Features
Improved throttle response
Black powder coated air box lid with bonnet seal
Dyno results: max gains 13-22hp (this may vary dependant on vehicle)
Easy to maintain dry pleated filter
What Does It Do?
This induction kit delivers increased air flow and induction noise over the standard restrictive air box. Whether this kit is being installed to a standard vehicle or to an already tuned vehicle, you can be sure of the positive performance gains this will deliver.
What Will I Get?
MST Performance utilise the top quality components in all of their kits see below for what this kit will include.
Black powder coated air box lid / heat shield
Red pleated filter
Fitment Compatibility Chart
This product fits the following:
Year
Make
Model
Engine
2014-2019
Ford
Focus (MK3)
1.5 EcoBoost
Ford Focus MK3.5 1.5T Inlet Pipe (FO-MK304)
MST Performance have developed this silicone boost hose kit for the MK3.5 Ford Focus 1.5T engines. Using our silicone pipes to replace the OEM plastic pipe design that restricts airflow & can breakdown. Creating more power & better turbo response. The smooth interior of the silicone pipes maximizes the airflow and allows for big tuning.
Vehicle Fitment2011 – 2018, Ford FOCUS MK3.5 1.5T
Fitment Compatibility Chart
This product fits the following:
Year
Make
Model
Engine
2014-2019
Ford
Focus (MK3)
1.5 EcoBoost
Ford Focus MK3 TDCI Silicone Boost Pipe (FO-MK303)
Features– Maintain smooth inside surface for optimum flow to reduces turbulence and increase airflow capacity– 5-Ply and 3-Ply silicone construction– stainless steel wire reinforced– Direct replacement of the factory rubber hoses– Designed to maximize airflow through the intake tract by reducing expansion
Vehicle Fitment2011 – 2018, Ford Focus (MK3), TDCI
Fitment Compatibility Chart
This product fits the following:
Year
Make
Model
Engine
2010-2018
Ford
Focus (MK3)
1.6 TDCi
2010-2018
Ford
Focus (MK3)
1.8 TDCi
2010-2018
Ford
Focus (MK3)
2.0 TDCi
Manufactured from fibreglass and comes pre finished and sprayed in a gloss black paint.
This spoiler lip requires bonding on using a polyuerthane adhesive (such as tigerseal).
Manufactured from Lloyds approved Grp materials to a very high standard.
This product comes in Gloss black exactly as pictured with all fixings required.
Manufactured from Lloyds approved Grp materials to a very nigh standard.
This product comes in Gloss black exactly as pictured with all fixings required.
Manufactured from Lloyds approved Grp materials to a very high standard.
This product comes in Gloss black exactly as pictured with all fixings required.
Definition of a front splitter - Front splitters are essential aerodynamic components that serve to balance the front vs. rear distribution of downforce. A splitter is typically found on the front-end of a race car, appearing as a flat extension to the very bottom of the front bumper
Our Focus MK3 RS V2 front splitter, Specifically styled design that follows the curves and angles of the RS's front bumper. The V2 Splitter is designed to sit higher than our original RS splitter making it a more practical option for the Lowered RS.
This product is manufactured utilising time proven composite technology.
They are supplied as pictured in a gloss black gell coat ready to fit.
The splitter is supplied with a full stainless steel fitting kit.
Definition of a front splitter - Front splitters are essential aerodynamic components that serve to balance the front vs. rear distribution of downforce. A splitter is typically found on the front-end of a race car, appearing as a flat extension to the very bottom of the front bumper.
Our Focus MK3 RS front splitter, Specifically styled design that follows the curves and angles of the RS's front bumper. This splitter will add around 2" to the centre section of the bumper, giving the front end the well suited low agressive look.
This product is manufactured utilising time proven composite technology.This splitter is supplied as pictured in a gloss black gell coat, along with a comprehensive stainless steel fixing kit, Branded with our TRC gel badge, ready to fit.This product is supplied with a laser cut bracket to support the middle of the splitter.
Our fog light extension are the perfect way to give your ST's front end a little more agression.These are manufactured in Nylon12 and supplied in a mottled charcoal/black as in the latter pictures.We advise that these are bonded using a polyurethane adhesive such a as tiger seal for maximum safety and securityThese can be painted if required by a bodyshop.
Manufactured from Lloyds approved Grp materials to a very high standard.
This product comes in finished in a gloss black gel coat exactly as pictured with all fixings required.
NEW AND IMPROVED FITMENT!
Manufactured from fibreglass and supplied as pictured in a gloss black gell coat ready to fit.
This product is supplied with fixings and is a simple direct fit.Please note if your ST is running our splitter this will need to be removed for install of the chin lip.
Definition of a front splitter - Front splitters are essential aerodynamic components that serve to balance the front vs. rear distribution of downforce. A splitter is typically found on the front-end of a race car, appearing as a flat extension to the very bottom of the front bumper
Our Focus MK3.5 ST front splitter, Specifically styled design that follows the curves and angles of the front bumper. This splitter finishes of the front end perfectly with its added depth that the ST should have come with from factory.
This product is manufactured utilising time proven composite technology.
They are supplied as pictured in a gloss black gell coat ready to fit.
The splitter is supplied with a full stainless steel fitting kit.
Definition of a front splitter - Front splitters are essential aerodynamic components that serve to balance the front vs. rear distribution of downforce. A splitter is typically found on the front-end of a race car, appearing as a flat extension to the very bottom of the front bumper
Our Focus MK3.5 ST front splitter, Specifically styled design that follows the curves and angles of the front bumper. This finishes of the front end perfectly with its added depth that the ST should have come with from factory.
This product is manufactured utilising time proven composite technology.
This splitter is supplied as pictured in a gloss black gell coat, along with a comprehensive stainless steel fixing kit, Branded with our TRC gel badge, ready to fit.
Manufactured from Lloyds approved Grp materials to a very high standard.
This product comes in Gloss black exactly as pictured with all fixings required.
The spoiler lip comes in a sprayed gloss back finish ready to fit
For fitting this requires bonding on using a polyuerthane adhesive (such as tigerseal).
Manufactured from fibreglass and supplied as pictured in a gloss black gell coat ready to fit.
It comes with a full stainless steel fitting kit and is a simple direct fit.
Definition of a front splitter - Front splitters are essential aerodynamic components that serve to balance the front vs. rear distribution of downforce. A splitter is typically found on the front-end of a race car, appearing as a flat extension to the very bottom of the front bumper
Our Focus MK3 PFL front splitter, Specifically styled design that follows the curves of the front bumper. This splitter finishes the front end perfectly with the added depth that the Focus ST should have come with as standard.
This product is manufactured utilising time proven composite technology.This splitter is supplied as pictured in a gloss black gell coat, along with a comprehensive stainless steel fixing kit, Branded with our TRC gel badge, ready to fit.
Manufactured from Lloyds approved Grp materials to a very high standard.
This product comes in Gloss black exactly as pictured with all fixings required.
Definition of a front splitter - Front splitters are essential aerodynamic components that serve to balance the front vs. rear distribution of downforce. A splitter is typically found on the front-end of a race car, appearing as a flat extension to the very bottom of the front bumper
Our MK3.5 Focus ST-Line front splitter, Specifically styled design that follows the curves and angles of the front bumper.
This product is manufactured utilising time proven composite technology.
They are supplied as pictured in a gloss black gell coat ready to fit.
The splitter is supplied with a full stainless steel fitting kit.
Our brows are now manufactured using a new process to insure they are one of the thinnest available on the market today. They measure between 1-1.5mm, thus preventing 'bonnet rub'.
These Brows will fit all Focus MK3 (pre-facelift headlights)
Manufactured from fibreglass and supplied as pictured in a gloss black gell coat ready to fit.We advise to use a small amount of polyurethane adhesive (such as tigerseal) to help secure the brows when fitting.
Our brows are now manufactured using a new process to insure they are one of the thinnest available on the market today. They measure between 1-1.5mm, thus preventing 'bonnet rub'.
These Brows will fit all Focus MK3 (pre-facelift headlights)
Manufactured from fibreglass and supplied as pictured in a gloss black gell coat ready to fit.We advise to use a small amount of polyurethane adhesive (such as tigerseal) to help secure the brows when fitting.
Manufactured from Lloyds approved Grp materials to a very high standard.
This product comes in Gloss black exactly as pictured with all fixings required.
