Performance - VW Golf MK5 (2003-2008)

State of art polymer laminated glass cloth Superb heat barrier qualities Withstands radiant temperatures up to 450°C/850°F Ultra thin for minimal clearance As used in WRC and F1 Each roll is 50mm wide x 5 metres long (2" x 16ft) Adhesive backing for ease of fitting After extensive market research Forge Motorsport are proud to release a state of the art metalized polymer laminated glass cloth with adhesive backing that is both extremely light and capable of handling continuous radiant temperatures of up to 450°C. It reflects up to 80% of all radiant heat, whilst offering weight savings against other heat reflecting materials. Forge Motorsport's gold reflective heat barrier requires minimal clearance and is an extremely pliable material with a pressure sensitive adhesive backing that is easy to apply and remove. As used in WRC and F1, make no mistake this gold reflective heat barrier tape is of excellent quality and superb value for money. When used correctly this tape can be used to protect intake components thus lowering IATs resulting in a more efficient and reliable engine cycle. Typical uses are: Wrapping wiring, inside engine covers, bulkheads and firewalls, boost pipes, fuel lines, under seats, intake pipes, airboxes, engine compartments, fuel cells…  

Read more less

This valve kit is for VAG vehicles equipped with the 1.4 TSI twincharged (supercharged and turbocharged) engines that have the electronically controlled bypass valves (2 bolt fitting). It is recommended for any vehicle where the boost pressure has been increased by an ECU software upgrade and for unmodified vehicles operating in warmer climates, as a solution to the many failures of the OEM valve, that have occurred. Our alternative is a fully engineered solution offering both significantly improved reliability. Our valve and installation kit replaces the original unit with a pressure/vacuum operated piston valve that still also retains the desirable OEM ECU control over valve actuation. This product has been thoroughly designed and tested with the expressed intent of offering improved valve response and maintaining ECU control while resulting in absolutely NO fault codes, NO check engine lights, and no adverse effects of any kind. All of the necessary components and detailed instructions are included and everything is designed to make installation as simple as possible.   In The Box:1 x FMDVRTSI Valve1 x Wiring Harness1 x Solenoid, Bracket, and Screws1 x Skoda Vacuum Tap2 x M5 x 35 Self Tapper Screw1 x Uprated Blue Spring10 x Cable Ties1 x 2000mm Length of 4mm Vac Hose1 x M5 x 12 Socket Button Screw1 x M5 Nyloc Nut1 x Instructions1 x Forge Keyring and Sticker   For Multiple Vehicles

Read more less

This actuator is compatable with the VAG 1.4 Twincharged engines found in the Audi A1, Seat Mk5 Ibiza / Bocenegra, Skoda Fabia and Volkswagen Polo. This product is built with a predetermined actuator spring suitable for at, or slightly above factory boost levels. The actuator can be assembled with a stiffer spring upon request. Please contact us directly concerning this process It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket. Please Note: The pressure figures listed in the drop down menu above are minimum regulated pressure figures. Forge Motorsport nor any of it’s authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. Please note some 1.4 TSI twin-charged 160 BHP models have an electronic OE actuator and this Forge Motorsport vacuum operated actuator is not a compatible replacement for the electronic type. The majority of models associated VAG models are fitted with the vacuum type but please check to ensure your engine has the vacuum type before ordering the Forge Motorsport product we offer.   In The Box:1 x FMACVAG07 Actuator1 x Forge Sticker   For Multiple Vehicles

Read more less

This valve kit is for VAG vehicles equipped with the 1.4 TSI twincharged (supercharged and turbocharged) engines that have the electronically controlled bypass valves (2 bolt fitting). It is recommended for any vehicle where the boost pressure has been increased by an ECU software upgrade and for unmodified vehicles operating in warmer climates, as a solution to the many failures of the OEM valve, that have occurred. Our alternative is a fully engineered solution offering both significantly improved reliability. Our valve and installation kit replaces the original unit with a pressure/vacuum operated piston valve that still also retains the desirable OEM ECU control over valve actuation. This product has been thoroughly designed and tested with the expressed intent of offering improved valve response and maintaining ECU control while resulting in absolutely NO fault codes, NO check engine lights, and no adverse effects of any kind. All of the necessary components and detailed instructions are included and everything is designed to make installation as simple as possible.   In The Box:1 x FMDVATSI Valve1 x Wiring Harness1 x Solenoid, Bracket, and Screws1 x 2000mm Length of 4mm Vac Hose1 x Vacuum Tap2 x M5 x 35 Self Tapper Screw1 x Uprated Blue Spring10 x Cable Ties1 x M5 x 12 Socket Button Screw1 x M5 Nyloc Nut1 x Instructions1 x Forge Keyring and Sticker

Read more less

This part replaces the stock white plastic filler, blue lid and plastic tube that leads to the main washer bottle in the inner wing, as they look a little out of place in the engine bay. The filler is replaces by an aluminium spun bottle with a Forge cap, and the tube is replaced with our own silicon hose. This product will fit: VW Scirocco, Golf Mk5 (2004+) Mk6 (2009+), Jetta, Touran, Caddy and Eos Seat Leon/Leon 4 (2006+), Altea (2004+) and Toledo (2005+) Skoda Octavia (2004+) and Superb (2008+) Audi A3/S3 (2004+) Fits Multiple Cars

Read more less

Please note: spacers are sold as PAIRS! if you want to do front and rear than qty x2 is needed!These CNC machined precision alloy wheel spacers are 8 mm thick with a dual 5 stud bolt pattern for both 100 and 112mm PCD fitments. The spacers are anodised black to inhibit corrosion and "bonding" to the wheel or hub. These spacers are suitable for most vehicles produced by Volkswagen Group. A 8mm spacer will give an overall track increase of 16mm when fitted to both sides of an axle. These spacers are priced and sold per pair. Extended wheel bolts are not suppliedPlease note, Due to the nature and complexity of a wheel spacer, customers MUST know that the size they are ordering is correct prior to ordering by measuring your stud length and wheel groove depth. Unfortunately, if over tightened the integrity of the spacer and / or bolts can be compromised - and due to this, any spacer that has been fitted, trial fitted or removed from its packaging can not be returned! Please be aware of this as by ordering you agree to this!

Read more less

This adaptor plate installs between the boost (MAP) sensor and mounting surface to allow a tapping to run a vacuum operated valve or for connection to a boost gauge.   In The Box:1 x Vacuum Tap2 x M6 x 35 Socket Cap Bolts2 x M5 x 35 Self Tapper Screws1 x Instructions1 x Forge Sticker FITS: AudiA1A1 (8X) 2010-2018A31.2 TSI upto 20141.8TA4DieselTTMk2DieselTTRSMk2 8J (2009-2014)SeatLeonMk2 2005-20121.2 TSI 2009-20121.4 Turbo 2007-2012SkodaOctaviaDieselVolkswagenAmarokEOSGolfMK51.4 S/Charge1.4 TurboDieselMK61.4 Turbo1.4 TwinchargedJettaMK5 (2005-2010)Polo1.4 TSI   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   Fits Multiple Vehicles

Read more less

Before fitment, please ensure the spacer fits flat to the back of the wheel. These wheel spacers are hubcentric These CNC machined precision alloy wheel spacers are 13 mm thick with a dual 5 stud bolt pattern for both 100 and 112mm PCD fitments. The spacers are anodised black to inhibit corrosion and "bonding" to the wheel or hub. These spacers are suitable for most vehicles produced by Volkswagen Group. A 13mm spacer will give an overall track increase of 26mm when fitted to both sides of an axle. These spacers are priced and sold per pair. Extended wheel bolts are not supplied.   In The Box:2 x FMWS13 13mm Wheel Spacer1 x Forge Sticker   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Rear replacement brake discs for Forge Motorsport brake kits. 330 x 28 Discs  Bolt Kit 2-piece floating rotors CNC machined lightweight forged billet aluminium rotor hats/bells Proprietary iron alloy rotor discs with directional curved vanes for optimized rotor cooling Slotted rotors for dust and gas evacuation adds long term durability Please Note:Forge Motorsport or its resellers will not offer any warranty or replacement if brake vibration, abnormal pad wear, caused by uneven discs which has resulted after poor and incorrect installation. Please Lock with 14NM ***THE MINIMUM THICKNESS OF THESE DISCS SHOULD BE NO LESS THAN 18mm BEFORE THEY ARE CHANGED***   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   Fits Multiple Vehicles

Read more less

Front Replacement Brake discs for Forge Motorsport Brake kits. 330 x 32 Discs  Bolt Kit 2-piece floating rotors CNC machined lightweight forged billet aluminium rotor hats/bells Proprietary iron alloy rotor discs with directional curved vanes for optimized rotor cooling Slotted rotors for dust and gas evacuation adds long term durability ***THE MINIMUM THICKNESS OF THESE DISCS SHOULD BE NO LESS THAN 29mm BEFORE THEY ARE CHANGED*** Please Lock with 14NM Please Note:Forge Motorsport or its resellers will not offer any warranty or replacement if brake vibration, abnormal pad wear, caused by uneven discs which has resulted after poor and incorrect installation.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   Fits Multiple Vehicles

Read more less

Front Replacement Brake discs and bolts Only for use with existing Bell Hats to fit Forge Motorsport Brake kits. 2x 356 x 32 Discs Bolt kit Proprietary iron alloy rotor discs with directional curved vanes for optimized rotor cooling Slotted rotors for dust and gas evacuation adds long term durability Please Note:Forge Motorsport or its resellers will not offer any warranty or replacement if brake vibration, abnormal pad wear, caused by uneven discs which has resulted after poor and incorrect installation. ***THE MINIMUM THICKNESS OF THESE DISCS SHOULD BE NO LESS THAN 29mm BEFORE THEY ARE CHANGED*** Please Lock with 14NM   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   Fits Multiple Vehicles

Read more less

Replacement Brake Pad set for 330mm and 356mm rear 4 pot caliper Forge Brake kit Yellowstuff Fastest Street, Trackday & Drift racing brake pads High friction formula improves brake effect 30-40%.Fastest brake pads for Street, Drift & Trackday racingZero brake fade makes this material perfect for fastest driving.Capable of repeated heavy brake use without brake “Fall-Off”.Very minimal disc/rotor damage characteristics.Suitable for shorter track events and race use.Medium hardness material feels good at pedal.If all you need is stopping power, this is the material choice.ECE R 90 type approved for most cars. Features red “brake in’ surface coating for instant safe braking after install.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Yet another first for the Volkswagen and Audi Tuning Market from Forge Motorsport! With the introduction of the VAG TSi Turbo Engine, we have developed a Patented Atmospheric Blow-Off adapter specifically designed to fit this application. Simple in execution, yet offering the desirable atmospheric blow-off valve sound, this product has been designed to be fully compatible with the Bosch engine management systems employed. This is not only a high quality replacement for vehicles fitted with the OEM solenoid valve part number 06F 145 710 D, but will fit earlier applications of the 2.0 FSiT, the later TFSi 2 litre, and the 5 cylinder TTRS..    In The Box:1 x FMDV14T Blow Off Adaptor3 x M6 x 40 Socket Cap Bolts1 x Forge Sticker If you are unsure if this product is suitable for your application, please contact us.  Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   Fits Multiple Vehicles AudiA31.4 Turbo1.8 TFSi2.0 FSiTA62.0TS32.0 FSiT (8P Chassis)TTMk22.0TTSMk2 8J (2009-2014)SeatLeonMk2 2005-20121.4 Turbo 2007-2012Cupra 2.0 TFSiSkodaOctavia2.0 FSiTVolkswagenBeetle2013 2.0EOSGolfMK51.4 TurboED30GTIMK61.4 TurboGTIRPassat2.0 FSiTSciroccoR 2.0 up to 2016T6T6 (2015-2019)2.0 TSI

Read more less

K03/K04 Forge Turbo Blanket - This blanket fits a multitude of applications - Please check the listing below The Forge turbo blanket is designed to isolate the radiant heat produced by your turbocharger. These turbo blankets have been extensively tested in the harshest environments, road race and track.  The Forge development team have designed this product to withstand the harshest of environments and to assist in the protection and prolonging of your engine components. Its unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket. FITS: AudiA31.6 TDI 2009-20131.8 TFSi2.0 FSiTA61.8T (B5,B6 Models)RS4(B5) V6S32.0 FSiT (8P Chassis)FordFocusST225SeatLeonMk2 2005-2012Cupra 2.0 TFSiVolkswagenEOSGolfMK5ED30GTIMK6ED35GTIRPassat2.0 FSiTTiguan 2.0 FSiT Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. Fitting the Forge turbo blanket will also prevent the associated engine components from getting heat soaked by the turbocharger. Aerospace quality Stainless Steel Rivets Stainless Steel Fasteners Carbon fabric Outer Shell Calcium Magnesium Silicate Wool constructed Inner Core High temperature silica fabric interior Surface: Max Temperature Rating: 2150°F Continuous Use Limit: 1850°F Exterior Surface: Direct Contact Limit: 850°F Radiant Heat Limit: 1250°F This Product Fits:  Audi 2008-2012 A3Audi 2008-2009 TTAudi 2009-2012 TT QuattroVolkswagen 2009-2012 CCVolkswagen 2009-2012 EOSVolkswagen 2008-2012 GTIVolkswagen 2008-2012 JettaVolkswagen 2006-2010 PassatVolkswagen 2009-2012 TiguanVolkswagen 2012-2014 Golf R   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised   FITS MULTIPLE VEHICLES

Read more less

Yet another first for the Volkswagen and Audi Tuning Market from Forge! With the introduction of the VAG 1.4 litre TSi Turbo/Supercharged Engine, we have developed an Atmospheric Blow-Off adapter specifically designed to fit this application. Simple in execution, yet offering the desirable atmospheric blow-off valve sound, this product has been designed to be fully compatible with complexities of this engine. Please choose from a black or silver adaptor using the options above.   In The Box:1 x FMDV14TSI Adaptor2 x M6 x 35 Socket Cap Bolts5 x M6 Washers1 x Forge Sticker   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   FITS: AudiA1A1 (8X) 2010-20181.4 TwinchargedA31.4 TwinchargedSkodaFabia5J 2007-20141.4 TSI VRSVolkswagenEOSGolfMK51.4 S/ChargeMK61.4 TwinchargedPolo 1.4 GTIScirocco1.4 Twincharged 160Tiguan1.4 TSI Mk1

Read more less

This pipe allows the removal of the Exhaust Gas Recirculation valve on the 1999-2005 VAG (transverse) 1.9 PD diesel engine with the following codes: ALH (90bhp), ATD (100bhp), AHF (110bhp), ASV (110bhp), AJM (115bhp) and AUY (115bhp). Incorporated onto the replacement pipe is a secured blanking plate and a boost gauge connection, which can be blanked off if not needed with a short length of pipe (supplied). Please note: All parts necessary for installation are included, however it is necesary to re-use the existing valve "O" ring seal with this pipe. FITS: AudiA3DieselA4DieselSeatAlteaIbizaMk2 (6K2) 1999-2002DieselMk3 (6L) 2002-2008DieselLeonMk2 2005-2012DieselSkodaFabia6Y 1999-2007VRSOctaviaDieselVolkswagenGolfMK4DieselMK5Diesel   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

A set of 5 Silicone Coolant hoses for the MK5 2 Litre Golf. These hoses are sold as an additional set to our FMKC010 hose kit and are often referred to as the lower hose kit. Our coolant hoses, unlike other manufacturers inferior hoses, are lined with Flurosilicone to ensure they can withstand the coolants used in modern engines. Please select your colour choice in the options above when ordering.   The Forge silicone hoses in this kit have been designed to include an expensive inner liner of modified silicone known as Fluorosilicone. This means the hoses are suitable to be used with  either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically The use of a Fluorosilicone liner ensures that Forge silicone hoses are the clear market leader. Lifetime warranty* FITS: AudiA32.0 FSiTS32.0 FSiT (8P Chassis)SeatLeonMk2 2005-2012Cupra 2.0 TFSiVolkswagenGolfMK5ED30GTI *T&C’s apply   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   FITS MULTIPLE VEHICLES

Read more less

This fits vehicles with a Charcoal Filter Installed. Excess crankcase pressure is vented from the crankcase through the PCV system, where it is drawn into the intake manifold and returned by the engine. This recirculated air contains aerated oil from the crankcase which is burned by the engine. Turbo charged engines often draw significant amounts of oil into the engine through the PCV system. This oil catch tank system removes aerated oil so that it can be drained and recycled. The kit is suitable for intallation to the 2 litre FSi engines such as in the VW MK5 Golf , MK5 Golf Edition 30 and SEAT Leon Cupra (not for engine codes CCTA CBFA).  FITS: AudiA32.0 FSiTS32.0 FSiT (8P Chassis)TTMk22.0SeatLeonMk2 2005-2012Cupra 2.0 TFSiVolkswagenGolfMK5ED30GTIMK6ED35RSciroccoR Depending on geographic location certain models listed in the compatible vehicles drop down menu are fitted with a charcoal filter to meet local emissions regulations. The filter is located at the front of the engine bay (on the left as you open the bonnet); also see black plastic canister in the engine bay image shown above. This kit with part number FMMK5CTC is for models fitted with the charcoal filter. If you do not have the charcoal filter as standard an alternative catch tank kit is available under the product code FMMK5CT. Please contact us by email or phone if you are unsure of which kit is compatible with your model.     Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Excess crankcase pressure is vented from the crankcase through the PCV system, where it is drawn into the intake manifold and returned by the engine. This recirculated air contains aerated oil from the crankcase which is burned by the engine. Turbo charged engines often draw significant amounts of oil into the engine through the PCV system.  This oil catch tank system removes aerated oil so that it can be drained and recycled. The kit is suitable for intallation to the 2 litre FSi engines such as in the VW MK5 Golf , MK5 Golf Edition 30 and SEAT Leon Cupra (not for engine codes CCTA CBFA). FITS: AudiA32.0 FSiTS32.0 FSiT (8P Chassis)TTMk22.0SeatLeonMk2 2005-2012Cupra 2.0 TFSiVolkswagenGolfMK5ED30GTI Depending on geographic location certain models listed in the compatible vehicles drop down menu are fitted with a charcoal filter to meet local emissions regulations. The filter is located at the front of the engine bay (on the left as you open the bonnet); also see black plastic canister in the engine bay image shown above. This kit with part number FMMK5CT is for models not fitted with the charcoal filter. If you do have the charcoal filter as standard an alternative catch tank kit is available under the product code FMMK5CTC. Please contact us by email or phone if you are unsure of which kit is compatible with your model.     Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

The stock PCV on the TFSI engine is quite fragile and over time, or when running lots of boost, the diaphragm inside can rip which can result in excessive blowby entering the inlet manifold at idle (smoking from the tailpipe) or a loss of boost when driving, which can cause other problems. Traditionally we fit a catch can to remove the PCV entirely and catch the oil vapours from the engine as seen here: FMMK5CTC and FMMK5CT. But if you want a cheaper and simpler solution, you can delete the PCV and divert the breathing to the rear cam cover outlet only, by using our Forge Motorsport PCV Delete kit. Simply put, it removes the PCV and links the two internal ports together which emulates what happens inside the stock PCV when the engine is on boost, but without any fragile components to break or split. This completely isolates the inlet manifold from the cam cover. FITS: AudiA32.0 FSiTS32.0 FSiT (8P Chassis)TTMk22.0TTSMk2 8J (2009-2014)SeatLeonMk2 2005-2012Cupra 2.0 TFSiSkodaOctavia2.0 FSiTVolkswagenGolfMK5ED30GTIMK6ED35RSciroccoR The kit also blanks off the port on the end of the inlet manifold that used to go to the PCV, and replaces it with our FMBGFK2 boost gauge fitting kit. This comes complete with 3 vacuum hose takeoffs and blanking screws so you can run a boost gauge, water spray controller, or you can blank them all off, it’s up to you. The kit comes complete will all parts necessary for installation and a full set of instructions. This product will fit the following vehicles: S3 (8P) 2.0 TFSI 265 PS (195 kW; 261 hp) BHZ/CDLA 2006–2013TT (8J) Mk2 2.0 TFSI 155 kW (211 PS; 208 bhp)  EA888   2010–TT (8J) Mk2 2.0 TFSI 155 kW (211 PS; 208 bhp)   2008–Leon Copa 2.0 TFSi 210 kW (286 PS; 282 bhp)  EA113  2008–Leon FR 2.0 TFSi 154 kW (209 PS; 207 bhp) CCZB/CAWB  2009–Scirocco Mk3 R 2.0 FSI 265 PS (195 kW; 261 hp) EA113)  2009–Golf Mk5 GTI 200bhpGolf Mk5 Edition30 Disclaimer: Any decision to install this product must rest solely with the purchaser as installation may adversely effect the manufacturers desired engine functionality or environmental pollution control measures. All responsibilities and liabilities remain with the customer and not Forge Motorsport.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Forge Motorsport has developed this turbo outlet muffler delete pipe for the 2.0 petrol turbo (TFSI)  (EA113 engine with K04 turbo). It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part. Complete with flourolined hose and clamps.  This product fits:K04 AudiS32.0 FSiT (8P Chassis)SeatLeonMk2 2005-2012Cupra K1VolkswagenGolfMK5ED30MK6RSciroccoR   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Replacement Filter on Spinning for FMIND5R32   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Product Description This is a replacement carbon canister including Pipercross filter that fits the FMINDGOLR twintake and Fiat FMINDF500 These have been created exclusively for Forge by filtration gurus Pipercross, and feature the latest multilayer-foam technology that is proving to be so successful in this season’s British Touring Car Championship  (BTCC). These are priced individually. Please order 2 when replacing carbon canister/filters on the FMINDGOLR system. *Please note - the Pipercross filter is excluded from the Forge lifetime warranty* The filter should be installed with a maximum clamp torque pressure of 3nm.Please watch our video on how to fit an air filter without damaging it.  

Read more less

Fits: Mk5/A5 type 1K chassis Models: 2006-2009 4 Line set. Stainless steel fittings used throughout (not plated mild steel). Why should I change my to Braided Stainless Steel ones? YOUR SAFETY! Better brake pedal feel – firmer under pressure More efficient braking- the PTFE lined, Stainless steel will not expand under load unlike OEM rubber hoses Long Lasting- PVC outer and Stainless-Steel end fittings will outlast the standard Mild Steel and rubber lines many times Available in many outer colour options to compliment your vehicle Rigorously tested and approved to the FMVSS 106 certification standards    

Read more less