All

A set of six coolant hoses for both the Hyundai i30n and Veloster N, which replace six of the OEM rubber hoses in the coolant system.  Forge designed these silicone hoses to withstand pressures that can be experienced on tuned and remapped engines. They will long outlast the original hoses and with our limited lifetime warranty on all Forge products, you can be sure these hoses won't let you down. Complete with all hose clamps required. Available in red, blue, or black - Please select your choice in the options above when ordering. We recommend you give yourself one hour to two hours to install all the hoses, remember that you will have to drain your coolant to fit these so make sure to have a tray to catch all the coolant.   TOUCHSHAREFULLSCREEN This interactive image was created with ThingLink.View this image on thinglink.com.     Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Designed by Forge to replace the original component on the Renault Megane 225/230 Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACMEG Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Working with in the limited space available surrounding the OEM side-mount chargecooler radiator and looking to develop the most efficient heat exchanger for the space available. Forge Motorsport has developed this compact V-mount radiator setup for the Mercedes A45 AMG (2.0L M133 Engine). Increasing the available core surface area by 43.5% over the OEM component. FITS: MercedesA Class W176 (2012-2018)A45AMG (2013-2015)CLA Class C117 (2013-2019)CLA45 (2013-2015)GLA Class X156 (2014-2019)GLA45 (Facelift 2015-) Featuring OEM style CNC machined couplers for direct fitment to the pre-existing chargecooler coolant pipework. No cutting of hoses or removal of couplers required. The laser cut radiator surround, clips into the OEM ducting and utilises the cold air feed from the front bumper. Refined design. This part has been carefully designed and developed using the latest Solidworks 3D CAD software. Researched, designed, developed, and handmade in Great Britain.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

The Forge turbo blankets are designed to isolate the radiant heat produced by the turbocharger. Designed by the Forge development team on the Forge VW Golf MK1 Race car in the harshest of environments and exceeding all expectations, the Forge turbo blanket is designed to assist in the protection and prolonging the life of the engine components. FITS: HondaCivicType R(FK2 2015-2017)(FK8 2017-2021) ·       Stainless Steel Rivets·       Stainless Steel Fasteners·       Carbon fabric Outer Shell·       Calcium Magnesium Silicate Wool constructed Inner Core·       High temperature silica fabric The unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power.  Interior Surface: ·       Max Temperature Rating: 2300°F/1260°C·       Continuous Use Limit: 1832°F1000°C Exterior Surface: ·       Direct Contact Limit: 1800°F/982°C·       Radiant Heat Limit: 2500°F/1371°C   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This pair of Forge turbo blankets are designed for the N54 and designed to isolate the radiant heat produced by the turbocharger. Designed by the Forge development team on the Forge VW Golf MK1 Race car in the harshest of environments and exceeding all expectations, the Forge turbo blanket is designed to assist in the protection and prolonging the life of the engine components. FITS: 1 SeriesE82 2Dr Coupe 2007-20131M 2011-2012 (N54)E88 2Dr Convertible 2007-2013135i 2007-2010 (N54)1M1ME82 2dr Coupe 2011-2012 (N54)3 SeriesE90/E91/E92/E93 Coupe/Convertible/Saloon/Estate 2004-2013335i 2006-2009 (N54) ·       Stainless Steel Rivets·       Stainless Steel Fasteners·       Carbon fabric Outer Shell·       Calcium Magnesium Silicate Wool constructed Inner Core·       High temperature silica fabric The unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power.  Interior Surface: ·       Max Temperature Rating: 2300°F/1260°C·       Continuous Use Limit: 1832°F1000°C Exterior Surface: ·       Direct Contact Limit: 1800°F/982°C·       Radiant Heat Limit: 2500°F/1371°C   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

The Forge Motorsport FMTUBL4 has been specifically designed for the Mini R56 stock turbo charger, and also fits the Peugeot 207/208 GTI. This turbo blanket is designed to isolate the radiant heat produced by the turbocharger. The stock Mini heat shield is inadequate and can result in warping the standard air scoop located in the bonnet. This design has been created to withstand the harshest of environments and proven to withstand temperatures up to 2500 °f of radiant heat which will assist in protecting and prolonging the life of engine components. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path which helps reduce turbo lag and air intake temperatures resulting in more power. Please note that a turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as this can cause damage to the blanket.   ·       Stainless Steel Rivets ·       Stainless Steel Fasteners ·       Carbon fabric outer shell ·       Calcium Magnesium Silicate Wool constructed Inner Core ·       High temperature Silica fabric   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

A set of three coolant hoses for the Suzuki Swift Sport 1.4 ZC33S, which replace three of the OEM rubber hoses in the coolant system. The kit consists of the upper radiator hose, lower radiator hose, and radiator overflow hose. Forge designed these silicone hoses so they can withstand pressures that can be experienced on tuned and remapped engines. They will long outlast the original hoses and with our limited lifetime warranty on all Forge products, you can be sure these hoses won't let you down. Available in red, blue, or black - Please select your choice in the options above when ordering. A complete High quality stainless steel hose clamp set for the above hoses are available from the drop down menu. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically Lifetime warranty*   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

The Forge Motorsport FMTUBL5 has been designed for the Fiat 500, 595, and 695 turbo (this will not fit those fitted with IHI turbo). This turbo blanket is designed to isolate the radiant heat produced by the turbocharger. FITS: Fiat500500Euro 6 Abarth595145BHPCompetizione 180BHPTrofeo 160BHP  Turismo 165BHP695XSR Yamaha Limited Edition 165BHP  Rivale 180BHPPuntoEvo 2010-2015Abarth Multiair This design has been created to withstand the harshest of environments and proven to withstand temperatures up to 2500°F (1370°C) of radiant heat which will assist in protecting and prolonging the life of engine components. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path which helps reduce turbo lag and air intake temperatures resulting in more power. Simple to fit using existing OEM hardware. Please note that a turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as this can cause damage to the blanket. ·       Stainless Steel Rivets·       Carbon fabric outer shell·       Calcium Magnesium Silicate Wool constructed Inner Core·       High temperature Silica fabric   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

If your after the most comprehensive silicone coolant hose kit available then this is for you. With a staggering thirteen hoses covered, which are made from the highest fabric re-inforced silicone, you just can't go wrong.These kits are available in Black and really look stunning. The Forge silicone hoses in this kit have been designed to include an expensive inner liner of modified silicone known as Fluorosilicone. This means the hoses are suitable to be used with  either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically The use of a Fluorosilicone liner ensures that Forge silicone hoses are the clear market leader. Lifetime warranty*   *T&C’s apply   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

The Forge Motorsport Turbo Blankets are designed to isolate the radiant heat produced by your turbocharger. This design has been created to withstand the harshest of environments and are designed to assist in the protection and prolonging of your engine components. Its unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. This product fits the T78, T88, and T6 turbochargers.   ·       Stainless Steel Rivets ·       Stainless Steel Fasteners ·       Carbon fabric Outer Shell ·       Calcium Magnesium Silicate Wool constructed Inner Core ·       High temperature silica fabric Interior Surface: ·       Max Temperature Rating: 2300°F/1260°C·       Continuous Use Limit: 1832°F1000°C Exterior Surface: ·       Direct Contact Limit: 1800°F/982°C·       Radiant Heat Limit: 2500°F/1371°C   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

K03/K04 Forge Turbo Blanket - This blanket fits a multitude of applications - Please check the listing below The Forge turbo blanket is designed to isolate the radiant heat produced by your turbocharger. These turbo blankets have been extensively tested in the harshest environments, road race and track.  The Forge development team have designed this product to withstand the harshest of environments and to assist in the protection and prolonging of your engine components. Its unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket. FITS: AudiA31.6 TDI 2009-20131.8 TFSi2.0 FSiTA61.8T (B5,B6 Models)RS4(B5) V6S32.0 FSiT (8P Chassis)FordFocusST225SeatLeonMk2 2005-2012Cupra 2.0 TFSiVolkswagenEOSGolfMK5ED30GTIMK6ED35GTIRPassat2.0 FSiTTiguan 2.0 FSiT Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. Fitting the Forge turbo blanket will also prevent the associated engine components from getting heat soaked by the turbocharger. Aerospace quality Stainless Steel Rivets Stainless Steel Fasteners Carbon fabric Outer Shell Calcium Magnesium Silicate Wool constructed Inner Core High temperature silica fabric interior Surface: Max Temperature Rating: 2150°F Continuous Use Limit: 1850°F Exterior Surface: Direct Contact Limit: 850°F Radiant Heat Limit: 1250°F This Product Fits:  Audi 2008-2012 A3Audi 2008-2009 TTAudi 2009-2012 TT QuattroVolkswagen 2009-2012 CCVolkswagen 2009-2012 EOSVolkswagen 2008-2012 GTIVolkswagen 2008-2012 JettaVolkswagen 2006-2010 PassatVolkswagen 2009-2012 TiguanVolkswagen 2012-2014 Golf R   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised   FITS MULTIPLE VEHICLES

Read more less

The Forge Motorsport Turbo Blankets are designed to isolate the radiant heat produced by the turbocharger. Designed by the Forge development team on the Forge VW Golf MK1 Race car in the harshest of environments and exceeding all expectations, the Forge turbo blanket is designed to assist in the protection and prolonging the life of the engine components. ·       Stainless Steel Rivets·       Stainless Steel Fasteners·       Carbon fabric Outer Shell·       Calcium Magnesium Silicate Wool constructed Inner Core·       High temperature silica fabric The unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. This product also fits the vehicles with the following turbochargers: AudiA1A1 (8X) 2010-20181.4 TSI 2015 OnwardsA31.4 TSI/TFSI 2015 Onwards (8V)S32.0 TSI (8V Chassis)S4B9TTSMk3 8S 316bhp (late 2022-)CupraAteca(up to 2020)Formentor2.0 TSI (310 BHP)SeatIbizaMk4.5 (6P) 2015-20171.4 TSILeonMk3 2012-20201.4 TSI 125/140/150 BHP 2014-2019Cupra 280/290/300RSkodaSuperb280 4x4 DSGVolkswagenArteon(2017-2020)(2020-)GolfMK71.4 TSI 125BHP/138BHP/150BHPGTIGTI Clubsport ED40RMK7.51.4 TSI 138BHP/150BHPGTI RMK8RJettaMK6 (2010-2018)1.4 TSIMK7 (2018-2021)1.4 TSI2.0 GLIMK7.5 (2021-)2.0 GLIPoloGTI 2.0 2018-2020 AW ChassisT6T6 (2015-2019)2.0 TSITiguan2.0 TSI 2017 OnwardsR 2022 Onwards (Gen 4) Interior Surface: ·       Max Temperature Rating: 2300°F/1260°C·       Continuous Use Limit: 1832°F1000°C Exterior Surface: ·       Direct Contact Limit: 1800°F/982°C·       Radiant Heat Limit: 2500°F/1371°C   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

The Forge Motorsport Turbo Blankets are designed to isolate the radiant heat produced by your turbocharger. This design has been created to withstand the harshest of environments. The Forge turbo blanket is designed to assist in the protection and prolonging of your engine components and its unique design will assist in reducing turbo lag and produce cooler air intake temperatures, You will find that the Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. Stainless Steel Rivets Stainless Steel Fasteners Carbon fabric Outer Shell Calcium Magnesium Silicate Wool constructed Inner Core High temperature silica fabric   This product fits the Subaru models below: 2002 - 2005 Subaru Impreza WRX 2.0L 2006 - 2011 Subaru Impreza WRX 2.5L 2004 - 2011 Subaru Forester 2.5L 2005 - 2009 Subaru Legacy 2.5L   This product has also been fitted to a Subaru fitted with a VF43 turbo Interior Surface: ·       Max Temperature Rating: 2300°F/1260°C·       Continuous Use Limit: 1832°F1000°C Exterior Surface: ·       Direct Contact Limit: 1800°F/982°C·       Radiant Heat Limit: 2500°F/1371°C   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

TECHNICAL DATA AIRTEC Motorsport header tank with sight glass for the Mini R56. Available in Motorsport Silver or Pro-Series Black. Comes with standard blue header tank cap.

Read more less

As part of our expanding Mini product range, AIRTEC Motorsport is proud to launch our header tank upgrade to suit R53 Cooper S models. A direct replacement for the original plastic tank, the AIRTEC Motorsport header tank is made from lightweight alloy and comes in a natural silver or high quality powder coated black finish. It also  features a sight glass to view the coolant level and comes with an uprated high pressure cap. The tank uses original fixing points, hoses and connectors so no drilling or cutting is required and fitting is a simple process. With an improved look to the engine bay and increased strength so the tank will not leak over time, this is a simple yet effective upgrade.  Please note: The Stant quick release high-pressure cap displayed in the images is for illustration purposes only, as Stant caps are no longer available. We now supply a replacement quick release high-pressure cap in a similar style. Features Direct replacement header tank for the R53 Cooper S Lightweight aluminium construction High quality black powder coat or natural silver finish Sight glass to view coolant level Uprated high pressure cap included No drilling or cutting required All fixtures included as well as fitting instructions Registered Design Right number: 6049901 AIRTEC part no: ATMSMINI2

Read more less

AIRTEC Motorsport header tank for Meglio (Megane powered Clio) This complete kit offers an easy, simple header tank upgrade solution for a Renault Megane turbo converted Clio. Fits Clio 197 without factory air-con fitted (or air-con delete kit fitted). Designed and tested in-house at AIRTEC HQ, tested at many UK track days & at the Nürburgring. A must have for a Megane engine swapped Clio 197. The kit features Pro Hoses silicone connectors, an uprated cap and custom made header tank that is stronger than the original item and offers better heat mangement in a direct replacement solution. Designed to locate on the left hand side of the engine bay and will fit with either our own uprated AIRTEC alloy radiator, or a stock Megane radiator. Supplied complete with all fixtures and fittings for an easy and professional installation. Finished in a choice of Pro-Series Black or Natural Silver. Gloss Black, Race Red, Performance Blue normally kept in stock. Other colour hoses, made to order Frozen White, Bright Yellow, Grey, Kawasaki Green, Orange, Purple, Vivid Pink, Nitrous Blue, Ultimate Green, Nitrous Blue Please allow 2-4 weeks for delivery.

Read more less

AIRTEC Motorsport header tank with sight glass for the Renault Clio 200 EDC Available in Motorsport Silver or Pro-Series Black. Comes with standard blue header tank cap. Registered Design Right number: 6059103

Read more less

Comes standard with new high pressure blue header tank cap! No Drilling required, uses original fixing points and is a direct replacement for the original plastic header tank. This is the ultimate water header tank. AIRTEC part no: ATMSHYU2 TECHNICAL DATA Hyundai I30N Lightweight Alloy Water Header Tank replacement. Easy fit takes 20 to 30 minutes to fit, Comes with a brand New High Pressure blue header tank cap No Drilling required, uses original fixing points and is a direct replacement for the original plastic header tank. Why not cover up that plastic cap with a Polished stainless steel cap cover, finished in satin Black and engraved Hot Logo, grooved inside for that perfect fit. Registered Design Right number: 6082522 AIRTEC part no: ATMSHYU2

Read more less

AIRTEC Motorsport lightweight alloy header tank for Fiesta MK7 – Complete with sight glass! No drilling required, uses original fixing points and is a direct replacement of the original Ford plastic header tank. Registered Design Right number: 6064605 AIRTEC part no: ATMSFO89

Read more less

Ford Fiesta ST Coolant Cap From VUDU Performance If you own a Ford Fiesta ST180 chances are the coolant cap has already failed and become stuck in the coolant bottle which is not only frustrating but can be detrimental when looking to fill the coolant bottle and realising you can no longer reseal it. The VUDU Performance Fiesta ST coolant filler cap is like no other completely replacing the Ford OEM coolant cap including the spring loaded assembly internally which is the inherently weak link in the chain. Further more the VUDU coolant cap is machined entirely from a T6061 Aerospace grade billet coupled with coolant and temperature resistant O-Rings to ensure ultimate reliability whilst aesthetically improving the look of your engine bay. It is important to note that this product comply's with the 21PSI regulated pressure found in the OEM coolant cap there for working seamlessly with the Ford Fiesta coolant system. The VUDU brand is renowned within the Ford tuning scene for its R&D through motorsport platforms, in house dyno facility and technical partners. This Fiesta Coolant cap has had the full VUDU treatment complying entirely to our strict testing regime whilst looking outstanding every time you look under the hood. VUDU Performance Coolant Cap Fitment: Mk7 Ford Fiesta ST Mk8 Ford Fiesta ST Mk3 Ford Focus ST Mk4 Ford Focus ST To add some more VUDU magic to that dull looking engine bay, take a look at the VUDU Performance Oil Cap! Key Feature List: Full Billet Aluminium construction including internal assembly Meets OEM recommended 21psi relief valve Internal assembly removes plastic OEM for total reliability Tested on our championship winning race car

Read more less

AIRTEC Motorsport Header Tank for Fiesta MK8 ST-200 AIRTEC Motorsport lightweight alloy header tank for Fiesta MK8 ST-200 & mk2 puma st complete with sight glass. No cutting or drilling required, uses original fixing points and is a direct replacement of the original Ford header tank. Registered design right number: AIRTEC part no:

Read more less

Here we give you the brand new wide mouth (or snorkel, as it can be known) for the MK3 focus - Facelift Models This is a straight fit with the removal of the bumper and is held on with 2 bolts! The snorkels are 3D Printed, and pressure tested prior to dispatch to ensure they are strong enough to handle all that is thrown at them! The snorkel is only available in black, However the mouth piece is available in a selection of colours! Technical Info: Max Flow - More speed = more air Prevents hot air being sucked in from the radiator Perfect finish and fit every time available in a multitude of colours Please Note: Whilst we will try and keep on top of stock we advise a 10-14 day delay on all orders, as if this needs to be made they take around 23 hours to print, then the testing to be carried out! Busy periods may be longer 

Read more less

NOW WITH OPTIONAL SIGHT GLASS! Focus Mk2 Lightweight Alloy Water Header Tank replacement. Easy fit takes 20 to 30 minutes to fit, Comes with a brand New High Pressure header tank cap No Drilling required (Unlike other Alloy tanks), uses original fixing points and is a direct replacement for the original Ford plastic header tank. Why not cover up that plastic cap with a Polished stainless steel cap cover, finished in satin Black and engraved Hot Logo, grooved inside for that perfect fit.

Read more less

Focus ST225 Group A Cold Air Feed which is designed to work with all Group A Open filters. Supplies a cold air feed directly into the Group A Filter Improving and maximising the airflow and performance. The cold air feed comes with Cold feed guide which sits just below the filter securing the trunking. Each kit comes with a 780mm piece of ducting, 1 base plate with attached ram pipe and all required bolts and fixings. PLEASE NOTE: Silver finish is for illustrative purposes only.

Read more less