Performance - Audi RS4 B7 (2004-2008)
forge Motorsport Audi RS4 (B7 Chassis) 4.2 Turbo Quattro Brake Lines
Fits: RS4 (B7 Chassis) 4.2 Turbo Quattro. Models: 2006-2008. 4 Line set. Why should I change my to Braided Stainless Steel ones? YOUR SAFETY! Better brake pedal feel – firmer under pressure More efficient braking- the PTFE lined, Stainless steel will not expand under load unlike OEM rubber hoses Long Lasting- PVC outer and Stainless-Steel end fittings will outlast the standard Mild Steel and rubber lines many times Available in many outer colour options to compliment your vehicle Rigorously tested and approved to the FMVSS 106 certification standards
£111.99
-
forge Motorsport Audi RS4 Oil Cooler Manifold (RS4 4.2 B7 2006-2008)
Here we have the Oil Cooler Manifold as seen in our Oil Cooler kit for the Audi RS4 4.2 (B7 2006-2008) - FMOCRS4 This Oil Cooler Manifold replaces the OEM part to allow the installation of an aftermarket oil cooler in place of the cooler that comes from the factory. Our Oil Cooler Manifold is machined from 6082 billet aluminium and then anodised black to prevent any possibility of corrosion. The manifold has two AN-12 fittings to allow you to add your own braided lines to suit your specific needs. Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.
£150.36
-
forge Motorsport Engine Oil Cooler for the Audi RS4 4.2 (B7 2006-2008)
This kit has been designed to address the weakness of the stock oil cooler – the cooler fitted to your car from Audi is aluminium, but the fittings on the ends of the cooler hoses are steel. The result is corrosion between the two different metals which cracks the fittings over time, causing a slow oil leak that gets worse with age, and eventually ends in a catastrophic failure of the oil cooler lines - and if you are unlucky, the engine too. Due to the corrosion setting in on the lines, they usually cannot be removed from the oil cooler without damaging it. This results in the need for the oil cooler and both lines to be replaced at a cost of over £1100 from the dealer, before you factor in consumables and labour to change the parts. Our solution uses tried and test products. It is a full replacement right from the fitting on the engine block which is precision made from 6082 billet aluminium, and then anodised to prevent any possibility of corrosion. This fitting leads to -12 AN Hose Technik black anodised aluminium fittings on Hose Technik braided lines with black overbraid. Cooling is accomplished by a 19 row Setrab oil cooler, the same manufacturer that supplies Audi and several F1 teams, again with a black finish. All the mating parts are similar materials and are tried and tested in Motorsport - there is no fear of corrosion affecting the fittings after a few years of use. The cooler is supported on a laser cut and powder coated frame that also holds the Audi fan control module in place. With everything finished in black, it makes for the ultimate stealth installation and unless you know what you are looking for, you won’t see it. The original remit of this replacement was to do away with all the troublesome Audi parts, which this kit accomplishes, but by relocating the oil cooler slightly higher than stock, we have also reduced the chances of damage from road debris. All parts needed for installation are included - bolts, nuts, washers, brackets, and full instructions, though you will need up to additional 2 litres of engine oil to account for the loss from removing your old oil cooler, and for filling the new cooler and lines. Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.
£1,081.59
