior air flow. During our development of this product, we have seen oil temperatures reduced significantly. Unlike many oil cooler kits, the FMOC13 keeps the factory oil to water cooler in position. This essentially doubles your engines oil cooling. This new product is not to be confused with a universal oil cooler. FMOC13 has a laser cut aluminium bracket which makes for perfect fitment to the i30N crash bar and has an incorporated side ducting which guides air flow through the core. Manufactured in Gloucester UK, FMOC13 is made to the uppermost standard and is backed up by the Forge Motorsport lifetime warranty. It is available in raw finish or black powder coat finish for the stealthier look. We’ve incorporated a thermostat that is built into the oil cooler sandwich plate, this has been set to open at 85C as this was observed to be the optimal working temperature of the oil cooler when testing, this means the engine is working at its most efficient oil temperature range however hard you push the vehicle.   The kit comes with the following: 1x Forge aluminium sandwich plate1x twin pass oil cooler 4x M6x20 fasteners4x M6 washers2x oil lines 4x M6 Rubber Riv nuts1X M20x1.5 adaptor1X weather stripAll the fixings required 

Read more less

Product Description High quality carbon fibre Coated with anti UV gloss gel coat Easy installation with full kit provided Located in OEM factory position Fits perfectly alongside Forge Motorsport induction Kit (FMINDF500) The OEM engine cover designed by Fiat has an incorporated factory airbox housed within the cover itself. This meant for many people, upgrading their induction kit would result in completely removing your engine cover. Now, with the release of our carbon fibre engine cover, FMEC4, Abarth owners can enjoy the power and performance of improved induction without having to sacrifice the aesthetic appearance of their engine bay! We designed our engine cover to fit perfectly alongside our induction kit FMINDF500, purposefully using carbon fibre as the material to compliment the carbon fibre canister of the induction kit. As this was specifically designed to fit alongside FMINDF500 we do not recommend, nor can we confirm fitment in conjunction with alterative aftermarket or OEM induction kits. 3D Scan, CAD, and Print 3D scans of an Abarth 595 with FMINDF500 installed were used to help develop this design. We used influence from the design of the original engine cover, so that FMEC4 will really compliment the aesthetics of the engine bay. Once the design was developed, we 3D printed a first prototype on our Formlabs Form 3L. The carbon fibre really helps to give the engine bay some character, blending in nicely with the carbon cannister of the Forge Motorsport induction kit. The high-quality carbon fibre is prepreg 2x2 twill formed in an autoclave from billet tooling and finished with an anti UV gloss gel coat. The Forge Motorsport lifetime warranty on all hardware products shows the trust we have in the quality of our products while they are being enjoyed on your pride and joy. The kit comes complete with everything you need for installation. Fitting can be carried out in around 1 hour and includes a set of full instructions. The Forge range of carbon fibre products are manufactured to the highest standards utilising the absolute best materials available. However, in certain applications and in areas of extreme temperature, this can lead to discolouration or fading (yellowing) of the carbon fibre. Unfortunately, due to this harsh and extreme environment, your Forge carbon fibre is not warrantied for that eventuality. All other aspects of your carbon fibre products are covered by our warranty process. 

Read more less

Fits Peugeot 308 GTI MK2 Proven to withstand temperatures up to 2500°F or 1370°C Prolongs the life of engine components Improves the appearance of the 308’s engine bay Stainless Steel Rivets and Fasteners Carbon fabric outer shell Calcium Magnesium Silicate Wool constructed Inner Core High temperature Silica fabric   The Forge Motorsport FMTUBL14 is a turbo blanket that has been specifically designed for the Peugeot 308 GTI MK2. This turbo blanket is designed to isolate the radiant heat produced by the turbocharger. The OE heat shield still allows a considerable amount of heat transfer thus creating a warmer engine compartment, which will have an effect on the engines components and increase intake temperatures. This design has been created to withstand the harshest of environments and proven to withstand temperatures up to 2500°F of radiant heat which will assist in protecting and prolonging the life of engine components. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path which helps reduce turbo lag and air intake temperatures resulting in more power. As a bonus the FMTUBL14 improves the appearance of the 308’s engine bay considerably, The OEM turbo heat shield tarnishes over many heat cycles, a problem which does not affect Forge Motorsport turbo blankets. All Forge Motorsport turbo blankets are designed and manufactured to the highest standards and use superior materials, unlike some turbo blankets which are constructed using substandard materials.

Read more less

The turbo muffler delete kit for the Hyundai I20N, this kit replaces the original restrictive compressor outlet with our smooth and turbulence free solution.  The OEM part is located on the outlet of the turbo compressor and its only function is to eliminate as much of the engines acoustics as possible. Where it does a good job of quietening down the audible sounds from the turbo it also disrupts the airflow in an area where it’s not needed.  With Forge Motorsports expertise in this area, we have developed a kit which has removed this baffled chamber in favour with our CNC machined billet adaptor which now creates a smooth transition and uninterrupted air flow track to the intercooler, this aids to increase airflow to the engine adding extra performance especially on tuned vehicles.  A new hose design has been made with an increased internal volume and a construction of fluorosilicone internal and iron oxide external which is designed to withstand extremely high temperatures and pressures, this is why Forge Motorsport gives this product its legendary LIFETIME warranty.    All of these improvements have now created an improved throttle response and an improved ambience due to the increased turbo acoustics.    Installation has been made straight forward with the inclusion of detailed step by step instructions.   The Forge silicone hoses in this kit have been designed to include an expensive inner liner of modified silicone known as Fluorosilicone with a high temperature external iron oxide engineered solution  The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically  CNC machined 6061 aircraft grade aluminium coupler  Improved turbo air flow  Increased audible sound from turbo  Direct replacement of OEM parts  Limited Lifetime warranty*  Complimentary Products Our uprated valve for the Hyundai i20N and the Elantra N Line has been expertly manufactured and designed in the UK, meaning we can provide the industry leading valve for your vehicle. Specifically designed for the Hyundai, this valve can be used either as a fully atmospheric (blow off) valve, or a recirculating valve! This billet aluminium oil cap will replace your OEM one, leaving your engine bay with a premium and high quality aesthetic. This cap is available in a choice of body colour (black or polished) and a choice of cap top insert (black or polished). This perfectly compliments your i20N!  A set of 4 ultra-high performance brake lines for the Hyundai i20N. These are a direct replacement/upgrade for the OEM brake line set and require no further modifications to fit.This brake hose will perform under the most extreme and harsh conditions, whilst still looking good and performing at the highest level.

Read more less

State of art polymer laminated glass cloth Superb heat barrier qualities Withstands radiant temperatures up to 450°C/850°F Ultra thin for minimal clearance As used in WRC and F1 Each roll is 50mm wide x 5 metres long (2" x 16ft) Adhesive backing for ease of fitting After extensive market research Forge Motorsport are proud to release a state of the art metalized polymer laminated glass cloth with adhesive backing that is both extremely light and capable of handling continuous radiant temperatures of up to 450°C. It reflects up to 80% of all radiant heat, whilst offering weight savings against other heat reflecting materials. Forge Motorsport's gold reflective heat barrier requires minimal clearance and is an extremely pliable material with a pressure sensitive adhesive backing that is easy to apply and remove. As used in WRC and F1, make no mistake this gold reflective heat barrier tape is of excellent quality and superb value for money. When used correctly this tape can be used to protect intake components thus lowering IATs resulting in a more efficient and reliable engine cycle. Typical uses are: Wrapping wiring, inside engine covers, bulkheads and firewalls, boost pipes, fuel lines, under seats, intake pipes, airboxes, engine compartments, fuel cells…  

Read more less

A replacement turbo actuator for the Maxda 2.3 found in the Mazdaspeed 3, 6, and the CX7. Using a range of available springs this actuator can be tuned to suit your requirements. Sold complete with mounting bracket. This product is built with a predetermined actuator spring suitable for at, or slightly above factory boost levels. The actuator can be assembled with a stiffer spring upon request. Please contact us directly concerning this process It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket. Forge Motorsport nor any of it’s authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Please contact us by email if you require more information   In The Box:1 x FMPACCX7 Actuator1 x Forge Sticker This actuator is built with a Green coded spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.  

Read more less

Adjustable Actuator for Subaru Impreza Fitted with IHI VF48 Turbo. Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMAC7SUB Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.

Read more less

Adjustable Actuator for Subaru Impreza 2006/07 WRX STi. Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMAC5SUB Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.

Read more less

The Forge Motorsport FMTUB11 has been designed for the Alfa Romeo MiTo QV. This turbo blanket is designed to isolate the radiant heat produced by the turbocharger. This design has been created to withstand the harshest of environments and proven to withstand temperatures up to 2500°F (1370°C) of radiant heat which will assist in protecting and prolonging the life of engine components.   Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path which helps reduce turbo lag and air intake temperatures resulting in more power.  

Read more less

Forge has developed this turbo outlet muffler delete pipe for the 2.0 petrol turbo (TSI) (EA888 GEN4 engine). This will not fit Golf R or Audi S3 8Y as this engine has no OEM turbo muffler. It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve throttle response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part.   On the new Golf GTI engine code DNP, this muffler delete gave an additional 8-10bhp during dyno tests. This will fit OEM part number 06Q145702B  

Read more less

FITS: AudiA31.8 TFSi2.0 FSiTTTMk2TTSMk2 8J (2009-2014)SeatAlteaLeonMk2 2005-2012SkodaOctaviaVRS 2.0 TSI 2013 OnwardsVolkswagenGolfMK6Scirocco 2.0 up to 2016 Product Description This will fit engine codes CAWA, CAWB, CBFA, CCTA, CCTB, CCZB, CCZA (With IHI RHF5 Turbo) Forge have developed this turbo outlet muffler delete pipe for the 2.0 TSI petrol turbo (EA888) engines fitted with the IHI turbo, specifically engine codes CBFA, CCZA, CCTA, and CCZB fitted to the Audi A3, Golf GTi (Mk6), Seat Leon and Skoda Octavia. It has been designed with 3 points of contact to eliminate any possibility of resonation.   This part will enhance the sound of the turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part. Complete with flouro lined hose and clamps.  

Read more less

A turbo actuator for the Corsa VXR and Astra 1.6 GTC. VauxhallAstraJ (2009-2016)2011-2014 (1.6T)CorsaD (2010-2015)2010-2015 (1.6T VXR) Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACCVXR Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

A turbo actuator for the Vauxhall Astra VXR (J Type). Vehicle fitment: Vauxhall Astra - J (2009-2016) Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACVXRJ Actuator1 x Forge Sticker This actuator is built with a green coded spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 3, 048 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

FITS: VauxhallAstraJ (2009-2016)2011-2015 (1.4T)CorsaD (2010-2015)2012-2015 (1.4T)E (2015 Onwards)(1.4T 2015 Onwards)Insignia2008-20142011-2014 (1.4T)Meriva2010-2017 (1.4T)Mokka2012-2017 (1.4T) Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACC14T Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.     Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less