All

A set of three coolant hoses for the Suzuki Swift Sport 1.4 ZC33S, which replace three of the OEM rubber hoses in the coolant system. The kit consists of the upper radiator hose, lower radiator hose, and radiator overflow hose. Forge designed these silicone hoses so they can withstand pressures that can be experienced on tuned and remapped engines. They will long outlast the original hoses and with our limited lifetime warranty on all Forge products, you can be sure these hoses won't let you down. Available in red, blue, or black - Please select your choice in the options above when ordering. A complete High quality stainless steel hose clamp set for the above hoses are available from the drop down menu. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically Lifetime warranty*   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This actuator is designed for the Toyota GT4 Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACGT4 Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 3, 048 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This oil catch tank kit is for the Toyota Supra A90 and BMW Z4 with the BMW B58 Engine, developed by our in-house development team. Not only is it beautifully designed, it has been created to capture the maximum amount of harmful contaminants, including oil deposits, unused fuel vapours and moisture, all of which would ordinarily make their way back through to the inlet of the engine. FITS: BMWZ4ToyotaSupraMk5 A90 When the B58 engine is tuned heavily blow by can occur resulting in poor breathing our specifically designed catch can system and extensive testing has proven our oil catch tank kit's ability to effectively reduce sludge and carbon build up, in turn allowing the engine to both breathe and perform more efficiently. It can therefore be viewed as a genuine performance enhancing product and one we recommend, particularly if you are planning more advanced power tuning at a later date. With aesthetics also in mind our catch can has the bracket incorporated into the catch can lid and is placed behind the factory airbox heat shield meaning this important component can still be kept in situ. The 0.4l (400cc) catch tank boasts a slew of features intended to make it both easy to check and simple to drain, including a dipstick for level inspection. The design of the breather adaptor and catch can was formed using the latest 3D solidworks software and engineered for a complete plug and play solution with no cutting or modifying of original components meaning the vehicle can return to stock in just under a hour. The design of the kit has also been carefully considered, hence its inner tube which is constructed from anti-static smooth fuel resistant nitrile rubber. This is paired with an outer cover made from reinforced stainless steel wire braid (a Forge specialty), specifically a partial inner braid and a full cover outer braid. We developed this complex arrangement in order for the tank to be resistant to both pressure expansion and vacuum collapse, and also to enable the kit to function within a clearly defined temperature range – 54°C to +150°C (-65°F to 300°F) Finally, this kit includes machined billet fittings that are anodised black to form an OEM-looking product when installed.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

A replacement turbo actuator for the Audi TTRS and RS3 (8P) models . Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACTTRS Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

A turbo actuator for the Corsa VXR and Astra 1.6 GTC. VauxhallAstraJ (2009-2016)2011-2014 (1.6T)CorsaD (2010-2015)2010-2015 (1.6T VXR) Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACCVXR Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

A serviceable turbo actuator for both the Hyundai Veloster and Kia Cee'd GT 1.6 Turbo. This unit can be modified to suit various boost pressure requirements upon request. FITS; HyundaiVelosterTurbo 2011-2018 1.6 GDIKiaCeedGT Turbo (-2018) Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACHTV Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Turbo Actuator for Renault Clio 200RS and Nissan Juke 1.6 Turbo. Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACTRCT Actuator1 x Forge Sticker This actuator is built with a yellow coded spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.

Read more less

FITS: VauxhallAstraH (2004-2013)2004-2007 (2.0T)2005-2011 (2.0T VXR)Zafira2011-2019 (1.4T)  with the Z20 engine and K04 turbo. Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACAVXR actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

A turbo actuator for the Vauxhall Astra VXR (J Type). Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACVXRJ Actuator1 x Forge Sticker This actuator is built with a green coded spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 3, 048 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

FITS: VauxhallAstraJ (2009-2016)2011-2015 (1.4T)CorsaD (2010-2015)2012-2015 (1.4T)E (2015 Onwards)(1.4T 2015 Onwards)Insignia2008-20142011-2014 (1.4T)Meriva2010-2017 (1.4T)Mokka2012-2017 (1.4T) Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACC14T Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.     Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This actuator is suitable for a number of engine installations in the 850,S60,S70,V70,C70 range. There are two variations of this actuator available, FMACT5S – with a straight connecting rod, and FMACT5B where the rod has an offset or bend. Please see the fitment lists below to determine which version should fit your vehicle: fits: Volvo850 T5V70/S70 FMACT5S (Straight Rod) This is compatible with the models below, with the Bosch Motronic 4.3 / 4.4 ECU fitted as standard, as seen in models with an accelerator cable. The original actuator rod is straight and suitable for the Mitsubishi TD04HL straight flanged turbo. • 850 R 1997 - 1998 • 850 T-5 1997 - 1998 • 850 T5-R 1997 - 1998 • S70 T5 1997 – 1998 • V70 T5 1997 – 1998 • C70 T5 1997 - 1998 FMACT5B (Bent Rod) This is compatible with the models seen below with Bosch Motoronic 7 and Motronic 7S ECU fitted as standard, as seen in models without an accelerator cable (drive by wire / ETM). The original actuator rod is stepped and suitable for the Mitsubishi TD04HL angled flanged turbo type. • S70 1999 - 2000 • C70 (phase 1 and 2) 1999 - 2005 • V70 (phase 1 and 2) 1999 – 2004 • S60 (phase 2) 2000 – 2004 If you have a later K24 Turbo models (2004/2005/2006 and 2007) with 6 speed manual or automatic gearbox, please see Forge Motorsport part number FMACS60R. Please select the actuator rod, straight or bent, and colour of spring in the options above. Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACT5 Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

The Forge Motorsport FMTUBL5 has been designed for the Fiat 500, 595, and 695 turbo (this will not fit those fitted with IHI turbo). This turbo blanket is designed to isolate the radiant heat produced by the turbocharger. FITS: Fiat500500Euro 6 Abarth595145BHPCompetizione 180BHPTrofeo 160BHP  Turismo 165BHP695XSR Yamaha Limited Edition 165BHP  Rivale 180BHPPuntoEvo 2010-2015Abarth Multiair This design has been created to withstand the harshest of environments and proven to withstand temperatures up to 2500°F (1370°C) of radiant heat which will assist in protecting and prolonging the life of engine components. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path which helps reduce turbo lag and air intake temperatures resulting in more power. Simple to fit using existing OEM hardware. Please note that a turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as this can cause damage to the blanket. ·       Stainless Steel Rivets·       Carbon fabric outer shell·       Calcium Magnesium Silicate Wool constructed Inner Core·       High temperature Silica fabric   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

The Forge turbo blankets are designed to isolate the radiant heat produced by the turbocharger. Designed by the Forge development team on the Forge VW Golf MK1 Race car in the harshest of environments and exceeding all expectations, the Forge turbo blanket is designed to assist in the protection and prolonging the life of the engine components. FITS: HondaCivicType R(FK2 2015-2017)(FK8 2017-2021) ·       Stainless Steel Rivets·       Stainless Steel Fasteners·       Carbon fabric Outer Shell·       Calcium Magnesium Silicate Wool constructed Inner Core·       High temperature silica fabric The unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power.  Interior Surface: ·       Max Temperature Rating: 2300°F/1260°C·       Continuous Use Limit: 1832°F1000°C Exterior Surface: ·       Direct Contact Limit: 1800°F/982°C·       Radiant Heat Limit: 2500°F/1371°C   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

The Forge Motorsport FMTUBL4 has been specifically designed for the Mini R56 stock turbo charger, and also fits the Peugeot 207/208 GTI. This turbo blanket is designed to isolate the radiant heat produced by the turbocharger. The stock Mini heat shield is inadequate and can result in warping the standard air scoop located in the bonnet. This design has been created to withstand the harshest of environments and proven to withstand temperatures up to 2500 °f of radiant heat which will assist in protecting and prolonging the life of engine components. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path which helps reduce turbo lag and air intake temperatures resulting in more power. Please note that a turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as this can cause damage to the blanket.   ·       Stainless Steel Rivets ·       Stainless Steel Fasteners ·       Carbon fabric outer shell ·       Calcium Magnesium Silicate Wool constructed Inner Core ·       High temperature Silica fabric   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Fits Peugeot 308 GTI MK2 Proven to withstand temperatures up to 2500°F or 1370°C Prolongs the life of engine components Improves the appearance of the 308’s engine bay Stainless Steel Rivets and Fasteners Carbon fabric outer shell Calcium Magnesium Silicate Wool constructed Inner Core High temperature Silica fabric   The Forge Motorsport FMTUBL14 is a turbo blanket that has been specifically designed for the Peugeot 308 GTI MK2. This turbo blanket is designed to isolate the radiant heat produced by the turbocharger. The OE heat shield still allows a considerable amount of heat transfer thus creating a warmer engine compartment, which will have an effect on the engines components and increase intake temperatures. This design has been created to withstand the harshest of environments and proven to withstand temperatures up to 2500°F of radiant heat which will assist in protecting and prolonging the life of engine components. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path which helps reduce turbo lag and air intake temperatures resulting in more power. As a bonus the FMTUBL14 improves the appearance of the 308’s engine bay considerably, The OEM turbo heat shield tarnishes over many heat cycles, a problem which does not affect Forge Motorsport turbo blankets. All Forge Motorsport turbo blankets are designed and manufactured to the highest standards and use superior materials, unlike some turbo blankets which are constructed using substandard materials.

Read more less

Product Description With Forge Motorsport leading the way in aftermarket products for the Hyundai N division vehicles, we are proud to present our Turbo Inlet Adaptor and Intake Tract for the Hyundai i20N. The kit is a full plug and play solution, with a replacement cast turbo inlet adaptor, CNC machined hose couplers, and a silicone high flow inlet hose. Available in a choice of Black, Red, and Performance Blue, the TIA11 will not only increase your Hyundai’s performance, but it also transforms the look and aesthetics of your vehicle’s engine bay.   The size of the inlet elbow has increased by over 170% to maximise the amount of air that can physically flow to the turbo from the inlet tract. The OEM factory alloy cast elbow is small, so we knew that this would be the key component to target as tuners start to increase the boost levels and performance output of the 1.6l turbocharged combustion engine. As well as this, the plastic OEM inlet hose has ribs and steps within the bore, causing detrimental turbulence while disturbing and slowing the airflow. By removing the ribs and steps, the larger Forge Motorsport silicone turbo inlet hose reduces the amount of turbulence over the standard item, enabling better airflow. Why do we use silicone? In the development process we tested an oversized aluminium pipe and found that it started to show signs of heat soak, this had a detriment to the impressive initial power gains. We also found after the third pull on the Dyno, the alloy pipe conducted too much heat on this application and started to decrease the gains. When using silicone, heat cannot be conducted as well, therefore even after six pulls, the silicone hose stayed at a steady temperature and did not decrease the power whatsoever. The inlet pipe fits directly to the factory airbox along with our FMINDK45 performance intake solution. The turbo inlet adaptor improves your vehicles airflow in several ways; designed in a similar way to a conventional velocity stack, it routes the air directly into your turbo charger and allows more air to be compressed due to its larger capacity, this has a positive effect when accelerating your vehicle after long deceleration, or in-between gear changes, due to more air being kept within the intake system. Dyno Results Testing was completed using Performance Remap in Gloucester with their VTEC 4-wheel drive dynamometer, this was to ensure all our data is achieved with results as accurately as possible by an independent tuner. As you can see from the dyno results below, peak power was increased from stock by nearly 7 BHP and 12NM of torque when mated to the OEM airbox and standard factory filter. The best news is that there are significant gains across the entire rev range, meaning that the car will pick up quicker and pull the whole way through to redline. TIA11 also benefits from a 17NM of power gain between 2500 RPM and 3000 rpm, this is right as the power comes in and can really change the feel and power delivery when behind the wheel. To compliment the turbo inlet, it can be matched to our induction kit FMINDK45. As you can see below this gave an increase of 12BHP and a torque increase of 20NM both at peak. These two products really do complement each other superbly both in conjunction, and as standalone modifications. After installing a tuning box, or re-calibrating the ECU with stage one or two tunes, the performance yields can be expected to be a lot higher than the figures stated. Testing on the dyno certainly represents the benefits from such a well-engineered product; this coupled with our Lifetime Warranty is just the reason to choose Forge for your Hyundai’s performance hardware.

Read more less

Twin Turbo Actuators for Porsche 996 and GT2. Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:2 x FMAC996 Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This Blow Off, or Dump valve, is for the Mercedes 2.0 Turbo GDi engine found in the CLA250 that has the electronically controlled bypass valve. It is recommended for any vehicle where the boost pressure has been increased by an ECU software upgrade and for unmodified vehicles operating in warmer climates, as a solution to the many failures that have occurred where the original rubber diaphragm splits, which causes a loss of boost pressure. Unfortunately the failure doesn’t always result in a check engine light as the valve can still be blown open by the boost pressure, so you may not be aware that you are losing power due to this. FITS: MercedesA Class W176 (2012-2018)A160A180A200A220A250B-Class W246 (2011-2018)B160B180B200B220B250CLA Class C117 (2013-2019)CLA180CLA200CLA250GLA Class X156 (2014-2019)GLA180GLA200GLA250GLC Class X253 (2015-2019)GLC200GLC250 Our alternative is a fully engineered solution offering significantly improved reliability. Our valve is piston based with no diaphragm to fail, and of all aluminium construction. It replaces the original unit with a pressure/vacuum operated piston valve that still also retains the desirable OEM ECU control over valve actuation. All parts require for installation are included, together with full installation instructions.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised

Read more less

This Recirculating valve is for the Mercedes 2.0 Turbo GDi engine found in the CLA250 that has the electronically controlled bypass valve. It is recommended for any vehicle where the boost pressure has been increased by an ECU software upgrade and for unmodified vehicles operating in warmer climates, as a solution to the many failures that have occurred where the original rubber diaphragm splits, which causes a loss of boost pressure. Unfortunately the failure doesn’t always result in a check engine light as the valve can still be blown open by the boost pressure, so you may not be aware that you are losing power due to this. fits: MercedesA Class W176 (2012-2018)A160A180A200A220A250B-Class W246 (2011-2018)B160B180B200B220B250CLA Class C117 (2013-2019)CLA180CLA200CLA250GLA Class X156 (2014-2019)GLA180GLA200GLA250GLC Class X253 (2015-2019)GLC200GLC250 Our alternative is a fully engineered solution offering significantly improved reliability. Our valve is piston based with no diaphragm to fail, and of all aluminium construction. It replaces the original unit with a pressure/vacuum operated piston valve that still also retains the desirable OEM ECU control over valve actuation. All parts require for installation are included, together with full installation instructions.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

  Similar to many of the newer VAG engines, the latest 1.0 TSI power plant is not equipped with a diverter valve fitted as standard, Forge Motorsport has developed a twin piston dump valve that not only gives you a loud audible sound when lifting off the throttle, but also increases the throttle response during gear changes by reducing turbo lag. It has been designed to help the turbocharger maintain its rotational speed ready for when you accelerate, whilst also taking the strain away from the impeller. Without removing this stress from your turbo, it can lead to premature failure especially on remapped engines and modified vehicles.       This valve kit allows the fitment of our fast response blow off valve preventing turbo surge and prolonging the life of your engine’s turbocharger. The kit includes all the necessary hardware and step by step installation instructions for any car enthusiast with appropriate garage tools to fit at home, in just a couple of hours!  Due to the exposed position of the OEM boost pipe and the nature of heat cycle, the plastic that the OEM pipe is made from can deteriorate over time, becoming brittle and susceptible to boost leaks. This kit totally replaces this plastic pipe from turbo to manifold with a multi-ply silicone hose (available in a choice of red or black). Highlights: CNC machined billet couplers and components CNC machined twin piston Forge valve. Two hose options: red or black (Custom colours available but will incur a 50% non-refundable deposit and a lead time of 8-10 weeks) Forge Motorsports dump valve will not bring on any check engine lights (EML)  The hose has a quality inner lining of modified silicone known as 'Fluorosilicone'. This means that the hose will stay bright and vibrant and will not deteriorate over time. Forge Motorsport lined hoses are suitable to be used with modern long-life coolants, Organic Acid Technology coolants (O.A.T.) and oil mist. The construction of the hose has been engineered to exceed that of the OEM fitments, the Forge Motorsport hose will enhance any engine bay both technically and aesthetically. We cannot guarantee that this product will fit with all aftermarket intakes. Lifetime warranty We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner Audi-A1 A1 GB 25/30 1/0 TSI (2022-)-A3 1.0 TSI (2022-)-Q21.0 TSI (2022-) A1A1 (GB) 25/30 1.0 TSI (2022-) A31.0 TSI (2022-) Q21.0 TSI (2022-) Seat Arona 1.0 TSI (2022-) Ateca 1.0 TSI (2022-) Ibiza Mk5 (KJ) 2017 - late 2021 1.0 TSI Mk5 (KJ) 2021- 1.0 TSI Leon Mk4 2022- 1.0 TSI Skoda Fabia PJ 2022- 1.0 TSI Kamiq 1.0 TSI (2022-) Karoq 1.0 TSI (2022-) Octavia 1.0 TSI (2022-) Scala 1.0 TSI (2022-) Volkswagen Golf MK8 1.0 TSI (2022-) Polo 1.0 TSI (2022-) T-Cross 1.0 TSI (2022-) T-Roc 1.0 TSI (2022-) Taigo 1.0 TSI (2022-) This part will take approximately 1 hour to fit.  

Read more less

Forge has developed this turbo outlet muffler delete pipe for the 2.0 petrol turbo (TSI) (EA888 GEN4 engine). This will not fit Golf R or Audi S3 8Y as this engine has no OEM turbo muffler. It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve throttle response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part.   On the new Golf GTI engine code DNP, this muffler delete gave an additional 8-10bhp during dyno tests. This will fit OEM part number 06Q145702B  

Read more less

Product Style: Oil Filters Anti Drain Back Valve: Yes Bypass Valve: Yes Filter Material: High Flow Premium Media Gasket Material: Nitrile Rubber Height: 3.75 in (95 mm) Outside Diameter: 3 in (76 mm) PSI Relief Valve: 11-14 Removal Nut: YesStyle: Canister Thread Specification: 3/4 In. - 16 Removal Nut Size: 1 inch Weight: 0.74 lb (0.34 kg) Product Box Length: 3.12 in (79 mm) Product Box Width: 3.12 in (79 mm) Product Box Height: 3.8 in (97 mm)

Read more less

This actuator is designed for the Audi A4 and Volkswagon Passat 1.8T engines that are longitudinally mounted. ( crankshaft of the engine runs inline or the length of the chassis) Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACVAG02 Actuator1 x Forge Sticker This actuator is built with a green coded spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

2.0 TSI EA888.3 & EA888.3BBillet magneticoil sump plugfor all Volkswagen  I  Audi  I  Cupra  I  Skoda Catch any particles in your oil with our new Magnetic Oil Sump Drain Plug to protect your 2.0 TSI EA888 gen3 & 3B engine. What doesit do? Our Magnetic Oil Sump Drain Plug is now available for the 1.8 & 2.0 TSI EA888 gen3 and 2.0 TSI gen3B engines. These engines use a plastic oil pan, meaning that normal metal, screw-in sump plugs simply can't be used. Our new 'True-Lock' fitting system means that, at last, you can protect your engine. By attracting and separating out the minute abrasive and ferrous metal particles that are carried by the oil, it prevents them from circulating throughout your engine’s lubrication systems. The harder your engine works, the greater the risk of nasty metallic debris, the greater the benefit of using a magnetic sump plug. Our unique 'True-Lock' fitting works with a simple quarter-turn to install the plug, then a PolyCarbonate locking ring ensures that it stays tight and sealed at all times. It's a lifetime-use plug - simply replace the O-ring at each service. Install couldn’t be simpler – insist on our new Magnetic Billet Sump Plug with your next oil-change and simply screw it in!  PRECISION ENGINEERED FOR PERFECT PERFORMANCE. The large surface area of the magnetic end ensures any metallic particles in your oil are collected. Clever quarter-turn thread fits straight into the factory oil-pan with no changes needed. CNC constructed from billet 6061-T6 aircraft grade aluminium with gloss-black anodised finish. PolyCarbonate retaining clip allow simple and secure fitment with each oil service. The white laser-etched RacingLine logo is all part of the detail. CONFIRMED APPLICATIONS VWR180004 2.0 TSI & 1.8 TSI / EA888 Gen 3 engines 2.0 TSI  / EA888 Gen 3B engines > VW Golf 7 & 7.5 GTI & Clubsport 2013-2020 > VW Golf 7 & 7.5 R 2013-2020 > VW Golf 7 & 7.5 1.8 TSI 2013-2020 > VW Passat 2.0 TSI B8 2015+ > VW Passat 2.0 TSI 190hp B8 2018+ > VW Arteon 2.0 TSI 2017+ > VW Arteon 2.0 TSI 190hp 2017+ > VW Arteon R 2.0 TSI 320ps 2020+ > VW T-Roc R 2.0 TSI 2019+ > VW T-Roc 2.0 TSI 190hp 2017+ > VW Tiguan II 2.0 TSI 2016+ > VW Jetta / GLI 7 2018+ > VW Polo 5 GTI 1.8 TSI 6C 2015-2018 > VW Polo 6 GTI 2.0 TSI AW 2017-2021 > Audi S1 2.0 TFSI 2015-2018 > Audi A1 2.0 40TFSI GB 2019-2021 > Audi S3 8V 2013-2020 > Audi A3 2.0 TSI / 1.8 TSI 8V 2013-2020 > Audi A3 40TFSI 2.0 TSI 190hp 2016-2020 > Audi TTS 2.0 TFSI 8S 2015-2021 > Audi SQ2 2018+ > Audi Q2 40 TFSI 2.0 TSI 190hp 2017+ > Audi Q3 45 TFSI 2.0 TSI 2018+ > Audi Q3 40 TFSI 2.0 TSI 190hp 2018+ > SEAT Leon III Cupra 5F 2014-2020 > SEAT Leon III 2.0 TSI 190hp 5F 2018+ > SEAT Leon III 1.8 TSI 5F 2014-2020 > Cupra Formentor 2020+ > Cupra Ateca 2018+ > SEAT Ateca 2.0 TSI 190hp 2017+ > SEAT Tarraco 2.0 TSI 2018+ > SEAT Tarraco 2.0 TSI 190ps 2018+ > SEAT Tarraco 2.0 TSI 245ps 2021+ > Skoda Octavia III vRS 2.0 TSI 5E 2014-2020 > Skoda Octavia III 2.0 TSI 190hp 5E 2017-2020 > Skoda Superb III 1.8 / 2.0 TSI 3V 2015+ > Skoda Superb III 2.0 TSI 190hp 3V 2019+ > Skoda Kodiaq 2018+ > Skoda Kodiaq 2.0 TSI 190hp 2018+

Read more less