Performance - Audi RS4 B7 (2004-2008)

Product Details Having the right tools for the job at hand makes any task much easier, and less time consuming. This Schwaben VAG Connector Removal Tool can easily be a best friend to any DIY enthusiast. The tool fits directly on the push & pull style VAG connector and gives just the perfect amount of leverage to release the connector and not break the tab. This style connector is often found on mass air flow (MAF) sensor, coil packs, headlights/fog lights, level sensors, MAP sensors, and etc.. A large ergonomic ball that fits into your palm is also fitted on the end of the tool for extra grip when pulling the connector off. Save your connectors, your thumbs, and some time with this innovative tool from Schwaben Tools. For California Prop 65 warning see:  www.P65Warnings.ca.gov. and photo below. Cross Reference tools This Part Fits the Following Vehicles Make Model Submodel Engine Audi All All All Porsche All All All Volkswagen All All All *The above product applications have been written by ECS Tuning. All warranties, product application, fitment, and performance are the responsibility of ECS Tuning. For additional information see the terms of use.

Read more less

Safety first! Make sure to use our Schwaben wheel chocks when using your ramps. All-rubber wheel chocks. Tailored to use with all Schwaben ramp products. Cross Reference tools, schwaben This Part Fits the Following Vehicles Make Model Submodel Engine Audi All All All BMW All All All Mercedes Benz All All All MINI All All All Porsche All All All Volkswagen All All All *The above product applications have been written by ECS Tuning. All warranties, product application, fitment, and performance are the responsibility of ECS Tuning. For additional information see the terms of use.

Read more less

This kit has been designed to address the weakness of the stock oil cooler – the cooler fitted to your car from Audi is aluminium, but the fittings on the ends of the cooler hoses are steel. The result is corrosion between the two different metals which cracks the fittings over time, causing a slow oil leak that gets worse with age, and eventually ends in a catastrophic failure of the oil cooler lines - and if you are unlucky, the engine too. Due to the corrosion setting in on the lines, they usually cannot be removed from the oil cooler without damaging it. This results in the need for the oil cooler and both lines to be replaced at a cost of over £1100 from the dealer, before you factor in consumables and labour to change the parts. Our solution uses tried and test products. It is a full replacement right from the fitting on the engine block which is precision made from 6082 billet aluminium, and then anodised to prevent any possibility of corrosion. This fitting leads to -12 AN Hose Technik black anodised aluminium fittings on Hose Technik braided lines with black overbraid. Cooling is accomplished by a 19 row Setrab oil cooler, the same manufacturer that supplies Audi and several F1 teams, again with a black finish. All the mating parts are similar materials and are tried and tested in Motorsport - there is no fear of corrosion affecting the fittings after a few years of use. The cooler is supported on a laser cut and powder coated frame that also holds the Audi fan control module in place. With everything finished in black, it makes for the ultimate stealth installation and unless you know what you are looking for, you won’t see it. The original remit of this replacement was to do away with all the troublesome Audi parts, which this kit accomplishes, but by relocating the oil cooler slightly higher than stock, we have also reduced the chances of damage from road debris. All parts needed for installation are included - bolts, nuts, washers, brackets, and full instructions, though you will need up to additional 2 litres of engine oil to account for the loss from removing your old oil cooler, and for filling the new cooler and lines.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

to suit disc size: 340mm This compound has been designed specifically for road use. It combines many of the characteristics found in a pure racing material (high friction, absence of fade) but has improved cold performance, and reduced disc wear and noise.The key features of DS Performance are:High friction coefficient (0.46 average)Excellent disc lifeLow wheel dustRacing "feel"Low heat transmission to caliper - thus avoiding fluid boilDS Performance is recommended for road use only. R90 compliant (EU standard for road pads).

Read more less

Type of Application:DS2500 - Off Road Use'Track Day' - Front and Rear of vehicle'Rally' - Rear of vehicle'Circuit Sprint' - Rear of vehicle'Formula' - Front and Rear of vehicle DS3000 - Off Road Use'Rally' - Front and Rear of vehicle'Circuit Sprint' - Front of vehicle'Formula' - Front and Rear of vehicle As a general guide we recommend that you consider the following when making your material compound selection: 4WD cars = same compound front and rear Rear traction cars = same compound front and rear. Front traction cars = high friction level in the front axle (i.e. DS3000), lower friction level on the rear axle (i.e. DS2500, 4003). For further advice please contact us. DS2500 (H)Track day & light race use for all vehicle types.Road style refinement but with race material ability to withstand heat with respect to life and μ.Average friction coefficient of 0.42 over working temperature range of 20°C to 500°C. DS3000 (R)Heavy duty all-round material choice.Multiple applications - touring car, rally, single seat.Average friction coefficient of 0.48 over working temperature range of 200°C to 650°C.

Read more less

Important Notes: Adds +/- 0.5deg Camber Whiteline Fixed Camber kits provide additional camber angle resulting in increased grip during cornering and traction under power. The kit includes low compliance synthetic elastomer bushings which maintain preferred alignment settings as well as enhanced steering response. WARRANTY: Backed by a 3 year warranty Compatible With: AUDI A4 B5 (TYP 8D) 6/1996-4/2000 AUDI A4 B6 (TYP 8E AND 8H) 2000-2006 AUDI A4 B7 (TYP 8E AND 8H) INCL QUATTRO 2004-2008 AUDI A4 B8 (TYP 8K) INCL QUATTRO 11/2008-2016 AUDI A6 C5 (TYP 4B) INCL QUATTRO 1997-2004 AUDI A6 C6 (TYP 4F) INCL QUATTRO 2004-2011 AUDI A8 D2 (TYP 4D) INCL QUATTRO 1994-2002 AUDI S4 B5 (TYP 8D) INCL RS4 10/1997-9/2001 AUDI S4 B6 (TYP 8E AND 8H) INCL RS4 3/2002-12/2004 AUDI S4 B7 (TYP 8E AND 8H) INCL RS4 11/2004-6/2008 AUDI S4 B8 (TYP 8K) INCL RS4 11/2008-2016 AUDI S6 C5 (TYP 4B) INCL RS6 1999-2003 AUDI S6 C6 (TYP 4F) INCL RS6 2006-2011 AUDI S8 D2 (TYP 4D) 1994-2002 VOLKSWAGEN PASSAT B5 AND B5.5 (TYP 3B AND 3BG) 1996-2005

Read more less

Our disc installation kit comes with everything you need to install these 2 piece discs to your Audi RS4 B7. The 2 piece brake discs are assembled with outer rotors made by AP Racing which are of the highest quality steel and come in either a grooved or drilled. Matched with our lightweight aluminium bells finished anodised in black, this brake disc setup is a floating 2 piece assembly and the float is in the disc bell rather than the disc. New pads are highly recommended to be installed. Included in our kit:2x 362x32 2 piece front brake discs To complete this front brake kit you will need:1x Set of brake pads to suit your driving style

Read more less

Our disc installation kits come with everything you need to install a big brake kit excluding the calipers and pads, allowing you the quality of Vagbremtechnic products with the option to source and supply your own 'bargin' priced new or second-hand  8 Piston Brembo Calipers which can be found from the Audi RS4 B7 / Audi R8 / Lamborghini Gallardo. The caliper carriers are made from lightweight aluminium. These have steel thread inserts for strength along with a black anodised finish. The supplied front brake lines have been made to our specifications by HEL Performance, which include stainless steel fittings and are finished in their carbon black sheathing. The 2 piece brake discs are assembled with outer rotors made by AP Racing which are of the highest quality steel and come in either a grooved or drilled. Matched with our lightweight aluminium bells finished anodised in black, this brake disc setup is a floating 2 piece assembly and the float is in the disc bell rather than the disc. Lastly the fitting kit includes bolts that are high tensile M12x1.25 coupled with quality spring washers. Included in our kit: 2x Caliper carriers2x 362x32 2 piece front brake discs (Grooved or Drilled)1x Braided front brake lines4x Caliper to carrier bolts4x Spring washers for caliper to carrier bolts To complete this front brake kit you will need:2x 8 Piston Brembo caliper from Audi RS4 B7 / Audi R8 / Lamborghini Gallardo1x Set of brake pads to suit your driving styleBrake fluid to flush system when installing   FITS:  AUDI A3 8P AUDI S3 8P AUDI A3 8V AUDI S3 8V AUDI TT 8J AUDI TTRS 8J AUDI TT 8S SEAT LEON MK2 1P SEAT LEON MK3 5F SEAT TOLEDO 5P SKODA OCTAVIA MK2 1Z SKODA OCTAVIA MK3 5E VW CADDY MK3 2K VW EOS 1F VW GOLF MK5 VW GOLF MK6 VW GOLF MK7 VW JETTA 1K VW PASSAT B6 VW PASSAT CC VW SCIROCCO

Read more less

Our disc installation kits come with everything you need to install a big brake kit excluding the calipers and pads, allowing you the quality of Vagbremtechnic products with the option to source and supply your own ‘bargin’ priced new or second-hand  8 Piston Brembo Calipers which can be found from the Audi RS4 B7 / Audi R8 / Lamborghini Gallardo. The caliper carriers are made from lightweight aluminium. These have steel thread inserts for strength along with a black anodised finish. The supplied front brake lines have been made to our specifications by HEL Performance, which include stainless steel fittings and are finished in their carbon black sheathing. The 2 piece brake discs are assembled with outer rotors made by AP Racing which are of the highest quality steel and come in either a grooved or drilled. Matched with our lightweight aluminium bells finished anodised in black, this brake disc setup is a floating 2 piece assembly and the float is in the disc bell rather than the disc. Lastly the fitting kit includes bolts that are high tensile M12x1.25 coupled with quality spring washers. Included in our kit:2x Caliper carriers2x 362×32 2 piece front brake discs1x Braided front brake lines4x Caliper to carrier bolts4x Spring washers for caliper to carrier bolts To complete this front brake kit you will need:2x 8 Piston Brembo caliper from Audi RS4 B7 / Audi R8 / Lamborghini Gallardo1x Set of brake pads to suit your driving styleBrake fluid to flush system when installing

Read more less

Our disc installation kits come with everything you need to install a big brake kit excluding the calipers and pads, allowing you the quality of Vagbremtechnic products with the option to source and supply your own 'bargin' priced new or second-hand  8 Piston Brembo Calipers which can be found from the Audi RS4 B7 / Audi R8 / Lamborghini Gallardo. The caliper carriers are made from steel for strength. The supplied front brake lines have been made to our specifications by HEL Performance, which include stainless steel fittings and are finished in their carbon black sheathing. The 2 piece brake discs are assembled with outer rotors made by AP Racing which are of the highest quality steel and come in either a grooved or drilled. Matched with our lightweight aluminium bells finished anodised in black, this brake disc setup is a non-floating 2 piece assembly. Lastly the fitting kit includes bolts that are high tensile M12x1.25 coupled with A2 stainless spring washers. Included in our kit:2x Caliper carriers2x 362x32 2 piece front brake discs (Grooved or Drilled)1x Braided front brake lines4x Caliper to carrier bolts4x Spring washers for caliper to carrier bolts To complete this front brake kit you will need:2x 8 Piston Brembo caliper from Audi RS4 B7 / Audi R8 / Lamborghini Gallardo1x Set of brake pads to suit your driving styleBrake fluid to flush system when installing

Read more less

Our disc installation kits come with everything you need to install a big brake kit excluding the calipers and pads, allowing you the quality of Vagbremtechnic products with the option to source and supply your own 'bargin' priced new or second-hand  8 Piston Brembo Calipers which can be found from the Audi RS4 B7 / Audi R8 / Lamborghini Gallardo. The caliper carriers are made from steel for strength. The supplied front brake lines have been made to our specifications by HEL Performance, which include stainless steel fittings and are finished in their carbon black sheathing. The 2 piece brake discs are assembled with outer rotors made by AP Racing which are of the highest quality steel and come in either a grooved or drilled. Matched with our lightweight aluminium bells finished anodised in black, this brake disc setup is a non-floating 2 piece assembly. Lastly the fitting kit includes bolts that are high tensile M12x1.25 coupled with A2 stainless spring washers. Included in our kit:2x Caliper carriers2x 362x32 2 piece front brake discs (Grooved or Drilled)1x Braided front brake lines4x Caliper to carrier bolts4x Spring washers for caliper to carrier bolts To complete this front brake kit you will need:2x 8 Piston Brembo caliper from Audi RS4 B7 / Audi R8 / Lamborghini Gallardo1x Set of brake pads to suit your driving styleBrake fluid to flush system when installing

Read more less

The calipers included in this kit come from the Audi TTRS / RS3 8P and are made by Brembo. The piston sizes are matched extremely well to provide a pedal feel that is just like OEM. The calipers are offered in black, silver, grey or red without a logo but we can offer these calipers in almost any colour with or without almost any logo. The caliper carriers are made from lightweight aluminium. These have steel thread inserts for strength along with a black anodised finish. The supplied front brake lines have been made to our specifications by HEL Performance, which include stainless steel fittings and are finished in their carbon black sheathing. The 2 piece brake discs are assembled with outer rotors made by AP Racing which are of the highest quality steel and come in either a grooved or drilled. Matched with our lightweight aluminium bells finished anodised in black, this brake disc setup is a floating 2 piece assembly and the float is in the disc bell rather than the disc. Lastly the fitting kit includes bolts that are high tensile M12x1.25 coupled with quality spring washers. Included in our kit:2x 4 Piston Brembo calipers2x Caliper carriers2x 362x32 2 piece front brake discs (Grooved or Drilled)1x Braided front brake lines4x Caliper to carrier bolts4x Spring washers for caliper to carrier bolts To complete this front brake kit you will need:1x Set of brake pads to suit your driving styleBrake fluid to flush system when installing FITS: AUDI A4 B5 AUDI A4 B6 AUDI A4 B7 AUDI S4 B5 AUDI S4 B6 AUDI S4 B7

Read more less