forge Motorsport

This valve kit is an evolution of the FMARSDV dump valve we market for the 8P chassis RS3. It was developed for those who have tuned, or plan to tune, their 8S chassis Audi TTRS or 8V chassis Audi RS3 in excess of 450hp. Audi have seen fit to not change the design of the OEM dump valve from the previous RS3, so the same issues are carried over to the new 8V chassis, namely it was observed that cars over 450bhp were randomly getting errors from the stock solenoid dump valve not functioning. Whilst the stock valve will operate as designed, with the boost level necessary for 450bhp the stock valve couldn’t move the volume of air it needed to, so the ECU was seeing too great a positive boost in the MAP readings between gearchanges and assuming the stock valve wasn’t functioning correctly. We looked closely at this issue, and noted that there would be no real fix for this as the size of the hole for the valve is too small in the stock elbow. We decided that we would re-design and produce our own elbow, allowing a much larger DV port, which in turn would allow fitment of a larger valve to take advantage of it. We also improved the internal flow of the elbow and removed restriction within the valve. The elbow design has been changed by Audi to accommodate a different throttle body, so our design has changed too. *Please note this WILL NOT fit 2019 engine DNWA With the engine management on this engine being MAP based rather than MAF based, which is unlike many other Audi engines, we have also incorporated the option into the kit, of being able to run as a recirculation valve or with an atmospheric discharge/blow off.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Forge Motorsport present the Supercharger Reduction Pulley for the Audi S5 3.0T and replacement drive belt. Manufactured in house from stainless steel billet to exact tolerances 9% reduction from OEM pulley Tested and developed in conjunction with our Forge Asia office on their in-house dyno Unlike other manufacturers the Forge Pulley comes with our unparalleled LIFETIME WARRANTY. Supplied with genuine Audi replacement drive belt We recommend the use of any leading remapping companies that have engine management calibration software when installing this product. *Will not fit CRED and CREC engine, please see picture below for assistance.     In The Box:1 x Forge Pulley1 x Belt1 x Forge Keyring1 x Forge Sticker   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Forge Motorsport Turbo Actuator for the Borg Warner 06D 145 701J Turbo found in the Audi A4 2.0T (2005-2009) and A6 2.0T (2005-2011). For engine codes: BGB, BUL, BWE, BPG, BWT, BYK and BPJ Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACA4L Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This oil catch tank kit is the product of many months of intensive research and development by our in-house development team, and the end result is by far the most complete oil collection system currently on the market. Not only is it beautifully designed, it has been created to capture the maximum amount of harmful contaminants, including oil deposits, unused fuel vapours and moisture, all of which would ordinarily make their way back through to the inlet of the engine. Extensive testing has proven our oil catch tank kit's ability to effectively reduce sludge and carbon build up, in turn allowing the Tiguan 2.0 TSI engine to both breathe and perform more efficiently. It can therefore be viewed as a genuine performance enhancing product and one we recommend any owner seriously consider, particularly if they are planning more advanced power tuning at a later date. The 0.4l (400cc) catch tank boasts a slew of features intended to make it both easy to check and simple to drain, including a dipstick for level inspection and a well placed drain tap. The design of the kit has also been carefully considered, hence its inner tube which is constructed from anti-static smooth fuel resistant nitrile rubber. This is paired with an outer cover made from reinforced stainless steel wire braid (a Forge specialty), specifically a partial inner braid and a full cover outer braid. We developed this complex arrangement in order for the tank to be resistant to both pressure expansion and vacuum collapse, and also to enable the kit to function within a clearly defined temperature range – 54°C to +150°C (-65°F to 300°F) Finally, the kit features a pair of stainless steel reinforced oil resistant hoses with black external braiding, which combine with the supplied fittings to form an OEM-looking product when installed, so much so that the engine cover can still be clipped into place!   Highlights 0.4L capacity*A drain tap for ease of emptyingA dipstick for simple level inspection2 Quality stainless steel reinforced oil resistant hoses with black external braiding for that inconspicuous lookFully assembled with fittings to suit the OEM connectionsInner tube is constructed from anti-static smooth fuel resistant nitrile rubberOuter cover is constructed from reinforced Stainless Steel wire braid consisting of partial inner braid & full cover outer braiding which is resistant to pressure expansion and vacuum collapseTemperature Range: -54°C to +150°C (-65°F to 300°F)The engine cover can still be fitted after installationInstallation is straight forward with all necessary fittings and instructions included *Dipstick level is set at less than 0.4L for optimum breathing.     Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

The Forge Motorsport Turbo Blankets are designed to isolate the radiant heat produced by your turbocharger. This design has been created to withstand the harshest of environments and are designed to assist in the protection and prolonging of your engine components. Its unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. This product fits the T78, T88, and T6 turbochargers.   ·       Stainless Steel Rivets ·       Stainless Steel Fasteners ·       Carbon fabric Outer Shell ·       Calcium Magnesium Silicate Wool constructed Inner Core ·       High temperature silica fabric Interior Surface: ·       Max Temperature Rating: 2300°F/1260°C·       Continuous Use Limit: 1832°F1000°C Exterior Surface: ·       Direct Contact Limit: 1800°F/982°C·       Radiant Heat Limit: 2500°F/1371°C   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This Oil Cooler kit has been specifically designed to fit the VW T5.1 fitted with the twin turbo diesel engine (180hp). The kit includes a filter sandwich adaptor which incorporates a thermostat, so that the additional cooling only takes place when required. The kit also includes a 13 row oil cooler and braided oil hoses, mounting brackets, and everything else required. Please note: This product can only be installed in combination with our Intercooler FMINTVWT52 This kit is ideally suited to tuned vehicles or those that will experience extended periods of additional load e.g. when towing, or when operating in warm climates. The additional cooling will help improve engine longevity and may also ensure greater reliability.     Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Forge Motorsport EGR replacement kit. This kit is like no other for the T5 5 cylinder 2.5 diesel engine. It not only removes the restriction of the EGR valve but also fixes the common oil leak issue with the OEM hose and coupler. The Forge in house CNC machined EGR adapter, blanking cap and hose coupler complete with oil resistant hose addresses all issues providing the most comprehensive kit available. No cutting of original hoses required. The removal of the EGR valve, even those which are working perfectly, will give an increase in power, but most of the EGR valves after a period of time, compounded by those vehicles used on short journeys, will partially block and lead to power loss and poor running if they are not cleaned or replaced. This really is a worthwhile modification.  Please be aware the engine management light will come on and the glow plug light will flash, which will not effect  the way the vehicle drives. However you may wish to get the ECU remapped to overcome this.   If in the UK we have a trusted company who can do this for you. Pendle Performance Phone : 01282 851025Email : Sales@pendleperformance.comWeb : www.pendleperformance.com   PLEASE NOTE THIS WILL ONLY FIT TO ENGINE CODES AXD, AXE and BLJ Replaces VW EGR part number 070 128 070E   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This alloy replacement is CNC machined from a single billet to ensure a perfect fit without distortion or leakage and along with the supplied steel blanking plate, allows for the removal and replacement of the EGR valve on the T5 5 cylinder 2.5 engine.The removal of the EGR valve, even those which are working perfectly, will give an increase in power, but most of the EGR valves after a period of time, compounded by those vehicles used on short journeys, will partially block and lead to power loss and poor running if they are not cleaned or replaced. Please be aware the engine management light will come on and the glow plug light will flash. This really is a worthwhile modification. If in the UK we have a trusted company who can do this for you. Pendle Performance Phone : 01282 851025Email : Sales@pendleperformance.comWeb : www.pendleperformance.com   PLEASE NOTE THIS WILL ONLY FIT TO ENGINE CODES BNZ AND BPC    Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This valve has been specifically designed for the Audi A1 1.4 Turbo (122hp) engine. This is a full replacement atmospheric blow-off valve that integrates seamlessly with the OEM electronics and results in absolutely no fault codes, no check engine lights, and no detriment to the performance of the vehicle in any way. Like our many TSI replacement valve options, the valve is fully engineered to remedy the failure issues associated with the OEM solenoid valves. FITS: AudiA1A1 (8X) 2010-20181.4 TurboSeatLeonMk2 2005-20121.4 Turbo 2007-2012SkodaYeti1.4TS 122ps (2008-2012)VolkswagenScirocco1.4 Turbo 120 Please note this valve is only compatible with models that have a turbo mounted diverter valve as standard, as found in models up to and including most 2014 models. For recent 1.4 turbo models that do not have a standard turbo mounted diverter valve please see part number FMDV1.   Our valve uses full billet alloy construction with a piston based internal design that provides significantly improved reliability over the OEM valves, along with lightning fast response.   In The Box:1 x FMDVA1TSI Valve1 x Wiring Harness1 x Solenoid, Bracket, and Screws1 x 2000mm Length of 4mm Vac Hose1 x Skoda Vacuum Tap2 x M5 x 35 Self Tapper Screw1 x Uprated Blue Spring10 x Cable Ties1 x Instructions1 x Forge Keyring and Sticker If you wish to tune this product to fit the needs of your engine, please see the spring tuning kit below.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Forge has developed this turbo outlet muffler delete pipe for the 177hp 2.0 petrol turbo (TSI) It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part. This product fits:AudiA32.0 FSiTQ32.0 TSI (2011-2014)2.0 TSI (2015-2018)TTMk22.0SeatLeonMk2 2005-2012Cupra 2.0 TFSiSkodaKodiaq2.0L 2016-Octavia2.0 FSiT2.0L  VolkswagenBeetle2013 2.0EOSGolfMK6GTIPassat2.0 FSiTPoloGTI 2.0 2018-2020 AW ChassisScirocco 2.0 up to 2016Tiguan2.0 TSI 2017 Onwards 2.0 FSiT     To confirm compatibility, we have found that this will fit the vehicles that have a MAF sensor in the intake pipe as illustrated below. We recommend that you give yourself 2-3 hours to install this Forge Product   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Forge Motorsport Boost Tap Kit for 1.2 TSI Engines with code CBZA, CBZB or CBZC. This adaptor installs between the boost (MAP) sensor and the intake manifold. A simple solution for fitting a boost gauge or vacuum operated valve without having to cut into any original equipment.  Hardware including silicon hose and fitting instructions are supplied and the application is fully reversible. In the Box: Small Forge Sticker3.5mm Vac PortCable ties (x10)Cork gasket4mm Vacuum HoseInstructions QR Label FITS: AudiA1A1 (8X) 2010-20181.2 TSI 2010-20141.2 TSI 2015 OnwardsSeatIbizaMk4 (6J) 2008-20151.2 TSISkodaFabia5J 2007-20141.2 TSIVolkswagenPolo1.2 TSI upto 2014   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This actuator is designed for the Audi A4 and Volkswagon Passat 1.8T engines that are longitudinally mounted. ( crankshaft of the engine runs inline or the length of the chassis) Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACVAG02 Actuator1 x Forge Sticker This actuator is built with a green coded spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Following on from the success of our billet catch can kit for the Golf Mk5 and Golf Mk6, we are pleased to present another of our latest kits for the Golf Mk7R and Audi S3. If your engine bay looks like the image below, you will need to also purchase the washer bottle. This can be selected on the drop down menu above.  FITS: AudiS32.0 TSI (8V Chassis)VolkswagenGolfMK7GTIRMK7.5GTI RJettaMK7 (2018-2021)2.0 GLIMK7.5 (2021-)2.0 GLIPoloGTI 2.0 2018-2020 AW Chassis If your engine bay looks like the image below you do not need to purchase the washer bottle. In house testing has proven our oil catch can kit's ability to effectively reduce sludge and carbon build up, allowing the Golf Mk7R and Audi S3 engine to both breathe and perform more efficiently. It can therefore be viewed as a genuine performance enhancing product and one we recommend to any owner to seriously consider, particularly if they are planning more advanced power tuning later. The 0.4l (400cc) catch tank boasts a slew of features intended to make it both easy to check and simple to drain. Included is a dipstick for level inspection and a well-placed drain tap. Throughout the development of this product the design has been carefully considered, hence its inner tube which is constructed from anti-static smooth fuel resistant nitrile rubber. This is paired with an outer cover made from reinforced stainless-steel wire braid (a Forge specialty), specifically a partial inner braid and a full cover outer braid. We developed this complex arrangement for the tank to be resistant to both pressure expansion and vacuum collapse, and to enable the kit to function within a clearly defined temperature range -54°C to +150°C (-65°F to +300°F) The black external hose braiding and push fit fittings form an OEM-looking product when installed.   Highlights 0.4L capacity* A drain tap for ease of emptying A dipstick for simple level inspection 2 Quality stainless steel reinforced oil resistant hoses with black external braiding for that inconspicuous look Fully assembled with fittings to suit the OEM connections Inner tube is constructed from anti-static smooth fuel resistant nitrile rubber Outer cover is constructed from reinforced stainless-steel wire braid consisting of partial inner braid & full cover outer braiding which is resistant to pressure expansion and vacuum collapse Temperature Range: -54°C to +150°C (-65°F to 300°F) The engine cover does not need to be removed Installation is straight forward and all the necessary fittings and instructions included You will not need to modify any original equipment which means this kit is fully reversible.            *Dipstick level is set at less than 0.4L for optimum breathing.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

A set of silicone coolant hoses for the VW Golf MK7 GTi 2.0TSI engine.These hoses are Fluro-silicone lined to allow safe use with OAT type coolants.Available in Blue   The Forge silicone hoses in this kit have been designed to include an expensive inner liner of modified silicone known as Fluorosilicone. This means the hoses are suitable to be used with  either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically The use of a Fluorosilicone liner ensures that Forge silicone hoses are the clear market leader. Lifetime warranty*   *T&C’s apply   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

A silicone hose to replace the throttle body hose on the 2.0 litre Scirocco. Available in blue, black, or red.   The Forge silicone hoses in this kit have been designed to include an expensive inner liner of modified silicone known as Fluorosilicone. This means the hoses are suitable to be used with  either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically The use of a Fluorosilicone liner ensures that Forge silicone hoses are the clear market leader. Lifetime warranty* FITS: SkodaOctavia2.0 FSiTVolkswagenGolfMK6GTIScirocco 2.0 up to 2016   *T&C’s apply   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

A replacement turbo actuator for vehicles based on the MK6 Golf chassis with the 2.0 TSi engine, fitted with the IHI turbo. However, this unit will NOT work on IHI turbos that have the actuator welded to the turbine housing as well as the rod end permanently riveted to the flapper arm. This unit will only work on turbos that have the actuator bolted to the turbine housing and the removable arm. The OEM turbo/actuator will need to be inspected first to determine if this unit will work. Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACVAG08 Actuator1 x Forge Sticker This actuator is built with a green coded spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Forge Motorsport has developed this turbo outlet muffler delete pipe for the 1.8 and 2.0 petrol turbo (EA113 TFSI) engines fitted with the K03 turbo, specifically engine codes AXX and BWA as fitted to the Audi A3, Golf GTi (Mk5), Seat Leon and Skoda Octavia. This will not fit engine code CBFA CCZA CCTA CAWB and CCZB with IHI turbo It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will enhance the sound of the turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part. Complete with flourolined hose and clamps. This product fits:K03A31.8 TFSi2.0 FSiTA52.0 TFSITTMk22.0SkodaOctavia2.0 FSiTVolkswagenGolfMK5GTIMK6GTIScirocco 2.0 up to 2016       Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

A High Flow vacuum operated twin piston valve for the Audi S3 (8P model). Designed primarily to ensure that high volumes are discharged quickly, this valve can be configured as either a recirculation valve or a blow off valve. Everything required for the installation is supplied along with comprehensive instructions. We can offer the silicone hose in a choice of Red,Blue or Black, simply select your choice in the options above when ordering.   In The Box:1 x FMDV8PS3 Valve1 x Wiring Harness1 x Solenoid, Bracket, and Screws1 x PCV Adaptor Kit1 x 1000mm of 4mm Vacuum Tube2 x 45mm Hose Clamps2 x 35mm Hose Clamps1 x 25mm Blanking Plug1 x 25mm Side Pipe1 x Straight Silicon Hose (25mm x 65mm)1 x Silicon Hose #11876 x Cable Ties2 x M5 x 35 Self Tapper Screws1 x FMBGFK3 (Vacuum Tap, Gasket, and Bolts)1 x Instructions1 x Forge Sticker   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Forge Motorsport has developed this turbo outlet muffler delete pipe for the 2.0 petrol turbo (TFSI)  (EA113 engine with K04 turbo). It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part. Complete with flourolined hose and clamps.  This product fits:K04 AudiS32.0 FSiT (8P Chassis)SeatLeonMk2 2005-2012Cupra K1VolkswagenGolfMK5ED30MK6RSciroccoR   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

The stock PCV on the TFSI engine is quite fragile and over time, or when running lots of boost, the diaphragm inside can rip which can result in excessive blowby entering the inlet manifold at idle (smoking from the tailpipe) or a loss of boost when driving, which can cause other problems. Traditionally we fit a catch can to remove the PCV entirely and catch the oil vapours from the engine as seen here: FMMK5CTC and FMMK5CT. But if you want a cheaper and simpler solution, you can delete the PCV and divert the breathing to the rear cam cover outlet only, by using our Forge Motorsport PCV Delete kit. Simply put, it removes the PCV and links the two internal ports together which emulates what happens inside the stock PCV when the engine is on boost, but without any fragile components to break or split. This completely isolates the inlet manifold from the cam cover. FITS: AudiA32.0 FSiTS32.0 FSiT (8P Chassis)TTMk22.0TTSMk2 8J (2009-2014)SeatLeonMk2 2005-2012Cupra 2.0 TFSiSkodaOctavia2.0 FSiTVolkswagenGolfMK5ED30GTIMK6ED35RSciroccoR The kit also blanks off the port on the end of the inlet manifold that used to go to the PCV, and replaces it with our FMBGFK2 boost gauge fitting kit. This comes complete with 3 vacuum hose takeoffs and blanking screws so you can run a boost gauge, water spray controller, or you can blank them all off, it’s up to you. The kit comes complete will all parts necessary for installation and a full set of instructions. This product will fit the following vehicles: S3 (8P) 2.0 TFSI 265 PS (195 kW; 261 hp) BHZ/CDLA 2006–2013TT (8J) Mk2 2.0 TFSI 155 kW (211 PS; 208 bhp)  EA888   2010–TT (8J) Mk2 2.0 TFSI 155 kW (211 PS; 208 bhp)   2008–Leon Copa 2.0 TFSi 210 kW (286 PS; 282 bhp)  EA113  2008–Leon FR 2.0 TFSi 154 kW (209 PS; 207 bhp) CCZB/CAWB  2009–Scirocco Mk3 R 2.0 FSI 265 PS (195 kW; 261 hp) EA113)  2009–Golf Mk5 GTI 200bhpGolf Mk5 Edition30 Disclaimer: Any decision to install this product must rest solely with the purchaser as installation may adversely effect the manufacturers desired engine functionality or environmental pollution control measures. All responsibilities and liabilities remain with the customer and not Forge Motorsport.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Excess crankcase pressure is vented from the crankcase through the PCV system, where it is drawn into the intake manifold and returned by the engine. This recirculated air contains aerated oil from the crankcase which is burned by the engine. Turbo charged engines often draw significant amounts of oil into the engine through the PCV system.  This oil catch tank system removes aerated oil so that it can be drained and recycled. The kit is suitable for intallation to the 2 litre FSi engines such as in the VW MK5 Golf , MK5 Golf Edition 30 and SEAT Leon Cupra (not for engine codes CCTA CBFA). FITS: AudiA32.0 FSiTS32.0 FSiT (8P Chassis)TTMk22.0SeatLeonMk2 2005-2012Cupra 2.0 TFSiVolkswagenGolfMK5ED30GTI Depending on geographic location certain models listed in the compatible vehicles drop down menu are fitted with a charcoal filter to meet local emissions regulations. The filter is located at the front of the engine bay (on the left as you open the bonnet); also see black plastic canister in the engine bay image shown above. This kit with part number FMMK5CT is for models not fitted with the charcoal filter. If you do have the charcoal filter as standard an alternative catch tank kit is available under the product code FMMK5CTC. Please contact us by email or phone if you are unsure of which kit is compatible with your model.     Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This oil catch tank kit is the product of many months of intensive research and development by our in-house development team, and the end result is by far the most complete oil collection system currently on the market. Not only is it beautifully designed, it has been created to capture the maximum amount of harmful contaminants, including oil deposits, unused fuel vapours and moisture, all of which would ordinarily make their way back through to the inlet of the engine. Extensive testing has proven our oil catch tank kit's ability to effectively reduce sludge and carbon build up, in turn allowing the Golf Mk5 GTI's TSI engine to both breathe and perform more efficiently. It can therefore be viewed as a genuine performance enhancing product and one we recommend any Mk5 GTI owner seriously consider, particularly if they are planning more advanced power tuning at a later date.   The 0.4l (400cc) catch tank boasts a slew of features intended to make it both easy to check and simple to drain, including a dipstick for level inspection.   The design of the kit has also been carefully considered, hence its inner tube which is constructed from anti-static smooth fuel resistant nitrile rubber. This is paired with an outer cover made from reinforced stainless steel wire braid (a Forge specialty), specifically a partial inner braid and a full cover outer braid. We developed this complex arrangement in order for the tank to be resistant to both pressure expansion and vacuum collapse, and also to enable the kit to function within a clearly defined temperature range – 54°C to +150°C (-65°F to 300°F)   Finally, the kit features a pair of stainless steel reinforced oil resistant hoses with black external braiding, which combine with the supplied fittings to form an OEM-looking product when installed. Highlights 0.4L capacity* A dipstick for simple level inspection. 2 Quality stainless steel reinforced oil resistant hoses with black external braiding for that inconspicuous look. Fully assembled with fittings to suit the OEM connections. Inner tube is constructed from anti-static smooth fuel resistant nitrile rubber Outer cover is constructed from reinforced Stainless Steel wire braid consisting of partial inner braid & full cover outer braiding which is resistant to pressure expansion and vacuum collapse Temperature Range: -54°C to +150°C (-65°F to 300°F) Installation is straight forward with all necessary fittings and instructions included. Please note that the engine cover will not fit with this kit without modification              *Dipstick level is set at less than 0.4L for optimum breathing.       Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

A set of 5 Silicone Coolant hoses for the MK5 2 Litre Golf. These hoses are sold as an additional set to our FMKC010 hose kit and are often referred to as the lower hose kit. Our coolant hoses, unlike other manufacturers inferior hoses, are lined with Flurosilicone to ensure they can withstand the coolants used in modern engines. Please select your colour choice in the options above when ordering.   The Forge silicone hoses in this kit have been designed to include an expensive inner liner of modified silicone known as Fluorosilicone. This means the hoses are suitable to be used with  either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically The use of a Fluorosilicone liner ensures that Forge silicone hoses are the clear market leader. Lifetime warranty* FITS: AudiA32.0 FSiTS32.0 FSiT (8P Chassis)SeatLeonMk2 2005-2012Cupra 2.0 TFSiVolkswagenGolfMK5ED30GTI *T&C’s apply   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   FITS MULTIPLE VEHICLES

Read more less

A replacement turbo actuator for vehicles based on the MK5 Golf chassis with the 2.0 FSi engine. Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACVAG06 Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   Fits Multiple Cars

Read more less